Router System Manual

ManualsBrandsADTRAN ManualsNetwork RouterMX412

MX410/MX412 System Manual

Document Number: 61189500L1-1B

August 2005

PRELIMINARY

Summary of content (108 pages)

PAGE 1
® MX410/MX412 System Manual Document Number: 61189500L1-1B August 2005 PRELIMINARY
PAGE 2
MX410/MX412 System Manual Trademarks Front Matter Any brand names and product names included in this manual are trademarks, registered trademarks, or trade names of their respective holders. To the Holder of the Manual The contents of this publication are current as of the date of publication. ADTRAN® reserves the right to change the contents without prior notice.
PAGE 3
MX410/MX412 System Manual Revision History Revision Date A June 2005 B August 2005 Description of Changes Initial release PPP and MX412 information added Conventions The following typographical conventions are used in this document: This font indicates a cross-reference link. First-time references to tables and figures are shown in this font. This font indicates screen menus, fields, and parameters. THIS FONT indicates keyboard keys (ENTER, ESC, ALT).
PAGE 4
MX410/MX412 System Manual Compliance The MX410 (P/N 1189500L1) and MX412 (P/N 1189512L1) comply with the requirements covered under UL 60950 and NEBS Level 3. The MX410 and MX412 are intended to be installed in a restricted access area only. The MX410 and MX412 devices comply with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. The device may not cause harmful interference. 2.
PAGE 5
MX410/MX412 System Manual Training ADTRAN offers training courses on our products. These courses include overviews on product features and functions while covering applications of ADTRAN’s product lines. ADTRAN provides a variety of training options, including customized training and courses taught at our facilities or at customer sites. For inquiries concerning training, contact ADTRAN: Training Phone: 800-615-1176, ext. 7500 Training Fax: 256-963-6700 Training Email: training@adtran.
PAGE 6
MX410/MX412 System Manual This page is intentionally blank.
PAGE 7
MX410/MX412 System Manual Contents Section 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Section 2 Engineering Guidelines. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 8
MX410/MX412 System Manual Front Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5 MX410 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5 MX412 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5 V.
PAGE 9
Contents DS1 Test Pattern Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Performance Monitoring Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Daily Performance Monitoring Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Quarter Hour Performance Monitoring Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 10
MX410/MX412 System Manual Figures Figure 1-1. Figure 1-2. Figure 3-1. Figure 3-2. Figure 3-3. Figure 3-4. Figure 3-5. Figure 3-6. Figure 3-7. Figure 3-8. Figure 3-9. Figure 3-10. Figure 3-11. Figure 3-12. Figure 3-13. Figure 3-14. Figure 3-15. Figure 3-16. Figure 3-17. Figure 3-18. Figure 3-19. Figure 3-20. Figure 3-21. Figure 3-22. Figure 3-23. Figure 4-1. Figure 4-2. Figure 4-3. Figure 4-4. Figure 4-5. Figure 4-6. Figure 5-1. Figure 5-2. Figure 5-3. Figure 5-4. Figure 5-5. Figure 5-6. Figure 5-7.
PAGE 11
Contents Figure 5-18. Figure 5-19. Figure 5-20. Figure 5-21. Figure 5-22. Figure 5-23. Figure 5-24. Figure 5-25. Figure 5-26. Figure 5-27. Figure 5-28. Figure 5-29. Figure 5-30. Figure 5-31. Figure 5-32. Figure 5-33. Figure 5-34. Figure 5-35. Figure 5-36. Figure 5-37. Network Management Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-31 Ethernet Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 12
MX410/MX412 System Manual Table 5-10. Cross-Connect Mapping Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-25 Table 5-11. Performance Monitoring Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 13
Section 1 Introduction PRODUCT OVERVIEW The MX410/MX412 delivers full DS0 control to service locations, allowing carriers full utilization of DS1 bandwidth. The MX410 interfaces to four long-haul outside plant protected DS1s via RJ-48 connectors, while the MX412 interfaces to 12 DS1s. Data and management on the DS1s can be cross connected on a non-blocking per-DS0 basis to any DS1, V.35 port, and four PPP ports.
PAGE 14
Product Overview MX410/MX412 System Manual The major features of the MX410/MX412 are as follows: • 19-inch wall mounting or rack mounting, one rack unit high • Front panel data connections • One V.35 port • Four RJ-45 long-haul DS1 connections (12 on the MX412) with outside plant protection • A four-port Ethernet switch • Non-Blocking DS0 cross connect between all DS1 interfaces and the V.
PAGE 15
MX410/MX412 System Manual Product Overview Digital Radios Data Analog Radios Data Grooming of DS0S LAN Extension over PPP for Remote Management Star Configuration of Backhaul Backhaul 12 x T1 (I/O) Battery Backup HVAC Backhaul Radio Management 4 x RS-232 V.35 DB-9 Craft Interface FXS E911, etc. 4 x 10/100 Ethernet Figure 1-2.
PAGE 16
Product Overview MX410/MX412 System Manual This page is intentionally blank.
PAGE 17
Section 2 Engineering Guidelines GENERAL This section provides engineering guidelines for network designers who are incorporating an MX410 or MX412 system into their network. POWER REQUIREMENTS Table 2-1 provides the current draw at –48 VDC (operating range of –42 VDC to –60 VDC) and ±24 VDC (operating range of ±22 VDC to ±27 VDC) with redundant PSUs installed. Table 2-1.
PAGE 18
Power Dissipation MX410/MX412 System Manual POWER DISSIPATION Table 2-3 provides the heat dissipation data at –48 VDC (operating range of –42 VDC to –60 VDC) and ±24 VDC (operating range of ±22 VDC to ±27 VDC) with redundant PSUs installed (MX410 only). Table 2-3. Heat Dissipation at –48 VDC and ±24 VDC Part Number Equipment Heat Dissipation at –48 VDC Heat Dissipation at ±24 VDC 1189500L1 MX410 11.8 watts 10.5 watts 1189512L1 MX412 17.3 watts 18.
