User's Manual
Table Of Contents
- Table of Contents
- System Description
- Microwave Path Engineering Basics
- Engineering Guidelines
- Network Turnup Procedure
- User Interface Guide
- 1. Navigating the Terminal Menu
- 2. Menu and System Control
- 3. Menu Descriptions
- > System Status
- > Main Menu
- > System Configuration
- > RF Link Configuration
- > RF Link Performance History (Main Screen)
- > RF Link Error History
- > RF Link Max/Min Received Power History
- > RF Link Min/Max Received Signal Quality History
- > Datapath Provisioning
- > 4xE1 Module Configuration/Status/History (Main Screen)
- > E1x Status/Configuration/Loopback
- > E1x Performance History
- > T1 Module Configuration/Status/History (Main Screen)
- > T1x Status/Configuration/Loopback
- > Ethernet Switch Module Configuration/Status/History (Main Screen)
- > Ethernet Switch Configuration
- > Ethernet Switch Status
- > Management/Utilities (Main Screen)
- > Ping Utility
- > Firmware Upgrade Utility
- > RF Link Management Bridge Configuration
- > System Alarms
- Detail Level Procedures
- MIBs
- Troubleshooting Guide
- 1. Overview
- 2. LED Indicators
- PWR LED
- TST LED
- RF DWN LED
- RF LOW LED
- T1 Interface Alarms
- E1 Interface Alarms
- 1. Display the E1(x) Status screen and check the E1(x) Interface Alarm field to identify the active alarm.
- 1. Verify that the E1 cable is connected to the E1 interface on the TRACER 64x0.
- 2. Verify the connections at the opposite end of the E1 cable.
- 3. Verify that the framing mode (framed, multiframed, or unframed) is the same for both the TRACER 64x0 and the E1 equipment.
- 2. Verify the cable connections for the E1 interface are solid.
- 2. Verify the cable connections for the E1 interface are solid.
- LAN LEDs
- 3. RF Errors
- 4. Step-by-Step Troubleshooting
- 5. Installing/Troubleshooting the TRACER Hardware
TRACER 6000 Series Integrated System Manual Section 5 User Interface Guide
612806420L1-1D Copyright © 2005 ADTRAN, Inc. 81
>ETHERNET SWITCH CONFIGURATION > PORT X
The Quad Ethernet Switch module provides the capability to individually disable interfaces on the module.
Selecting
DISABLE from the PORT X menu disables the port, stopping all data passing through the interface.
>ETHERNET SWITCH CONFIGURATION > SPEED/DUPLEX
Defines the speed and duplex for the selected Ethernet interface. Available options are: 100/FDX (100
Mbps with full-duplex operation),
100/HDX (100 Mbps with half-duplex operation), 10/FDX (10 Mbps
with full-duplex operation), and
10/HDX (10 Mbps with half-duplex operation), and AUTO (automatically
detects speed and duplex of the connection). The speed and duplex settings of the TRACER Ethernet port
and the attached Ethernet equipment should be identical; if the TRACER is set to auto-negotiation, the
attached equipment should also be set for auto-negotiation.When the
SPEED/DUPLEX is manually set,
802.3u auto-negotiation is disabled; the Ethernet equipment connected to the manual port must be
manually set to the same speed/duplex settings. When set to
AUTO, the actual negotiated speed and duplex
of the system can be displayed on the Ethernet Switch Status page.
> ETHERNET SWITCH STATUS
Figure 29 shows the Ethernet Switch Status menu page, which displays the current speed and duplex
operation for each switch interface (on both the local and remote TRACER 64x0 systems) as well as
transmit and receive data statistics for the Ethernet interface (from both the local and remote TRACER
64x0 systems) and RF link.
Figure 29. Ethernet Switch Module Status
>ETHERNET SWITCH STATUS > TX PACKETS
Displays a counter of all data packets transmitted out the local and remote TRACER 64x0 Ethernet
interfaces. Use this data as an indicator for how many packets are being transmitted between the four
Ethernet interfaces versus over the wireless link (WAN stats). The WAN statistics (Ethernet packets
transmitted over the RF link) provide a quick way to determine Ethernet packet loss over the wireless link;
the
RX PACKETS on the local system should match the TX PACKETS on the remote side (and vice versa).
>ETHERNET SWITCH STATUS > TX PACKETS DROPPED
Displays a counter of all transmit data packets that were unable to be transmitted out the individual
Ethernet interfaces (for both the local and remote TRACER 64x0 units). Use this data as an indicator of
congestion on the Ethernet network segments. Dropped packets on the WAN interface can indicate that the
provisioned bandwidth for the switch module is insufficient.