Specifications

ManualsBrandsADTRAN ManualsNetwork RouterMX410

MX410/MX412

System Manual

Document Number: 61189500L1-1F

September 2010

Summary of content (134 pages)

PAGE 1
® MX410/MX412 System Manual Document Number: 61189500L1-1F September 2010
PAGE 2
MX410/MX412 System Manual Trademarks Front Matter Any brand names and product names included in this manual are trademarks, registered trademarks, or trade names of their respective holders. To the Holder of the Manual The contents of this publication are current as of the date of publication. ADTRAN® reserves the right to change the contents without prior notice.
PAGE 3
Revision History Revision Date Description of Changes A June 2005 B September 2005 PPP and MX412 information added C December 2005 Primary Timing, Secondary Timing, and Cross-connect defaults changed D October 2006 E September 2007 F August 2010 Initial release Frame Relay added Additional Status and Performance Monitoring functionality added. Example Data from PM Flat File Updated (Table 5-40).
PAGE 4
MX410/MX412 System Manual HAZARD CLASSIFICATIONS The following hazard classifications are used in this document: NOTE Notes inform the user of additional, but essential, information or features. CAUTION Cautions inform the user of potential damage, malfunction, or disruption to equipment, software, or environment. WARNING Warnings inform the user of potential bodily pain, injury, or death.
PAGE 5
Training ADTRAN offers training courses on our products. These courses include overviews on product features and functions while covering applications of ADTRAN product lines. ADTRAN provides a variety of training options, including customized training and courses taught at our facilities or at customer sites. For inquiries concerning training, contact ADTRAN: Training Phone: 800-615-1176, ext. 6303 Training Fax: 256-963-6217 Training Email: training@adtran.
PAGE 6
MX410/MX412 System Manual vi 61189500L1-1F
PAGE 7
Contents Hazard Classifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-iv Section 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Features . . . . .
PAGE 8
MX410/MX412 System Manual Rackmount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2 Wallmount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2 Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 9
Contents Network Management Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ethernet Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PPP BCP/IPCP Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DHCP Server Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 10
MX410/MX412 System Manual Figures Figure 1-1. Figure 1-2. Figure 1-3. Figure 1-4. Figure 3-1. Figure 3-2. Figure 3-3. Figure 3-4. Figure 3-5. Figure 3-6. Figure 3-7. Figure 3-8. Figure 3-9. Figure 3-10. Figure 3-11. Figure 3-12. Figure 3-13. Figure 3-14. Figure 3-15. Figure 3-16. Figure 3-17. Figure 3-18. Figure 3-19. Figure 3-20. Figure 3-21. Figure 3-22. Figure 3-23. Figure 3-24. Figure 4-1. Figure 4-2. Figure 4-3. Figure 4-4. Figure 4-5. Figure 4-6. Figure 5-1. Figure 5-2. Figure 5-3. Figure 5-4.
PAGE 11
Figures Figure 5-12. Figure 5-13. Figure 5-14. Figure 5-15. Figure 5-16. Figure 5-17. Figure 5-18. Figure 5-19. Figure 5-20. Figure 5-21. Figure 5-22. Figure 5-23. Figure 5-24. Figure 5-25. Figure 5-26. Figure 5-27. Figure 5-28. Figure 5-29. Figure 5-30. Figure 5-31. Figure 5-32. Figure 5-33. Figure 5-34. Figure 5-35. Figure 5-36. Figure 5-37. Figure 5-38. Figure 5-39. Figure 5-40. Figure 5-41. Figure 5-42. Figure 5-43. Figure 5-44. Figure 5-45. Figure 5-46. Figure 5-47. Figure 5-48. Figure 5-49.