PAGE 19
Section 3 Application Guidelines INTRODUCTION This section describes several applications for the MX410/MX412 system. For each application there is a figure illustrating the application, a list of the equipment needed, and an explanation of the basic setup.
PAGE 20
MX410/MX412 System Manual MX410 DATA PATH BLOCK DIAGRAM As shown in Figure 3-1, the MX410/MX412 contains a 1/0 cross connect that allows DS0s to be mapped between four DS1s (12 DS1s on the MX412), four PPP ports, and a V.35 port. Refer to “PPP BCP/IPCP Menu” on page 5-32 for more information about using PPP. Any DS0 in DS1 1 can be mapped to any DS0 in DS1 1-4, or any PPP port, or the V.35 port. Any unmapped DS0 in a DS1 is filled with all ones.
PAGE 21
MX410/MX412 System Manual Drop and Continue Application Drop and Continue Application The following applies to Remote Site #1 shown in Figure 3-2. In the Drop and Continue Application, any combination of DS0s from one DS1 can be dropped out the other DS1 ports with the remaining DS0s continuing through to the other DS1 interface. This enables the bandwidth of one DS1 to deliver DS0s to several sites using one MX410 at each site.
PAGE 22
Drop and Continue Application MX410/MX412 System Manual Setup Connect the incoming DS1 (the DS1 from which the DS0s are dropped) to the DS1 1 RJ. Connect the outgoing DS1 to the DS1 2 RJ. Connect the other DS1s using the RJ connector on the front panel. For more information, refer to “DS1 Ports” on page 4-6. Starting from the default blank mapping, the DS0s can be dropped using the Quick Setup menu to the PPP and V.35 ports (see Figure 3-3). Select each port (PPP1-4, V.
PAGE 23
MX410/MX412 System Manual Drop and Continue Application Figure 3-4 shows the Quick Setup menu after DS0s 21-22 have been dropped from DS1 1 to PPP1, DS0s 23-24 have been dropped from DS1 1 to the V.35 port. Active Alarms: CRITICAL MX410 MINOR ID: MM/DD/YY HH:MM MX410 Quick Setup Ports 1 - PPPs PPP 1 = DS1 4 DS0 #1 2 - V.35 = System 3 - System ID 4 - IP Address Subnet Mask 5 - Default Gateway 6 - Date 7 - Time : 192.168.100.1 : 255.255.0.0 : 192.168.1.
PAGE 24
Drop and Continue Application MX410/MX412 System Manual Figure 3-6 shows the Cross-Connect Mapping menu after the remaining DS0s have been continued to DS1 2 as well as 4 DS0s (13-16) dropped to DS1 3 (1-4) and four other DS0s (17-20) dropped to DS1 4 (1-4).
PAGE 25
MX410/MX412 System Manual Drop and Insert Application Drop and Insert Application The following applies to Remote Site #1 shown in Figure 3-7. In the Drop and Insert Application DS0s from one DS1 can be dropped out to the other DS1 ports. Then, DS0s from the other DS1 ports can be inserted into the corresponding DS0s in the other DS1. In the example shown, any DS0 not dropped will be mapped to continue on from one DS1 to another. This allows a DS1 to be used to transport DS0s between several sites.
PAGE 26
Drop and Insert Application MX410/MX412 System Manual Setup Connect the DS1 from which the DS0s will be dropped to the DS1 1 RJ. Connect the other DS1 to which the DS0s will be inserted to the DS1 2 RJ. Connect the other DS1s using the other RJ connectors on the front panel. For more information, refer to “DS1 Ports” on page 4-6 Starting from the default mapping the DS0s can be dropped and inserted using the Quick Setup menu (see Figure 5-24 on page 5-38).
PAGE 27
MX410/MX412 System Manual Drop and Insert Application Figure 3-9 shows the Quick Setup menu after DS0s 23-24 have been dropped from DS1 1 to PPP1 and PPP 2 has been inserted into DS0s 23-24 in DS1 2. MX410 MINOR Active Alarms: CRITICAL ID: MM/DD/YY HH:MM MX410 Quick Setup Ports 1 - PPPs PPP 1 PPP 2 2 - V.35 = DS1 1 DS0 #23-24 = DS1 2 DS0 #23-24 = DS1 1 DS0 #23-24 System 3 - System ID 4 - IP Address Subnet Mask 5 - Default Gateway 6 - Date 7 - Time : 192.168.100.1 : 255.255.0.0 : 192.168.1.
PAGE 28
Drop and Insert Application MX410/MX412 System Manual Figure 3-11 shows the Cross-Connect Mapping menu after DS0s 1-12 are continued through from DS1 1 to DS1 2 and DS0s 13-23 are dropped from DS1 1 to DS1 3.
PAGE 29
MX410/MX412 System Manual Drop and Insert Application Figure 3-13 the Cross-Connect Mapping menu after DS0s 13-23 are inserted in DS1 2 from DS1 4. Any unmapped DS0s will be filled with all ones.
PAGE 30
Integrated Wireless Access Device or DS0 Grooming MX410/MX412 System Manual Integrated Wireless Access Device or DS0 Grooming The following applies to Remote Site #1 shown in Figure 3-14 and Figure 3-15. In the Integrated Wireless Access Device Application, bandwidth is conserved by using the MX410 to groom multiple fractional T1s into a single T1. This allows the MX410 to be used as an integrated wireless access device (see Figure 3-14) or to transport DS0s between several sites (see Figure 3-15).
PAGE 31
MX410/MX412 System Manual Integrated Wireless Access Device or DS0 Grooming DS1 Central Site 24 DS0s from Central Site DS1 DS1 µ Wave/ Leased DS1 Drop DS0s to/from Local Equipment Drop DS0s to PPP to Control Local Equipment via Ethernet.
