User manual

ManualsBrandsADTRAN ManualsNetworkingNetwork Router 1700600L2

NetVanta 3100 Series

Fixed Port Routers

Hardware Installation Guide

1700600L2 NetVanta 3120 (with DBU)

1700601G2 NetVanta 3120 (without DBU)

1700610L2 NetVanta 3130 Annex A (with DBU)

1700611G2 NetVanta 3130 Annex A (with DBU)

1700612G2 NetVanta 3130 Annex B (without DBU)

61700600L2-34A

December 2012

Summary of content (26 pages)

PAGE 1
NetVanta 3100 Series Fixed Port Routers Hardware Installation Guide 61700600L2-34A December 2012 1700600L2 NetVanta 3120 (with DBU) 1700601G2 NetVanta 3120 (without DBU) 1700610L2 NetVanta 3130 Annex A (with DBU) 1700611G2 NetVanta 3130 Annex A (with DBU) 1700612G2 NetVanta 3130 Annex B (without DBU)
PAGE 2
Trademarks NetVanta 3100 Series Hardware Installation Guide Trademarks Any brand names and product names included in this manual are trademarks, registered trademarks, or trade names of their respective holders. To the Holder of the Manual The contents of this manual are current as of the date of publication. ADTRAN reserves the right to change the contents without prior notice.
PAGE 3
NetVanta 3100 Series Hardware Installation Guide Conventions Conventions Notes provide additional useful information. Cautions signify information that could prevent service interruption or damage to the equipment. Warnings provide information that could prevent injury or endangerment to human life. 61700600L2-34A Copyright © 2012 ADTRAN, Inc.
PAGE 4
Safety Instructions NetVanta 3100 Series Hardware Installation Guide Safety Instructions When using your telephone equipment, please follow these basic safety precautions to reduce the risk of fire, electrical shock, or personal injury: 1. Do not use this product near water, such as a bathtub, wash bowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool. 2. Avoid using a telephone (other than a cordless type) during an electrical storm. There is a remote risk of shock from lightning.
PAGE 5
NetVanta 3100 Series Hardware Installation Guide FCC-Required Information FCC-Required Information FCC regulations require that the following information be provided in this manual: 1. This equipment complies with Part 68 of Federal Communications Commission (FCC) rules and requirements adopted by America’s Carriers Telecommunications Association (ACTA). Each registered interface has a label that contains, among other information, a product identifier in the format US:AAAEQ##TXXXX.
PAGE 6
FCC Radio Frequency Interference Statement NetVanta 3100 Series Hardware Installation Guide FCC Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
PAGE 7
Table of Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Physical Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . NetVanta 3120 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 9
List of Figures Figure 1. Figure 2. Figure 3. Figure 4. Figure 5. Figure 6. Figure 7. Figure 8. Figure 9. Figure 10. NetVanta 3120 (with DBU) Front Panel Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . NetVanta 3120 (without DBU) Front Panel Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . NetVanta 3120 (with DBU) Rear Panel Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . NetVanta 3120 (without DBU) Rear Panel Layout . . . . .
PAGE 11
List of Tables Table 1. Table A-1. Table A-2. Table A-3. 61700600L2-34A NetVanta 3100 Series Front Panel LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10/100Base-T Ethernet Port Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DBU Connector Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ADSL Connector Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 13
1. INTRODUCTION The NetVanta 3100 Series Fixed Port Routers includes the NetVanta 3120 (with dial backup (DBU)), NetVanta 3120 (without DBU), NetVanta 3130 (with DBU) and NetVanta 3130 (without DBU). In this document, the term NetVanta 3100 means all of the units collectively. If a statement only applies to one particular router, the text refers to the router individually.
PAGE 14
Physical Descriptions 2. NetVanta 3100 Series Hardware Installation Guide PHYSICAL DESCRIPTIONS NetVanta 3120 The NetVanta 3120 is a fixed-port Ethernet router with an integral four-port Ethernet switch. It provides a single auto-sensing 10/100Base-T Ethernet network interface and four auto-sensing 10/100Base-T Ethernet LAN interfaces. This product is ideal for enterprise-level Internet access for secure, high-speed corporate connectivity using broadband access such as DSL or cable.