PAGE 12
MX410/MX412 System Manual Tables Table 2-1. Table 2-2. Table 2-3. Table 2-4. Table 2-5. Table 3-1. Table 3-2. Table 3-3. Table 3-4. Table 4-1. Table 4-2. Table 4-3. Table 4-4. Table 4-5. Table 4-6. Table 4-7. Table 5-1. Table 5-2. Table 5-3. Table 5-4. Table 5-5. Table 5-6. Table 5-7. Table 5-8. Table 5-9. Table 5-10. Table 5-11. Table 5-12. Table 5-13. Table 5-14. Table 5-15. Table 5-16. Table 5-17. Table 5-18. Table 5-19. Table 5-20. Table 5-21. Table 5-22. Table 5-23. Table 5-24. Table 5-25. Table 5-26.
PAGE 13
Tables Table 5-30. Table 5-31. Table 5-32. Table 5-33. Table 5-34. Table 5-35. Table 5-36. Table 5-37. Table 5-38. Table 5-39. Table 5-40. Table 5-41. Table 5-42. Status Screen Fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-55 Test Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-58 DS1 (Port #) Menu Options . . . . . . . . . . . . . . . . . .
PAGE 14
MX410/MX412 System Manual xiv 61189500L1-1F
PAGE 15
Section 1 Introduction OVERVIEW The MX410 (P/N 1189500L1) and MX412 (P/N 1189512L1) systems deliver full DS0 control to service locations, allowing carriers full use of DS1 bandwidth. The MX410 (see Figure 1-1) interfaces to four long-haul outside plant protected DS1s by way of RJ-48 connectors, while the MX412 (see Figure 1-2) interfaces to 12 DS1s. Data and management on the DS1s can be cross connected on a non-blocking per-DS0 basis to any DS1, V.35 port, and four PPP ports.
PAGE 16
MX410/MX412 System Manual Digital Radios Data Analog Radios Data Grooming of DS0s LAN Extension over PPP for Remote Management Star Configuration of Backhaul Backhaul 4 x DS1 (I/O) Battery Backup HVAC Backhaul Radio Management 4 x RS-232 V.35 Redundant Power Capability DB-9 Craft Interface E911, etc. 4 x 10/100 Ethernet Figure 1-3.
PAGE 17
Features FEATURES The major features of the MX410/MX412 are as follows: • 19-inch wall mounting or rack mounting, one rack unit high • Front panel data connections • One V.35 port • Four RJ-45 long-haul DS1 connections (12 on the MX412) with outside plant protection • A four-port Ethernet switch • Non-blocking DS0 cross connect between all DS1 interfaces and the V.
PAGE 18
MX410/MX412 System Manual This page is intentionally blank.
PAGE 19
Section 2 Engineering Guidelines GENERAL This section provides engineering guidelines for network designers who are incorporating an MX410/MX412 into their network. COMPLIANCE The MX410/MX412 complies with the requirements covered under UL 60950 and NEBS Level 3. The MX410/MX412 is intended to be installed in a restricted access area only. The MX410/MX412 complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. The device may not cause harmful interference. 2.
PAGE 20
MX410/MX412 System Manual Table 2-1. MX410 and MX412 Configuration Codes Code Input Output Power Code (PC) F C Telecommunication Code (TC) X X Installation Code (IC) A – Table 2-2.
PAGE 21
Power Dissipation POWER DISSIPATION Table 2-5 provides the heat dissipation data at –48 VDC (operating range of –42 VDC to –60 VDC) and ±24 VDC (operating range of ±22 VDC to ±27 VDC) with redundant PSUs installed (MX410 only). Table 2-5. Heat Dissipation at –48 VDC and ±24 VDC Part Number Equipment Heat Dissipation at –48 VDC Heat Dissipation at ±24 VDC 1189500L1 MX410 11.8 watts 10.5 watts 1189512L1 MX412 17.3 watts 18.
PAGE 22
MX410/MX412 System Manual This page is intentionally blank.
PAGE 23
Section 3 Application Guidelines INTRODUCTION This section describes several applications for the MX410/MX412 system. For each application there is a figure illustrating the application, a list of the equipment needed, and an explanation of the basic setup.