PAGE 32
Integrated Wireless Access Device or DS0 Grooming MX410/MX412 System Manual Setup Connect the DS1 from which the DS0s will be dropped to the DS1 1 RJ. Connect the other DS1s to DS1 2, 3 and 4 RJ. For more information, refer to “DS1 Ports” on page 4-6. Starting from the default mapping the DS0s can be mapped using the Quick Setup menu shown in Figure 3-16. Select each port to which a DS0 needs to be dropped from the incoming DS1. For each port select the DS0(s) in DS1 1 to be dropped to that port.
PAGE 33
MX410/MX412 System Manual Integrated Wireless Access Device or DS0 Grooming Figure 3-17 shows the Quick Setup menu after DS0s 23-24 have been dropped from DS1 1 to PPP1, and PPP 2, 3, and 4 have been inserted into DS0s 23-24 in DS1 2, 3 and 4 respectively. PPP 2, 3, and 4 are typically not used in this fashion for the integrated wireless access device application. MX410 MINOR Active Alarms: CRITICAL ID: MM/DD/YY HH:MM MX410 Quick Setup Ports 1 - PPPs PPP 1 PPP 2 PPP 3 PPP 4 2 - V.
PAGE 34
Integrated Wireless Access Device or DS0 Grooming MX410/MX412 System Manual Figure 3-19 shows the Cross-Connect Mapping menu after DS0s 1-7 are mapped from DS1 1 to DS1 2, DS0s 8-15 are mapped from DS1 1 to DS1 3, and DS0s 15-22 are mapped from DS1 1 to DS1 4.
PAGE 35
MX410/MX412 System Manual Integrated Wireless Access Device or DS0 Grooming Figure 3-21 shows the Cross-Connect Mapping menu for DS1 3.
PAGE 36
Remote Management of Other Systems using Terminal Server Ports and Ethernet Connectivity MX410/MX412 System Manual Remote Management of Other Systems using Terminal Server Ports and Ethernet Connectivity In this application the Terminal Server ports on the MX410 are used to provide remote management of other non-Ethernet based equipment at the same site. This requires connecting the RS-232 craft ports of the other equipment to the Terminal Server ports of the MX410.
PAGE 37
MX410/MX412 System Manual Remote Management of Other Systems using Terminal Server Ports and Ethernet Connectivity Setup First, connect the RS-232 craft port on the other equipment to the MX410 terminal server port. The pin assignments for each of the RS-232 interfaces are listed in the PORT 1-4 Terminal Server port pin list in Table 4-5 on page 4-8. The default settings for the terminal server ports are 9600 bps 8 data bits with no parity.
PAGE 38
Remote Management of Other Systems using Terminal Server Ports and Ethernet Connectivity MX410/MX412 System Manual This page is intentionally blank.
PAGE 39
Section 4 Installation GENERAL The first three tasks for installing and operating the MX410/MX412 are to unpack, inspect, and install. Those tasks are detailed in this section of the manual, as well as information for mounting the MX410/MX412 into an equipment rack or to a wall, making the proper connections to the front and back panels, identifying the front panel indicators, and adding or removing a Power Supply Unit (PSU) (MX410 only).
PAGE 40
Rackmount MX410/MX412 System Manual RACKMOUNT For a rackmount installation, perform the following steps: 1. Ensure the mounting brackets to the MX410/MX412 are attached using the two screws provided for each bracket. • For 19-inch rack applications, attach the brackets with the short flange parallel with the front of the chassis (see Figure 4-1). • For 23-inch rack applications, attach the brackets with the short flange parallel with the front of the chassis and obtain 23-inch adapter mounting hardware.
PAGE 41
MX410/MX412 System Manual Rear Panel REAR PANEL The MX410/MX412 rear panel is equipped with wire-wrap pins for external auxiliary inputs, wire-wrap pins for alarms (critical, major, and minor), a frame ground lug, and a single power connector for both DC power feeds (A and B). Figure 4-2 illustrates the rear panel. Figure 4-2. MX410/MX412 Rear View WARNING The Alarm interfaces and AUX inputs must not be metallically connected to interfaces which connect to the Outside Plant or its wiring.
PAGE 42
Rear Panel MX410/MX412 System Manual Alarm Contacts/AUX Inputs The alarm contacts and auxiliary (AUX) inputs are shown in Figure 4-4. Figure 4-4. Alarm Contacts and AUX Inputs The alarm interfaces connect to the nine Form C type relays on the MX410/MX412 labeled CRIT, MAJOR, and MINOR. Both NC (Normally Closed) and NO (Normally Open) contacts are provided.
PAGE 43
MX410/MX412 System Manual Front Panel FRONT PANEL The front panels for the MX410 and MX412 are described below. MX410 The MX410 front panel (see Figure 4-5) is equipped with the following: • One V.35 Port (refer to “V.
PAGE 44
Front Panel MX410/MX412 System Manual V.35 Port The V.35 port is a Nx64k serial interface (up to 1.536 Mbps) with a CCITT V.35, 34-pin connector. The V.35 connector pin list is shown in Table 4-2. Table 4-2. V.
PAGE 45
MX410/MX412 System Manual Front Panel Ethernet Ports The four Ethernet jacks labeled ETHERNET located on the MX410/MX412 front panel provide LAN access to the Network. From these ports, devices located on the local area network can be remotely managed. The Ethernet ports have automatic rate detection and perform MDI/MDI-X crossover detection eliminating the need for a crossover cable. The Ethernet ports can be accessed using standard CAT 5 cable with an RJ-45 connector.
PAGE 46
Front Panel MX410/MX412 System Manual Terminal Server Ports The four Terminal Server port RS-232 interfaces located on the front panel are used to remotely connect to RS-232 managed devices. CAUTION The 8-pin modular Terminal Server Port 1-4 jacks should never be connected to a telecommunications network and are intended for connection to RS-232 data interfaces only. The Terminal Server ports are accessed by establishing a Telnet session to the MX410/MX412 with the TCP Port Number of the particular port.
