User's Manual
Table Of Contents
- Table of Contents
- System Description
- Microwave Path Engineering Basics
- Engineering Guidelines
- Network Turnup Procedure
- User Interface Guide
- 1. Navigating the Terminal Menu
- 2. Menu and System Control
- 3. Menu Descriptions
- > System Status
- > Main Menu
- > System Configuration
- > RF Link Configuration
- > RF Link Performance History (Main Screen)
- > RF Link Error History
- > RF Link Max/Min Received Power History
- > RF Link Min/Max Received Signal Quality History
- > Datapath Provisioning
- > 4xE1 Module Configuration/Status/History (Main Screen)
- > E1x Status/Configuration/Loopback
- > E1x Performance History
- > T1 Module Configuration/Status/History (Main Screen)
- > T1x Status/Configuration/Loopback
- > Ethernet Switch Module Configuration/Status/History (Main Screen)
- > Ethernet Switch Configuration
- > Ethernet Switch Status
- > Management/Utilities (Main Screen)
- > Ping Utility
- > Firmware Upgrade Utility
- > RF Link Management Bridge Configuration
- > System Alarms
- Detail Level Procedures
- MIBs
- Troubleshooting Guide
- 1. Overview
- 2. LED Indicators
- PWR LED
- TST LED
- RF DWN LED
- RF LOW LED
- T1 Interface Alarms
- E1 Interface Alarms
- 1. Display the E1(x) Status screen and check the E1(x) Interface Alarm field to identify the active alarm.
- 1. Verify that the E1 cable is connected to the E1 interface on the TRACER 64x0.
- 2. Verify the connections at the opposite end of the E1 cable.
- 3. Verify that the framing mode (framed, multiframed, or unframed) is the same for both the TRACER 64x0 and the E1 equipment.
- 2. Verify the cable connections for the E1 interface are solid.
- 2. Verify the cable connections for the E1 interface are solid.
- LAN LEDs
- 3. RF Errors
- 4. Step-by-Step Troubleshooting
- 5. Installing/Troubleshooting the TRACER Hardware
Section 7 MIBs TRACER 6000 Series Integrated System Manual
114 Copyright © 2005 ADTRAN, Inc. 612806420L1-1D
TRACER6000.mib adTRACERBPVoff a change in the BiPolar Violation (BPV) state has
occurred and the BPV alarm is inactive.
adTRACERRAoff a change in the Frame RA (Remote Alarm) state has
occurred and the RA alarm is inactive.
adTRACEROOFoff a change in the Out Of Frame (OOF) state has
occurred and the OOF alarm is inactive.
adTRACERCVoff a change in the Code Violation (CV) state has
occurred and the CV alarm is inactive.
adTRACERCRCoff a change in the Cyclic Redundancy Check (CRC)
state has occurred and the CRC alarm is inactive.
adTRACERmfLOFoff a change in the Loss of Multiframe (LOMF) state has
occurred and the LOMF alarm is inactive.
adTRACERmfLOSoff a change in the Multiframe Loss of Signal (LOS)
state has occurred and the Multiframe LOS alarm is
inactive.
adTRACERmfAISoff a change in the Multiframe Alarm Indication Signal
(AIS) state has occurred and the Multiframe AIS
alarm is inactive.
adTRACERmfRAoff a change in the Multiframe Remote Alarm (RA) has
occurred and the Multiframe RA alarm is inactive.
adTRACERlineLoopbackOff a change in the line loopback state has occurred and
the line loopback is inactive.
adTRACERlinkLoopbackOff a change in the link loopback state has occurred and
the link loopback is inactive.
adTRACERLinkDown the RF link is down.
adTRACERLinkUp the RF link is up.
adTRACERRFCLinkDown the RFC link is down between the Indoor Unit (IDU)
and Outdoor Unit (ODU). This trap only applies to
TRACER split systems.
adTRACERRFCLinkUp the RFC link is up between the IDU and ODU. This
trap only applies to TRACER split systems.
adTRACERRxLow the receive level is within 10 dB of sensitivity and the
RF Low alarm is active.
adTRACERRxLevel a change in receive level has occurred and the
receive level is within normal range.
adTRACERcurrThrsESon the threshold for current Errored Seconds (ES) has
been exceeded.
adTRACERcurrThrsESoff the threshold for current ES has not been exceeded.
adTRACERcurrThrsSESon the threshold for current Severely Errored Seconds
(SES) has been exceeded.
adTRACERcurrThrsSESoff the threshold for current SES has not been
exceeded.
Table 3. Traps Supported by the TRACER 64x0 (Continued)
MIB Trap This trap indicates that....