PAGE 24
MX410/MX412 System Manual MX410 DATA PATH BLOCK DIAGRAM As shown in Figure 3-1, the MX410 contains a 1/0 cross connect that allows DS0s to be mapped between four DS1s (twelve DS1s on the MX412), four PPP ports, and a V.35 port. Refer to “PPP BCP/IPCP Menu” on page 5-38 for more information about using PPP. Any DS0 in DS1 1 can be mapped to any DS0 in DS1 1-4, any PPP port, or the V.35 port. Any unmapped DS0 in a DS1 is filled with all ones. Therefore, if an entire T1 is unmapped, framed all ones are sent.
PAGE 25
MX410 Data Path Block Diagram Drop and Continue Application The following applies to Remote Site #1 shown in Figure 3-2. In the Drop and Continue Application, any combination of DS0s from one DS1 can be dropped out the other DS1 ports with the remaining DS0s continuing through to the other DS1 interface. This enables the bandwidth of one DS1 to deliver DS0s to several sites using one MX410 at each site.
PAGE 26
MX410/MX412 System Manual Setup Connect the incoming DS1 (the DS1 from which the DS0s are dropped) to the DS1 1 RJ Connector. Connect the outgoing DS1 to the DS1 2 RJ Connector. Connect the other DS1s using the RJ connector on the front panel. For more information, refer to “DS1 Ports” on page 4-6. Starting from the default mapping, the DS0s can be dropped using the Quick Setup menu to the PPP and V.35 ports (see Figure 3-3). Select each port (PPP1-4, V.
PAGE 27
MX410 Data Path Block Diagram Figure 3-4 shows the Quick Setup menu after DS0s 21-22 have been dropped from DS1 1 to PPP1, DS0s 23-24 have been dropped from DS1 1 to the V.35 port. MX410 MINOR Active Alarms: CRITICAL MM/DD/YY HH:MM MX410 ID: Quick Setup Ports 1 - PPPs PPP 1 = DS1 1 DS0 #21-22 2 - V.35 = DS1 1 DS0 #23-24 System 3 - System ID 4 - IP Address Subnet Mask 5 - Default Gateway 6 - Date 7 - Time : 192.168.100.1 : 255.255.0.0 : 192.168.1.
PAGE 28
MX410/MX412 System Manual Figure 3-6 shows the Cross-Connect Mapping menu after the remaining DS0s have been continued to DS1 2 as well as four DS0s (13-16) dropped to DS1 3 (1-4) and four other DS0s (17-20) dropped to DS1 4 (1-4).
PAGE 29
MX410 Data Path Block Diagram Drop and Insert Application The following applies to Remote Site #1 shown in Figure 3-7. In the Drop and Insert Application DS0s from one DS1 can be dropped out to the other DS1 ports. Then DS0s from the other DS1 ports can be inserted into the corresponding DS0s in the other DS1. In the example shown, any DS0 not dropped will be mapped to continue on from one DS1 to another. This allows a DS1 to be used to transport DS0s between several sites.
PAGE 30
MX410/MX412 System Manual Setup Connect the DS1 from which the DS0s will be dropped to the DS1 1 RJ. Connect the other DS1 to which the DS0s will be inserted to the DS1 2 RJ. Connect the other DS1s using the other RJ connectors on the front panel. For more information, refer to “DS1 Ports” on page 4-6 Starting from the default mapping the DS0s can be dropped and inserted using the Quick Setup menu (see Figure 5-39 on page 5-52). Select each port (PPP or V.
PAGE 31
MX410 Data Path Block Diagram Figure 3-9 shows the Quick Setup menu after DS0s 23-24 have been dropped from DS1 1 to PPP1 and PPP 2 has been inserted into DS0s 23-24 in DS1 2. MX410 MINOR Active Alarms: CRITICAL MM/DD/YY HH:MM MX410 ID: Quick Setup Ports 1 - PPPs PPP 1 = DS1 1 DS0 #23-24 PPP 2 = DS1 2 DS0 #23-24 2 - V.35 = DS1 1 DS0 #23-24 System 3 - System ID 4 - IP Address Subnet Mask 5 - Default Gateway 6 - Date 7 - Time : 192.168.100.1 : 255.255.0.0 : 192.168.1.