PAGE 47
MX410/MX412 System Manual Front Panel FXS Port The FXS port (MX412 only) provides a 2-wire analog interface between a Voice Frequency (VF) transmission and a signaling facility. The FXS interface provides for simultaneous signaling in each direction for use with 2-wire off-premises station lines, carrier extended PBX trunks, or subscriber line foreign exchanges using a loop start signaling system. FXS options are shown in Table 4-6. Table 4-6. FXS Options Mode Description Loop Start Selects ANSI T1.
PAGE 48
Front Panel MX410/MX412 System Manual LED Indicators The LEDs on the front panel of the MX410/MX412 indicate the status of the power, DS1, Ethernet, and alarm interfaces. See Table 4-7 for a listing of the LEDs and their indications. Table 4-7.
PAGE 49
MX410/MX412 System Manual Turn-up TURN-UP The following sections provide turn-up steps for applying power and logging in to the MX410/ MX412. Power Up To power up the MX410/MX412, perform the following steps: 1. Connect the MX410/MX412 to a reliably grounded –48 VDC or ±24 VDC source, which is electrically isolated from the AC source. NOTE A readily accessible disconnect device, such as a rackmount fuse and alarm panel that is suitably approved and rated should be incorporated into the fixed wiring.
PAGE 50
Turn-up MX410/MX412 System Manual 3. Install the power connector for DC power feeds A and B by connecting RET A, PWR A, RET B, and PWR B to the power connector. PWR refers to respective –48 VDC or ±24 VDC power sources, while RET refers to respective returns. a. Insert the power wires into the power connector and tighten the hold-down screws on the top of the power connector. b. Insert the power connector into the MX410/MX412 and tighten the two screws on the front of the power connector. 4.
PAGE 51
Section 5 User Interface INTRODUCTION This section provides detailed information on the following: • “System Management” on page 5-1 • “Logging in to the MX410/MX412” on page 5-2 • “Menu Structure” on page 5-3 • “Menu Layout and Navigation” on page 5-4 • “Menu Tree” on page 5-5 • “Menu Descriptions” on page 5-11 SYSTEM MANAGEMENT MX410/MX412 management and provisioning is facilitated by a series of intuitive menus that are accessible on a computer screen.
PAGE 52
Logging in to the MX410/MX412 MX410/MX412 System Manual – no parity (none) – one stop bit – no flow control 2. Set the PC for direct connect on the appropriate communications port (as opposed to dial up connection). 3. Plug the male end of the data cable into the MX410/MX412. Make connection to the PC or laptop as appropriate for the equipment. Telnet Session To access the MX410/MX412, use an appropriate Telnet client to access the management interface of the MX410/MX412 at the configured IP address.
PAGE 53
MX410/MX412 System Manual Menu Structure MENU STRUCTURE The menu structure for the MX410/MX412 is a layered menu tree. Each layer of the menu tree is displayed as a menu or a screen. This section defines the terminology used in conjunction with the MX410/MX412 menu system. NOTE To view the MX410/MX412 menu tree, refer to “Menu Tree” on page 5-5.
PAGE 54
Menu Layout and Navigation MX410/MX412 System Manual MENU LAYOUT AND NAVIGATION Figure 5-1 illustrates the basic menu layout used in the MX410/MX412 menu system. The MX410/MX412 Menu Layout figure is general in nature, and not all menus contain all of the elements shown in the figure.
PAGE 55
MX410/MX412 System Manual Menu Tree Table 5-1 shows the general keyboard commands for the MX410/MX412. Table 5-1. MX410/MX412 Keyboard Commands Keyboard Command Description BACKSPACE This keyboard command is used to delete the character to left of the cursor during keyboard input. ENTER (or Return) This keyboard command is used to terminate input. ESC This keyboard command is used to clear partial input data, or if none, return to previous menu.
PAGE 56
Menu Tree MX410/MX412 System Manual Unit Name CLEI Code Part Number Serial Number Product Revision MAC Address Code Version Code Checksum Boot Version Boot Checksum 1. Configuration Main Menu 1. Line Legnth 1. DS1 Provisioning - Port #1 2. DS1 Provisioning - Port #2 3. DS1 Provisioning - Port #3 4. DS1 Provisioning - Port #4 1. DS1 Ports 2. Line Coding 1. B8ZS 2. AMI 3. Loopback Detection 1. Enabled 2. Disabled 4. Framing 1. ESF 2. SF 5. SNMP Line Status Trap 1. Enabled 2. Disabled 6.
PAGE 57
MX410/MX412 System Manual Menu Tree B 1. Terminal State 1. Port 1 2. Port 2 3. Port 3 4. Port 4 4. Terminal Server 2. Baud Rate 3. Telnet Port Number 4. Security 5. Username 6. Password 1. Craft Port Baud Rate 5. General 2. Date 3. Time 4. System ID 5. Auto-Logoff Inactivity Time 1. Enabled 2. Disabled 1. 9600 2. 19200 3. 38400 4. 57600 5. 115200 New Port Number 1. Enabled 2. Disabled New Username New Password 1. 9600 2. 19200 3. 38400 4. 57600 5.
PAGE 58
Menu Tree MX410/MX412 System Manual C 1. IP Address 6. Network Management 1. Ethernet 1. IP Address Subnet Mask 3. Apply Settings 2. Gateway MAC Address Eth (1 - 4) 3. Link Speed & Duplex Functional Link Speed & Duplex Link Status 1. BCP/IPCP 2. PPP BCP/IPCP PPP (1 - 4) 2. IP Address Subnet Mask Far End IP Address 3. SNMP Link Status Trap LCP Status BCP/IPCP Status 3. DHCP 1. State 2. Network 3. Default Router 4. DNS Router 5. Address Range 6. Lease Time 1. SNMP State 7. SNMP 2. Trap Host 1 IP 3.
