User Manual
Table Of Contents
- Table of Contents
- System Description
- Microwave Path Engineering Basics
- Engineering Guidelines
- Network Turnup Procedure
- User Interface Guide
- 1. Navigating the Terminal Menu
- 2. Menu and System Control
- 3. Menu Descriptions
- > System Status
- > Main Menu
- > System Configuration
- > RF Link Configuration
- > RF Link Performance History (Main Screen)
- > RF Link Error History
- > RF Link Max/Min Received Power History
- > RF Link Min/Max Received Signal Quality History
- > Datapath Provisioning
- > 4xE1 Module Configuration/Status/History (Main Screen)
- > E1x Status/Configuration/Loopback
- > E1x Performance History
- > T1 Module Configuration/Status/History (Main Screen)
- > T1x Status/Configuration/Loopback
- > Ethernet Switch Module Configuration/Status/History (Main Screen)
- > Ethernet Switch Configuration
- > Ethernet Switch Status
- > Management/Utilities (Main Screen)
- > Ping Utility
- > Firmware Upgrade Utility
- > RF Link Management Bridge Configuration
- > System Alarms
- Detail Level Procedures
- MIBs
- Troubleshooting Guide
- 1. Overview
- 2. LED Indicators
- PWR LED
- TST LED
- RF DWN LED
- RF LOW LED
- T1 Interface Alarms
- E1 Interface Alarms
- 1. Display the E1(x) Status screen and check the E1(x) Interface Alarm field to identify the active alarm.
- 1. Verify that the E1 cable is connected to the E1 interface on the TRACER 64x0.
- 2. Verify the connections at the opposite end of the E1 cable.
- 3. Verify that the framing mode (framed, multiframed, or unframed) is the same for both the TRACER 64x0 and the E1 equipment.
- 2. Verify the cable connections for the E1 interface are solid.
- 2. Verify the cable connections for the E1 interface are solid.
- System Alarms
- LAN LEDs
- 3. RF Errors
- 4. Step-by-Step Troubleshooting
- 5. Installing/Troubleshooting the TRACER Hardware
TRACER 6000 Series Integrated System Manual Section 7 MIBs
612806420L1-1E Copyright © 2005 ADTRAN, Inc. 119
adTRACERintervalRFCs* Integer RO
adTRACERintervalMaxRxLs Integer RO
adTRACERintervalMinRxLs Integer RO
adTRACERintervalMaxRxQs Integer RO
adTRACERintervalMinRxQs Integer RO
adTRACERintervalValidData TruthValue RO
adTRACERtotalTable
adTRACERtotalEntry
AdTRACERtotalEntry
adTRACERtotalNumber Integer RO
adTRACERtotalRFs Integer RO
adTRACERtotalRFCs* Integer RO
adTRACERtotalMaxRxLs Integer RO
adTRACERtotalMinRxLs Integer RO
adTRACERtotalMaxRxQs Integer RO
adTRACERtotalMinRxQs Integer RO
adTRACERtotalValidData TruthValue RO
adTRACER6000remoteStatus
adTRACERremoteRFlinkState DisplayString RO
adTRACERremoteRFClinkState* DisplayString RO
adTRACERremoteRFLow DisplayString RO
adTRACERremoteRXquality DisplayString RO
adTRACERremoteRXLevel DisplayString RO
adTRACERremoteFrequencyPlan DisplayString RO
adTRACERremoteLEDStatus DisplayString RO
adTRACERremoteSlot1 DisplayString RO
adTRACERremoteSlot2 DisplayString RO
adTRACER6000remoteCfg
adTRACERremoteBaudRate Integer RW
adTRACERremoteBandPlan Integer RW
adTRACERremoteActiveChannels Integer RW
adTRACERremoteChannelSelect
adTRACERremoteDSX1ChannelSelectTable
adTRACERremoteDSX1ChannelSelectEntry
AdTRACERremoteDSX1ChannelSelectEntry
adTRACERremoteDSX1ChannelSelectIdx Integer RO
adTRACERremoteDSX1ChannelSelection Integer RW
adTRACERremoteSwitchChannelSelectTable
Table 6. MIB Variables for TRACER6000.mib (Continued)
* Not supported in TRACER 64x0 models. Listed variable only applies to TRACER split systems.