PAGE 32
MX410/MX412 System Manual Figure 3-11 shows the Cross-Connect Mapping menu after DS0s 1-12 are continued through from DS1 1 to DS1 2 and DS0s 13-22 are dropped from DS1 1 to DS1 3.
PAGE 33
MX410 Data Path Block Diagram Figure 3-13 shows the Cross-Connect Mapping menu after DS0s 13-22 are inserted in DS1 2 from DS1 4. Any unmapped DS0s will be filled with all ones.
PAGE 34
MX410/MX412 System Manual Integrated Wireless Access Device or DS0 Grooming The following applies to Remote Site #1 shown in Figure 3-14 and Figure 3-15. In the Integrated Wireless Access Device Application, bandwidth is conserved by using the MX410 to groom multiple fractional T1s into a single T1. This allows the MX410 to be used as an integrated wireless access device (see Figure 3-14) or to transport DS0s between several sites (see Figure 3-15).
PAGE 35
MX410 Data Path Block Diagram DS1 Central Site 24 DS0s from Central Site DS1 DS1 µ Wave/ Leased DS1 Drop DS0s to/from Local Equipment ETH1 Drop DS0s to PPP to Control Local Equipment via Ethernet. Drop DS0s to PPP to Control Local Equipment via Ethernet DS1 µ Wave/ Leased DS1 DS1 DS1 µ Wave/ Leased DS1 Switch Drop DS0s to/from Local Equipment Original DS0s Continue Downstream; All Ones in Unmapped DS0s Insert DS0s from PPP to Continue Ethernet Path Conserving Bandwidth DS1 ETH1 V.
PAGE 36
MX410/MX412 System Manual Setup Connect the DS1 from which the DS0s will be dropped to the DS1 1 RJ Connector. Connect the other DS1s to DS1, 2, 3, and 4 RJ Connectors. For more information, refer to “DS1 Ports” on page 4-6. Starting from the default mapping the DS0s can be mapped using the Quick Setup menu shown in Figure 3-16. Select each port to which a DS0 needs to be dropped from the incoming DS1. For each port select the DS0(s) in DS1 1 to be dropped to that port.
PAGE 37
MX410 Data Path Block Diagram Figure 3-17 shows the Quick Setup menu after DS0s 23-24 have been dropped from DS1 1 to PPP1, and PPP 2, 3, and 4 have been inserted into DS0s 23-24 in DS1 2, 3, and 4, respectively. PPP 2, 3, and 4 are typically not used in this fashion for the integrated wireless access device application. MX410 MINOR Active Alarms: CRITICAL MM/DD/YY HH:MM MX410 ID: Quick Setup Ports 1 - PPPs PPP 1 PPP 2 PPP 3 PPP 4 2 - V.
PAGE 38
MX410/MX412 System Manual Figure 3-19 shows the Cross-Connect Mapping menu after DS0s 1-7 are mapped from DS1 1 to DS1 2, DS0s 8-14 are mapped from DS1 1 to DS1 3, and DS0s 15-22 are mapped from DS1 1 to DS1 4.
PAGE 39
MX410 Data Path Block Diagram Figure 3-21 shows the Cross-Connect Mapping menu for DS1 3.
PAGE 40
MX410/MX412 System Manual Remote Management of Other Systems using Terminal Server Ports and Ethernet Connectivity In this application, the Terminal Server ports on the MX410 are used to provide remote management of other non-Ethernet based equipment at the same site. This requires connecting the RS-232 craft ports of the other equipment to the Terminal Server ports of the MX410. Establishing a Telnet session to the MX410 Terminal Server ports establishes access to the other equipment.
PAGE 41
MX410 Data Path Block Diagram Setup First, connect the RS-232 craft port on the other equipment to the MX410 terminal server port. For more information, refer to “Terminal Server Ports” on page 4-8. The default settings for the terminal server ports are 9600 bps and 8 data bits with no parity (see Figure 3-24). These settings must match the craft port settings of the other equipment for the application to work. Baud Rate can be changed in the MX410 Terminal Server menus under Provisioning.