PAGE 59
MX410/MX412 System Manual A 1. PPPs 3. Quick Setup 2. V.35 3. FXS (MX412 Only) Menu Tree 1. Choose FROM PPP 2. Choose TO Group 3. Choose TO DS0 Range 4. Apply Cross-Connect 1. Choose TO Group 2. Choose TO DS0 Range 3. Apply Cross-Connect 1. Choose TO Group 2. Choose TO DS0 3. Mode 4. Apply Cross Connect 3. System ID 4. IP Address / Subnet Mask 1. Loop Start 2. PLAR D4 3. PLAR D3 4. FX Ringdown New System Name 1. IP Address New IP Address 2. Subnet Mask New Subnet Mask 3. Apply Settings 5.
PAGE 60
Menu Tree MX410/MX412 System Manual D 5. Test DS1 Ports 1. #1 2. #2 3. #3 4. #4 5. Reset ALL Tests 6. Loopback Timeout 6. Performance Monitoring 7. System Alarms 1. Daily PM Table 2. Quarter Hour PM Table 3. Daily PM Thresholds 4. Quarter Hour PM Thresholds 5. Clear PM Data Execute (Y, N) 9. Pattern Test 1. ES-L Threshold 2. CV-P Threshold (ESF mode) 3. CV-P Threshold (SF mode) 4. ES-P Threshold 5. SES-P Threshold 6. SES-P Threshold 7. CSS-P Threshold 8. UAS-P Threshold 1. Value 2.
PAGE 61
MX410/MX412 System Manual Menu Descriptions MENU DESCRIPTIONS The MX410/MX412 Main Menu (see Figure 5-4) is the access point to all other operations. Each Main menu item has several functions and submenus that identify and provide access to specific operations and parameters.
PAGE 62
Menu Descriptions MX410/MX412 System Manual Configuration Screen The Configuration Screen (see Figure 5-5) displays information about the MX410/MX412. Information such as Code Version changes as upgrades are performed. The CLEI Code and Part Number can be used to search for related information on the ADTRAN website or to order additional parts. Some information from this menu may be required when calling the ADTRAN Technical Support.
PAGE 63
MX410/MX412 System Manual Menu Descriptions Table 5-3. MX410/MX412 Configuration Screen Fields Field Description Unit Name This field displays the MX410/MX412 unit name. CLEI Code This field displays the Common Language Equipment Identifier (CLEI) code of the MX410/MX412. Part Number This field displays the MX410/MX412 part number. Serial Number This field displays the serial number of the MX410/MX412.
PAGE 64
Menu Descriptions MX410/MX412 System Manual Provisioning Menu The Provisioning Menu (see Figure 5-6) is used to make provisioning changes to various options. MX410 Active Alarms: CRITICAL MAJOR MINOR ID: MM/DD/YY HH:MM MX410 Provisioning 1 - DS1 Ports 2 - V.35 Port 3 - Cross-Connect Mapping 4 - Terminal Server Ports 5 6 7 8 9 10 - General Network Management SNMP System Configuration Archive (SCA) Save Provisioning Auto Save : Enabled Selection : '?' - System Help Screen Figure 5-6.
PAGE 65
MX410/MX412 System Manual Menu Descriptions Table 5-4. Provisioning Menu Options Option Description Function 1 DS1 Ports This option displays the “DS1 Ports Menu” on page 5-16. 2 V.35 Port This option displays the “V.35 Port Menu” on page 5-22. 3 Cross-Connect Mapping This option displays the “Cross-Connect Mapping Menu” on page 5-23. 4 Terminal Server Ports This option displays the “Terminal Server Ports Menu” on page 5-25.
PAGE 66
Menu Descriptions MX410/MX412 System Manual DS1 Ports Menu The DS1 Ports Menu (see Figure 5-7) displays line length, line coding, loopback detection, framing, SNMP line status trap, SNMP link status trap, circuit ID, interface state, and alarm pass thru information for DS1 ports 1-4 (1-12 on the MX412), as well as timing information. Selection of an option invokes other menus to set the option variables. The Toggle command can be used to view more DS1 port information shown in Figure 5-8.
PAGE 67
MX410/MX412 System Manual Menu Descriptions The DS1 Ports menu options are shown in Table 5-5. Table 5-5. DS1 Ports Menu Options Option Description Function 1 DS1 Port #1 This option displays the “DS1 Provisioning Menu” on page 5-18. 2 DS1 Port #2 This option displays the “DS1 Provisioning Menu” on page 5-18. 3 DS1 Port #3 This option displays the “DS1 Provisioning Menu” on page 5-18. 4 DS1 Port #4 This option displays the “DS1 Provisioning Menu” on page 5-18.
PAGE 68
Menu Descriptions MX410/MX412 System Manual DS1 Provisioning Menu The DS1 Provisioning menu (see Figure 5-9) is used to set the line length, line coding, loopback detection, framing, SNMP line status trap, SNMP link status trap, circuit ID, interface state, and alarm pass thru information for the selected DS1 port.
PAGE 69
MX410/MX412 System Manual Menu Descriptions Table 5-6. DS1 Provisioning Menu Options Option Description Function 1 Line Length This option sets the line length (line build out) for each port interface according to the distance from the MX410/MX412 to the other device.
PAGE 70
Menu Descriptions MX410/MX412 System Manual Primary Timing Mode Menu The Primary Timing Mode menu (see Figure 5-10) is used to set the primary timing mode for the selected DS1 port (1-4 on the MX410 and 1-12 on the MX412). MX410 Active Alarms: CRITICAL MAJOR ID: MM/DD/YY HH:MM MX410 Primary Timing Mode : Internal 1 2 3 4 5 - Internal DS1 1 DS1 2 DS1 3 DS1 4 Selection : '?' - System Help Screen Figure 5-10. Primary Timing Mode Menu The Primary Timing Mode menu options are shown in Table 5-7.