PAGE 15
NetVanta 3100 Series Hardware Installation Guide Physical Descriptions NetVanta 3120 Shipping Contents Each NetVanta 3120 unit is shipped in its own cardboard shipping carton. Open each carton carefully, and avoid deep penetration into the carton with sharp objects. After unpacking the unit, inspect it for possible shipping damage.
PAGE 16
Physical Descriptions NetVanta 3100 Series Hardware Installation Guide NetVanta 3120 Rear Panel Design The NetVanta 3120 rear panel is shown below. Appendix A on page 25 provides pinouts. ETH 0/1 1 DBU 2 3 4 1 0 Default Switch Figure 3. NetVanta 3120 (with DBU) Rear Panel Layout ETH 0/1 1 2 3 4 1 0 Default Switch Figure 4. NetVanta 3120 (without DBU) Rear Panel Layout NetVanta 3120 Rear Panel Interfaces 10/100Base-T Ethernet Interface The Ethernet port (ETH 0/1) is an RJ-45 connector.
PAGE 17
NetVanta 3100 Series Hardware Installation Guide Physical Descriptions The default switch must be pressed WHILE the STAT light is flashing green. Do not press the default switch BEFORE the STAT light is flashing green, as this will cause boot to be missed. If the factory default switch is pressed and held for 5 seconds after boot, the switch ports on the NetVanta 3120 will default to 10.10.10.1 and all access policies will be removed from those interfaces.
PAGE 18
Physical Descriptions • • • • • • • • NetVanta 3100 Series Hardware Installation Guide AAA support using local user database, RADIUS, and TACACS+ Flash memory supports multiple images of AOS Remotely configurable and field upgradeable using TFTP or FTP (1700611G2 only) Telnet, HTTP, SSH, or SNMP management options 1.63-inch H x 9.00-inch W x 6.38-inch D DC power (12 VDC, 800 mA, 7.
PAGE 19
NetVanta 3100 Series Hardware Installation Guide Physical Descriptions NetVanta 3130 STAT SWITCH WAN VPN INET 1 4 3 2 Figure 6. NetVanta 3130 (without DBU) Front Panel Layout NetVanta 3130 Rear Panel Design The NetVanta 3130 rear panel is shown below. Appendix A on page 25 provides pinouts. ADSL 1 DBU 2 3 4 1 0 Default Switch Figure 7. NetVanta 3130 (with DBU) Rear Panel Layout 1 ADSL 2 3 4 1 0 Default Switch Figure 8.
PAGE 20
Physical Descriptions NetVanta 3100 Series Hardware Installation Guide DBU Interface (1700610L2 only) The NetVanta 3130 has a DBU port on the rear panel to provide analog, V.90 dial backup. See Table A-2 on page 25 for the DBU connector pinouts. Factory Default Switch The NetVanta 3130 has a factory default switch (labeled in Figure 7) on the rear of the unit. If the factory default switch is pressed during bootup, the unit will stay in bootstrap mode.
PAGE 21
NetVanta 3100 Series Hardware Installation Guide Physical Descriptions NetVanta 3100 Series Front Panel LEDs Table 1 describes the front panel LEDs. Table 1.
PAGE 22
Unit Installation 3. NetVanta 3100 Series Hardware Installation Guide UNIT INSTALLATION The instructions and guidelines provided in this section cover hardware installation topics, such as wall mounting/rack mounting the unit and installing option cards.
PAGE 23
NetVanta 3100 Series Hardware Installation Guide • • • Unit Installation To avoid damaging the unit, use only the screws included in the shipment when attaching mounting ears to the chassis. When wall mounting the NetVanta, care must be taken not to damage the power cord. Do not attach the power cord to the building surface or run it through walls, ceilings, floors, or openings in the building structure. The socket-outlet must be installed near the equipment and must be easily accessible.
PAGE 24
Unit Installation NetVanta 3100 Series Hardware Installation Guide Supplying Power to the Unit The NetVanta 3100 Series comes equipped with a 12 VDC power supply for connecting to the proper power receptacles. Instructions for Powering the NetVanta 3100 Series Step Action 1 To insert the 12 VDC power connector, pull the outer sheath back from the metal connector, as shown in Figure 10.
PAGE 25
APPENDIX A. CONNECTOR PIN DEFINITIONS The following tables provide the pin assignments for the NetVanta 3100 Series base units. Base Unit Pinouts Table A-1.