PAGE 42
MX410/MX412 System Manual This page is intentionally blank.
PAGE 43
Section 4 Installation GENERAL The first three tasks for installing and operating the MX410/MX412 are to unpack, inspect, and install. Those tasks are detailed in this section of the manual, as well as information for mounting the MX410/MX412 into an equipment rack or to a wall, making the proper connections to the front and rear panels, identifying the front panel indicators, and adding or removing a Power Supply Unit (PSU). NOTE The PSU (P/N 1189501L1) is only available for the MX410.
PAGE 44
MX410/MX412 System Manual RACKMOUNT For a rackmount installation, perform the following steps: 1. Ensure the mounting brackets to the MX410/MX412 are attached using the two screws provided for each bracket. • For 19-inch rack applications, attach the brackets with the short flange parallel with the front of the chassis (see Figure 4-1). • For 23-inch rack applications, attach the brackets with the short flange parallel with the front of the chassis and obtain 23-inch adapter mounting hardware. 2.
PAGE 45
Rear Panel REAR PANEL The MX410/MX412 rear panel is equipped with wire-wrap pins for external auxiliary inputs, wire-wrap pins for alarms (critical, major, and minor), a frame ground lug, and a single power connector for both DC power feeds (A and B). Figure 4-2 illustrates the rear panel. Figure 4-2. MX410/MX412 Rear Panel WARNING The alarm interfaces and AUX inputs must not be metallically connected to interfaces which connect to the Outside Plant or its wiring.
PAGE 46
MX410/MX412 System Manual Alarm Contacts/Auxiliary Inputs The alarm contacts and auxiliary (AUX) inputs are shown in Figure 4-4. Figure 4-4. Alarm Contacts and AUX Inputs The alarm interfaces connect to the nine Form C type relays on the MX410/MX412 labeled CRIT (Critical), MAJOR, and MINOR. Both NC (Normally Closed) and NO (Normally Open) contacts are provided.
PAGE 47
Front Panel FRONT PANEL The front panels for the MX410 and MX412 are described below. MX410 The MX410 front panel (see Figure 4-5) is equipped with the following: • One V.35 Port (refer to “V.
PAGE 48
MX410/MX412 System Manual V.35 Port The V.35 port is a Nx64k serial interface (up to 1.536 Mbps) with a CCITT V.35, 34-pin connector. The pin assignments for the V.35 connector are listed in Table 4-2. Table 4-2. V.
PAGE 49
Front Panel Ethernet Ports The four Ethernet jacks, labeled ETHERNET, are located on the MX410/MX412 front panel. They provide LAN access to the network. From these ports, devices located on the local area network can be remotely managed. The Ethernet ports have automatic rate detection and perform MDI/MDI-X crossover detection eliminating the need for a crossover cable. The Ethernet ports can be accessed using a standard CAT 5 cable with an RJ-45 connector.
PAGE 50
MX410/MX412 System Manual Terminal Server Ports The four Terminal Server port RS-232 interfaces located on the front panel are used to remotely connect to RS-232 managed devices. CAUTION The 8-pin modular Terminal Server Port 1-4 jacks should never be connected to a telecommunications network and are intended for connection to RS-232 data interfaces only. The Terminal Server ports are accessed by establishing a Telnet session to the MX410/MX412 with the TCP Port Number of the particular port.
PAGE 51
Front Panel FXS Port The FXS port (MX412 only) provides a 2-wire analog interface between a Voice Frequency (VF) transmission and a signaling facility. The FXS interface provides for simultaneous signaling in each direction for use with 2-wire off-premises station lines, carrier extended PBX trunks, or subscriber line foreign exchanges using a loop start signaling system. FXS options are listed in Table 4-6. Table 4-6. FXS Options Mode Description Loop Start Selects ANSI T1.
PAGE 52
MX410/MX412 System Manual LED Indicators The LEDs on the front panel of the MX410/MX412 indicate the status of the power, DS1, Ethernet, and alarm interfaces. See Table 4-7 for a listing of the LEDs and their indications. Table 4-7.