PAGE 71
MX410/MX412 System Manual Menu Descriptions Secondary Timing Mode Menu The Secondary Timing Mode menu (see Figure 5-11) is used to set the secondary timing mode for the selected DS1 port (1-4 on the MX410 and 1-12 on the MX412). MX410 Active Alarms: CRITICAL MAJOR ID: MM/DD/YY HH:MM MX410 Primary Timing Mode : Internal 1 2 3 4 5 - Internal DS1 1 DS1 2 DS1 3 DS1 4 Selection : '?' - System Help Screen Figure 5-11.
PAGE 72
Menu Descriptions MX410/MX412 System Manual V.35 Port Menu The V.35 Port Menu (see Figure 5-12) is used to provision the V.35 Port. MX410 Active Alarms: CRITICAL ID: MM/DD/YY HH:MM MX410 V.35 Port 1 - CTS 2 - DCD 3 - DSR : Forced On : Forced On : Normal Selection : '?' - System Help Screen Figure 5-12. V.35 Port Menu The V.35 Port menu options are shown in Table 5-9. Table 5-9. V.35 Port Menu Options Option 1 Description Function CTS This option sets the CTS (Clear To Send) settings.
PAGE 73
MX410/MX412 System Manual Menu Descriptions Cross-Connect Mapping Menu The Cross-Connect Mapping menu is used to display DS0 information for the four DS1 ports (12 ports on the MX412), as well as FXS (MX412 only), PPP, and V.35 settings. The CrossConnect Mapping menu is shown in Figure 5-13 displaying DS0 mapping for the DS1 1 port. The Toggle command is used to view DS1 2, DS1 3, DS1 4, PPP, and V.35 data.
PAGE 74
Menu Descriptions MX410/MX412 System Manual The Cross-Connect Mapping menu options are shown in Table 5-10. Table 5-10. Cross-Connect Mapping Menu Options Option 1-24 Description Function DS0 1-24 connections These options invoke the Change Cross-Connect Mapping menu which is used to provision the cross-connect settings for the selected DS1 port. Options are as follows: • 1. Choose TO Group (for DS1 1 through DS1 4/DS1 12) • 2. Choose TO DS0: (enter a value) • 3.
PAGE 75
MX410/MX412 System Manual Menu Descriptions Terminal Server Ports Menu The Terminal Server Ports Menu (see Figure 5-15) is used to select Terminal Port 1 through Port 4 for provisioning. MX410 Active Alarms: CRITICAL ID: MM/DD/YY HH:MM MX410 Terminal Server Ports 1 2 3 4 Selection : - Port Port Port Port 1 2 3 4 '?' - System Help Screen Figure 5-15. Terminal Server Ports Menu The Terminal Server Ports menu options are shown in Table 5-11. Table 5-11.
PAGE 76
Menu Descriptions MX410/MX412 System Manual Terminal Server Port (1 - 4) Menu The Terminal Server Port Menu (see Figure 5-16) is used to provision the Terminal Sever Port selected on the (previous) Terminal Server Ports menu. MX410 Active Alarms: CRITICAL ID: MM/DD/YY HH:MM MX410 Terminal Server Port 1 1 2 3 4 5 6 - Terminal State Baud Rate Telnet Port Number Security Username Password Selection : : : : : : : Enabled 9600 2023 Enabled port 1 password '?' - System Help Screen Figure 5-16.
PAGE 77
MX410/MX412 System Manual Menu Descriptions General Provisioning Menu The General Provisioning Menu (see Figure 5-17) is used to provision the craft port Baud rate, the date, time, system ID, auto-logoff inactivity time, to reset the MX410/MX412, and to handle security administration.
PAGE 78
Menu Descriptions MX410/MX412 System Manual Table 5-13. General Provisioning Menu Options (Continued) Option 5 Description Function Auto-Logoff Inactivity Time This option defines when a menu session automatically terminates due to inactivity. The default setting is 15 Minutes. Options are as follows: • 120 Minutes • 90 Minutes • 60 Minutes • 30 Minutes • 15 Minutes • 10 Minutes • 5 Minutes • Disabled 6 Card Reset This option forces the MX410/MX412 to reset.
PAGE 79
MX410/MX412 System Manual Menu Descriptions Network Management Menu The Network Management menu (see Figure 5-18) is used to provision network information. MX410 Active Alarms: CRITICAL MAJOR ID: MM/DD/YY HH:MM MX410 Network Management 1 - Ethernet 2 - PPP BCP/IPCP 3 - DHCP Selection : '?' - System Help Screen Figure 5-18. Network Management Menu The Network Management menu options are shown in Table 5-14. Table 5-14.
PAGE 80
Menu Descriptions MX410/MX412 System Manual Ethernet Menu The Ethernet Menu (see Figure 5-19) is used to provision Ethernet information. MX410 Active Alarms: CRITICAL ID: MM/DD/YY HH:MM MX410 Ethernet 1 - IP Address Subnet Mask 2 - Gateway MAC Address : : : : 192.168.100.1 255.255.0.0 192.168.1.1 XX:XX:XX:XX:XX:XX Eth 1 3 - Link Speed & Duplex : Auto Functional Link Speed & Duplex : Unknown Link Status : Down (T)oggle Between Interfaces Selection : '?' - System Help Screen Figure 5-19.
PAGE 81
MX410/MX412 System Manual Menu Descriptions Table 5-15. Ethernet Menu Options (Continued) Option Description Function MAC Address This read-only field displays the Medium Access Control (MAC) Address. MAC Addresses are location-independent (programmed into the card at manufacture, they relocate when the card does). MAC Addresses are contained in the headers of packets and are used to filter and forward packets.
