User's Manual
Table Of Contents
- Table of Contents
- System Description
- Microwave Path Engineering Basics
- Engineering Guidelines
- Network Turnup Procedure
- User Interface Guide
- 1. Navigating the Terminal Menu
- 2. Menu and System Control
- 3. Menu Descriptions
- > System Status
- > Main Menu
- > System Configuration
- > RF Link Configuration
- > RF Link Performance History (Main Screen)
- > RF Link Error History
- > RF Link Max/Min Received Power History
- > RF Link Min/Max Received Signal Quality History
- > Datapath Provisioning
- > 4xE1 Module Configuration/Status/History (Main Screen)
- > E1x Status/Configuration/Loopback
- > E1x Performance History
- > T1 Module Configuration/Status/History (Main Screen)
- > T1x Status/Configuration/Loopback
- > Ethernet Switch Module Configuration/Status/History (Main Screen)
- > Ethernet Switch Configuration
- > Ethernet Switch Status
- > Management/Utilities (Main Screen)
- > Ping Utility
- > Firmware Upgrade Utility
- > RF Link Management Bridge Configuration
- > System Alarms
- Detail Level Procedures
- MIBs
- Troubleshooting Guide
- 1. Overview
- 2. LED Indicators
- PWR LED
- TST LED
- RF DWN LED
- RF LOW LED
- T1 Interface Alarms
- E1 Interface Alarms
- 1. Display the E1(x) Status screen and check the E1(x) Interface Alarm field to identify the active alarm.
- 1. Verify that the E1 cable is connected to the E1 interface on the TRACER 64x0.
- 2. Verify the connections at the opposite end of the E1 cable.
- 3. Verify that the framing mode (framed, multiframed, or unframed) is the same for both the TRACER 64x0 and the E1 equipment.
- 2. Verify the cable connections for the E1 interface are solid.
- 2. Verify the cable connections for the E1 interface are solid.
- LAN LEDs
- 3. RF Errors
- 4. Step-by-Step Troubleshooting
- 5. Installing/Troubleshooting the TRACER Hardware
Section 7 MIBs TRACER 6000 Series Integrated System Manual
120 Copyright © 2005 ADTRAN, Inc. 612806420L1-1D
adTRACERintervalCSU1Des Integer RO
adTRACERintervalCSU1Dses Integer RO
adTRACERIntervalValidData TruthValue RO
adTRACERcsu2IntervalTable
adTRACERcsu2IntervalEntry
AdTRACERcsu2IntervalEntry
adTRACERcsu2IntervalIndex Integer RO
adTRACERcsu2IntervalNumber Integer RO
adTRACERintervalCSU2Aes Integer RO
adTRACERintervalCSU2Ases Integer RO
adTRACERintervalCSU2Bes Integer RO
adTRACERintervalCSU2Bses Integer RO
adTRACERintervalCSU2Ces Integer RO
adTRACERintervalCSU2Cses Integer RO
adTRACERintervalCSU2Des Integer RO
adTRACERintervalCSU2Dses Integer RO
adTRACERIntervalValidData TruthValue RO
adTRACER6000current
adTRACERcurrentRFs Integer RO
adTRACERcurrent24hRFs Integer RO
adTRACERcurrentRFCs* Integer RO
adTRACERcurrent24hRFCs* Integer RO
adTRACERcurrentRxLs Integer RO
adTRACERcurrentMaxRxLs Integer RO
adTRACERcurrent24hMaxRxLs Integer RO
adTRACERcurrentMinRxLs Integer RO
adTRACERcurrent24hMinRxLs Integer RO
adTRACERcurrentRxQs Integer RO
adTRACERcurrentMaxRxQs Integer RO
adTRACERcurrent24hMaxRxQs Integer RO
adTRACERcurrentMinRxQs Integer RO
adTRACERcurrent24hMinRxQs Integer RO
adTRACERintervalTable
adTRACERintervalEntry
AdTRACERintervalEntry
adTRACERintervalIndex Integer RO
adTRACERintervalNumber Integer RO
adTRACERintevalRFs Integer RO
Table 6. MIB Variables for TRACER6000.mib (Continued)
* Listed variable only applies to TRACER split systems.