PAGE 53
Turn-up TURN-UP The following sections provide turn-up steps for applying power and logging in to the MX410/ MX412. Power Up To power up the MX410/MX412, perform the following steps: 1. Connect the MX410/MX412 to a reliably grounded –48 VDC or ±24 VDC source, which is electrically isolated from the AC source. NOTE A readily accessible disconnect device, such as a rackmount fuse and alarm panel that is suitably approved and rated should be incorporated into the fixed wiring.
PAGE 54
MX410/MX412 System Manual • –48 VDC systems: –42 VDC to –60 VDC • –24 VDC systems: –22 VDC to –27 VDC • +24 VDC systems: +22 VDC to +27 VDC Place the common (normally black) lead of the voltmeter on the RET A post of the DC power terminal block and the DC volts (normally red) lead on the PWR A post of the DC power terminal block. c. Repeat step 3 for the RET B/PWR B connections. 4. Install at least one PSU into the MX410 front panel PSU A or PSU B slot. a.
PAGE 55
Section 5 User Interface INTRODUCTION This section provides detailed information on the following: • “System Management” on page 5-1 • “Logging on to the MX410/MX412” on page 5-2 • “Menu Structure” on page 5-3 • “Menu Layout and Navigation” on page 5-4 • “Menu Trees” on page 5-5 • “Menu Descriptions” on page 5-15 SYSTEM MANAGEMENT MX410/MX412 management and provisioning is facilitated by a series of intuitive menus that are accessible on a computer screen.
PAGE 56
MX410/MX412 System Manual - No parity (none) - One stop bit - No flow control 2. Set the PC for direct connect on the appropriate communications port (as opposed to dial up connection). 3. Plug the male end of the data cable into the MX410/MX412. Make connection to the PC or laptop as appropriate for the equipment. Telnet Session To access the MX410/MX412, use an appropriate Telnet client to access the management interface of the MX410/MX412 at the configured IP address.
PAGE 57
Menu Structure MENU STRUCTURE The menu structure for the MX410/MX412 is a layered menu tree. Each layer of the menu tree is displayed as a menu or a screen. This section defines the terminology used in conjunction with the MX410/MX412 menu system. NOTE To view the MX410/MX412 menu tree, refer to “Menu Trees” on page 5-5. Menu A menu is a display that provides numbered selections that are used to navigate to related menus, modify provisioning information, or display information screens.
PAGE 58
MX410/MX412 System Manual MENU LAYOUT AND NAVIGATION Figure 5-1 illustrates the basic menu layout used in the MX410/MX412 menu system. The MX410/MX412 Menu Layout figure is general in nature, and not all menus contain all of the elements shown in the figure. MX410 Active Alarms: CRITICAL MAJOR MINOR ALERT 2 1 3 ID: 04/10/05 01:25 MX410 Menu Title 1 2 3 4 5 6 4 5 Selection : - Option Option Option Option Option Option : current selection (T)oggle '?' - System Help Screen Figure 5-1.
PAGE 59
Menu Trees Basic menu navigation is accomplished by selecting the desired option number and then pressing ENTER. To return to the previous menu, press the ESC (escape) key. The System Help screen can be accessed from any MX410/MX412 screen or menu by pressing “?”. Table 5-1 shows the general keyboard commands for the MX410/MX412. Table 5-1.
PAGE 60
MX410/MX412 System Manual Unit Name CLEI Code Part Number Serial Number Product Revision MAC Address Code Version Code Checksum Boot Version Boot Checksum 1. Configuration Main Menu 2. Provisioning A 3. Quick Setup B 4. Status 5. Test C 6. Performance Monitoring 1. Daily PM Table 2. Quarter Hour PM Table 3. Daily PM Thresholds 4. Quarter Hour PM Thresholds 5. Clear All PM Data 1. ES-L Threshold 2. CV-P Threshold (ESF mode) 3. CV-P Threshold (SF mode) 4. ES-P Threshold 5. SES-P Threshold 6.