PAGE 82
Menu Descriptions MX410/MX412 System Manual PPP BCP/IPCP Menu Point-to-Point Protocol (PPP) is commonly used for LAN extension and Remote management connectivity. PPP can use one of two upper layer protocols: • BCP (Bridge Control Protocol): This protocol routes packets based on MAC addresses and allows broadcast traffic to be passed over the PPP link(s). This protocol enables true LAN Extension to be completed.
PAGE 83
MX410/MX412 System Manual Menu Descriptions Table 5-16. PPP BCP/IPCP Menu Options Option Description Function 1 BCP/IPCP This option is used to select either BCP (Bridge Control Protocol) or IPCP (IP Control Protocol for routing). IP Address This option invokes another menu which is used to enter the IP Address, the Subnet Mask for the PPP. The IP Address is written in the format XXX.XXX.XXX.XXX, where each 3-digit field has a value between 1 and 255.
PAGE 84
Menu Descriptions MX410/MX412 System Manual DHCP Server Menu The DHCP (Dynamic Host Configuration Protocol) Server menu shown in Figure 5-21, is used to provision DHCP server connections. MX410 Active Alarms: CRITICAL MAJOR ID: MM/DD/YY HH:MM MX410 DHCP Server 1 2 3 4 5 6 - State Network Default Router DNS Router Address Range Lease Time (d:h:m) Selection : : : : : : : Disabled Not Set/Not Set Not Set Not Set 0.0.0.0-255.255.255.255 0:0:0 '?' - System Help Screen Figure 5-21.
PAGE 85
MX410/MX412 System Manual Menu Descriptions SNMP Menu The SNMP (Simple Network Management Protocol) menu (see Figure 5-22) is used to provision SNMP information. MX410 Active Alarms: CRITICAL MAJOR MINOR ID: MM/DD/YY HH:MM MX410 SNMP 1 2 3 4 5 6 7 8 9 10 11 - SNMP State Trap Host 1 IP Trap Host 2 IP Trap Host 3 IP Trap Host 4 IP SNMP Traps System Name System Location System Contact Read Community Write Community : : : : : : : : : : : Disabled 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.
PAGE 86
Menu Descriptions MX410/MX412 System Manual Table 5-18. SNMP Menu Options (Continued) Option Description Function 5 Trap Host 4 IP This option invokes another menu which is used to enter the Trap Host 4 IP address of an SNMP manager to which the MX410/ MX412 sends traps, the method (version 1 traps or version 2 notifications), and enable or disable the trap host.
PAGE 87
MX410/MX412 System Manual Menu Descriptions SCA Update Menu The SCA (System Configuration Archive) Update Menu (see Figure 5-23) is used to update SCA information. MX410 Active Alarms: CRITICAL MAJOR ID: MM/DD/YY HH:MM MX410 SCA Update 1 2 3 4 5 - SCA TFTP Server : 0.0.0.0 Remote Filename : All/Data Path Only : All Provisioning Perform SCA Save Perform SCA Restore 6 - Auto Save Time 7 - Auto Save : Wed 10:35 : Disabled Awaiting download. Selection : '?' - System Help Screen Figure 5-23.
PAGE 88
Menu Descriptions MX410/MX412 System Manual Quick Setup Menu To simplify the installation process, all of the basic configuration options necessary to setup the MX410/MX412 are grouped together on the Quick Setup menu (see Figure 5-24). The Quick Setup menu allows configuration of such items as DS0 drop assignments, as well as system date, time, and IP Address information. MX410 Unacknowledged Alarms: CRITICAL ID: MM/DD/YY HH:MM MX410 Quick Setup Ports 1 - PPPs PPP 1 2 - V.
PAGE 89
MX410/MX412 System Manual Menu Descriptions Table 5-20. Quick Setup Menu Options (Continued) Option 3 Description Function FXS (MX412 only) This option is used to provision the FXS port. Options are as follows: • Choose TO Group (for DS1 1 through DS1 4) • Choose TO DS0 Range: enter a range • Mode: Select Loop Start, PLAR D4, PLAR D3, or FX Ringdown. Refer to Table 4-6 on page 4-9 for descriptions of these options.
PAGE 90
Menu Descriptions MX410/MX412 System Manual Status Screen The Status screen (see Figure 5-25) provides detailed status information about the DS1 Ports, Ethernet Ports, PPP, Timing, and the Power Feed.
PAGE 91
MX410/MX412 System Manual Menu Descriptions Table 5-21. Status Screen Fields (Continued) Option Description Function Test This field displays one of the following possible states: • Data Mode: Indicates no tests are active • Payload Loopback: Indicates that a payload loopback is in progress • Line Loopback: Indicates that a line loopback is in progress PPP Interfaces 1-4 State This field displays the current state of the four PPP interfaces as either Enabled or Disabled.
PAGE 92
Menu Descriptions MX410/MX412 System Manual Test Menu The Test menu (see Figure 5-26) provides options for testing the DS1 Ports. MX410 Active Alarms: CRITICAL MAJOR ID: MM/DD/YY HH:MM MX410 Test DS1 Ports 1 2 3 4 - #1 #2 #3 #4 : : : : Pattern Data mode Data mode Data mode 5 - Reset ALL Tests 6 - Loopback Timeout: Selection : 120 Minutes '?' - System Help Screen Figure 5-26. Test Menu The Test menu options are shown in Table 5-22. Table 5-22.
PAGE 93
MX410/MX412 System Manual Menu Descriptions DS1 (Port #) Menu The DS1 (Port #) menu (see Figure 5-27) provides options for testing the DS1 Ports. MX410 Active Alarms: CRITICAL MAJOR ID: MM/DD/YY HH:MM MX410 DS1 1 1 - Loopback : Pattern Pattern : Ones 2 - Insert One Bit Error 3 - Clear Bit Error Count Patt Sync : NO SYNC Bit Errors : 14 DS1 1 Status Selection: : LOS,TX RAI '?' - System Help Screen Figure 5-27. DS1 (Port #) Menu The DS1 (Port #) menu options are shown in Table 5-23. Table 5-23.