PAGE 61
Menu Trees 1. Line Legnth 1. DS1 Ports 1. DS1 Provisioning - Port #1 2. DS1 Provisioning - Port #2 3. DS1 Provisioning - Port #3 4. DS1 Provisioning - Port #4 1. 0 - 133 ft 2. 133 - 266 ft 3. 266 - 399 ft 4. 399 - 533 ft 5. 533 - 655 ft 6. - 22.5 dB 7. - 15 dB 8. - 7.5 dB 9. - 0 dB (MX412 Only) 12. DS1 Provisioning - Port #12 A 2. Line Coding 1. B8ZS 2. AMI 3. Loopback Detection 1. Enabled 2. Disabled 4. Framing 1. ESF 2. SF 5. SNMP Line Status Trap 1. Enabled 2. Disabled 6.
PAGE 62
MX410/MX412 System Manual A1 1. Choose TO Group 3. Cross-Connect Mapping DS1 1 (DS0 1 - 24) DS1 2 (DS0 1 - 24) DS1 3 (DS0 1 - 24) DS1 4 (DS0 1 - 24) DS1 12 (DS0 1 - 24) 1. DS1 1 2. DS1 2 3. DS1 3 4. DS1 4 12. DS1 12 2. Choose TO DS0 3. Robbed Bit Signaling Enter to DS0 1. Enabled 2. Disabled 4. Apply Cross-Connect 1. Choose FROM PPP 1. PPPs 2. Choose TO Group 3. Choose TO DS0 Range 4. Apply Cross-Connect Ports 1. Choose TO Group 2. V.35 1. PPP 1 2. PPP 2 3. PPP 3 4. PPP 4 1. DS1 1 2. DS1 2 3.
PAGE 63
Menu Trees A2 1. Terminal State 4. Terminal Server 1. Port 1 2. Port 2 3. Port 3 4. Port 4 2. Baud Rate 3. Telnet Port Number 4. Security 5. Username 6. Password 7. Mode 8. Far End IP-Address 1. Craft Port Baud Rate 5. General 2. Date 3. Time 4. System ID 5. Auto-Logoff Inactivity Time 1. Enabled 2. Disabled 1. 9600 2. 19200 3. 38400 4. 57600 5. 115200 New Port Number 1. Enabled 2. Disabled New Username New Password 1. Server 2. Client IP Address 1. 9600 2. 19200 3. 38400 4. 57600 5.
PAGE 64
MX410/MX412 System Manual 1. IP Address A3 1. Ethernet 1. IP Address Subnet Mask 2. Subnet Mask 3. Apply Settings 2. Gateway MAC Address Eth (1 - 4) 3. Link Speed & Duplex Functional Link Speed & Duplex Link Status 6. Network Management 1. BCP/IPCP 2. PPP BCP/IPCP PPP (1 - 4) 2. IP Address Subnet Mask Far End IP Address 3. SNMP Link Status Trap 4. PPP MTU LCP Status BCP/IPCP Status 3. DHCP 1. State 2. Network 3. Default Router 4. DNS Router 5. Address Range 6.
PAGE 65
Menu Trees A4 7. SNMP 1. SNMP State 2. Trap Host 1 IP 3. Trap Host 2 IP 4. Trap Host 3 IP 5. Trap Host 4 IP 6. SNMP Traps 7. System Name 8. System Location 9. System Contact 10. Read Community 11. Write Community 8. System Configuration Archive (SCA) 1. SCA TFTP Server 2. Remote Filename 3. All/Data Path Only 9. Save Provisioning 10. Auto Save 4. Perform SCA Save 5. Perform SCA Restore 6. Auto Save Time 7. Auto Save 1. Enabled 2. Disabled 1. Trap Host IP 2. Trap Host Method 3. Trap Host Status 1.