PAGE 94
Menu Descriptions MX410/MX412 System Manual Port (#) Test Menu The Port (#) Test menu (see Figure 5-28) provides options for testing the DS1 Ports. MX410 Active Alarms: CRITICAL MAJOR ID: MM/DD/YY HH:MM MX410 Port #1 : Pattern 1 2 3 4 5 6 7 8 9 Selection: - Data Mode Payload Line Inward Dual Remote FDL Line Remote Inband Line (CSU) Remote FDL Payload Pattern Test '?' - System Help Screen Figure 5-28.
PAGE 95
MX410/MX412 System Manual Menu Descriptions DS1 Test Pattern Menu The DS1 Test Pattern menu (see Figure 5-29) provides options for testing the DS1 ports using pattern data. MX410 Active Alarms: CRITICAL MAJOR ID: MM/DD/YY HH:MM MX410 DS1 1 Test Pattern 1 2 3 4 5 6 7 Selection : - QRSS All Ones All Zeros 511 2047 2^15-1 2^20-1 '?' - System Help Screen Figure 5-29. DS1 Test Pattern Menu The DS1 Test Pattern menu options are all test pattern types.
PAGE 96
Menu Descriptions MX410/MX412 System Manual Performance Monitoring Menu The Performance Monitoring menu (see Figure 5-30) provides options for viewing performance data affecting the MX410/MX412 operations. Data is viewed in daily or 15-minute increments. MX410 Active Alarms: CRITICAL MAJOR ID: MM/DD/YY HH:MM MX410 Performance Monitoring 1 2 3 4 5 - Daily PM Table Quarter Hour PM Table Daily PM Thresholds Quarter Hour PM Thresholds Clear PM Data Selection : '?' - System Help Screen Figure 5-30.
PAGE 97
MX410/MX412 System Manual Menu Descriptions Table 5-26. Performance Monitoring Definitions T1 PM Parameter Definition Description CV-L Code Violation - Line This parameter indicates the number of Bipolar Violations (BPVs) and Excessive Zeros (EXZs) that have occurred during the accumulation period. ES-L Errored Seconds - Line This parameter indicates the number of seconds for which one or more Line Coding Violations (CV-Ls), or one or more Loss of Signal (LOS) defects occurred.
PAGE 98
Menu Descriptions MX410/MX412 System Manual Daily Performance Monitoring Screen The Daily Performance Monitoring screen (see Figure 5-31) displays DS1 performance monitoring data in daily increments and in a tabular format.
PAGE 99
MX410/MX412 System Manual Menu Descriptions Daily PM Thresholds Menu The Daily PM Thresholds menu (see Figure 5-33) displays DS1 performance monitoring thresholds data in a tabular format. This menu is used to set the performance monitoring threshold levels and enable or disable an alarms if the threshold is exceeded.
PAGE 100
Menu Descriptions MX410/MX412 System Manual Table 5-27. Daily PM Thresholds Menu Options (Continued) Option Description Function 8 UAS-P This option sets the UAS-P threshold value. The available threshold range is (1-65535). The default value is 10. 9 Restore ALL DS1 Threshold Defaults This option restores all threshold values to the defaults listed above. 10 Enable ALL DS1 Threshold Alarms This option enables all daily threshold alarms.
PAGE 101
MX410/MX412 System Manual Menu Descriptions Quarter Hour PM Thresholds Menu The Quarter Hour PM Thresholds menu (see Figure 5-34) displays DS1 performance monitoring thresholds data in a tabular format. This menu is used to set the performance monitoring threshold levels and enable or disable an alarms if the threshold is exceeded.
PAGE 102
Menu Descriptions MX410/MX412 System Manual Table 5-28. Quarter Hour PM Thresholds Menu Options (Continued) Option Description Function 8 UAS-P This option sets the UAS-P threshold value. The available threshold range is (1-900). The default value is 10. 9 Restore ALL DS1 Threshold Defaults This option restores all threshold values to the defaults listed above. 10 Enable ALL DS1 Threshold Alarms This option enables all quarter hour threshold alarms.
PAGE 103
MX410/MX412 System Manual Menu Descriptions System Alarms Menu The System Alarms Menu (see Figure 5-35) provides options for viewing all alarms affecting MX410/MX412 system operations. Alarms may be viewed within the Master Log menu (detailed in the next section). The Environmental Alarms menu contains provisionable options. The Alarm Chronology menu offers the viewing of alarms in either ascending or descending order.
PAGE 104
Menu Descriptions MX410/MX412 System Manual Master Log Menu The Master Log Menu (see Figure 5-36) is used to review and acknowledge alarms.
PAGE 105
MX410/MX412 System Manual Menu Descriptions Code Download Method Menu The Code Download Method menu (see Figure 5-37) provides options for upgrading the software of the MX410/MX412. MX410 Active Alarms: CRITICAL ID: MM/DD/YY HH:MM MX410 Code Download Method 1 - X-MODEM 2 - TFTP Selection : '?' - System Help Screen Figure 5-37. Code Download Method Menu The Code Download Method menu options are shown in Table 5-29. Table 5-29.
PAGE 106
Menu Descriptions MX410/MX412 System Manual This page is intentionally blank.
PAGE 107
Appendix A Warranty WARRANTY AND CUSTOMER SERVICE ADTRAN will replace or repair this product within the warranty period if it does not meet its published specifications or fails while in service. Warranty information can be found at www.adtran.com/warranty. Refer to the following subsections for sales, support, Customer and Product Service (CAPS) requests, or further information.
PAGE 108
® Carrier Networks Division 901 Explorer Blvd.