PAGE 66
MX410/MX412 System Manual 1. Choose FROM PPP 1. PPPs 2. Choose TO Group B 3. Choose TO DS0 Range 4. Apply Cross-Connect 1. Choose TO Group 2. V.35 1. PPP 1 2. PPP 2 3. PPP 3 4. PPP 4 1. DS1 1 2. DS1 2 3. DS1 3 4. DS1 4 Enter TO DS0 Range 1. DS1 1 2. DS1 2 3. DS1 3 4. DS1 4 (MX412 Only) 12. DS1 12 2. Choose TO DS0 Range 3. Apply Cross-Connect 1. Choose TO Group Enter TO DS0 Range 1. DS1 1 2. DS1 2 3. DS1 3 4. DS1 4 3. FXS (MX412 Only) 12. DS1 12 2. Choose TO DS0 3. Mode 4.
PAGE 67
Menu Trees 1. Choose TO Group B1 8. Cross-Connect Setup DS1 1 (DS0 1 - 24) DS1 2 (DS0 1 - 24) DS1 3 (DS0 1 - 24) DS1 4 (DS0 1 - 24) (MX412 Only) 12. DS1 12 2. Choose TO DS0 (MX412 Only) DS1 12 (DS0 1 - 24) 1. DS1 1 2. DS1 2 3. DS1 3 4. DS1 4 3. Robbed Bit Signaling Enter to DS0 1. Enabled 2. Disabled 4. Apply Cross-Connect 1. Choose FROM PPP 1. PPPs 2. Choose TO Group Ports 3. Choose TO DS0 Range 4. Apply Cross-Connect 1. Choose TO Group 2. V.35 1. PPP 1 2. PPP 2 3. PPP 3 4. PPP 4 1. DS1 1 2.
PAGE 68
MX410/MX412 System Manual C DS1 Ports 1. #1 2. #2 3. #3 4. #4 5. #5 6. #6 7. #7 8. #8 9. #9 10. #10 11. #11 12. #12 1. Loopback Pattern DS1 x Status 1. Data Mode 2. Payload 3. Line 4. Inward 5. Dual 6. Remote FDL Line 7. Remote Inband Line (CSU) 8. Remote FDL Payload 9. Pattern Test Execute (Y, N) 1. QRSS 2. All Ones 3. All Zeros 4. 511 5. 2047 6. 2^15-1 7. 2^20-1 Execute (Y, N) 13. Reset ALL Tests 14. Loopback Timeout 1. 120 Minutes 2. 90 Minutes 3. 60 Minutes 4. 30 Minutes 5. 15 Minutes 6.
PAGE 69
Menu Descriptions MENU DESCRIPTIONS The MX410/MX412 Main Menu (see Figure 5-11) is the access point to all other operations. Each Main Menu item has several functions and submenus that identify and provide access to specific operations and parameters.
PAGE 70
MX410/MX412 System Manual Configuration Screen The Configuration Screen (see Figure 5-12) displays information about the MX410/MX412. Some information is updated automatically, such as Code Version changes as upgrades are performed. The CLEI Code and Part Number can be used to search for related information on the ADTRAN website or to order additional parts. Some information from this menu may be required when calling ADTRAN Technical Support.
PAGE 71
Menu Descriptions Table 5-3. MX410/MX412 Configuration Screen Fields (Continued) Field Description Code Checksum This field displays the checksum of the current firmware revision level of the MX410/MX412. Boot Version This field displays the Boot ROM software revision code of the MX410/MX412. Boot Checksum This field displays the checksum of the Boot ROM software revision code of the MX410/MX412.
PAGE 72
MX410/MX412 System Manual Provisioning Menu The Provisioning Menu (see Figure 5-13) is used to configure and change the operating characteristics of the MX410/MX412. Some options control traffic through the MX410/ MX412 by affecting the DS1, V.35, terminal server ports and cross-connect mapping while other options affect overall operation, Network Management, SNMP and System Configuration Archive (SCM) of the MX410/MX412.
PAGE 73
Menu Descriptions Table 5-4. Provisioning Menu Options (Continued) Option Description Function 8 System Configuration Archive (SCA) This option displays the “SCA Update Menu” on page 5-51. 9 Save Provisioning This option is used to save current network settings. Auto Save This option is used to automatically save current network settings at timed intervals.
PAGE 74
MX410/MX412 System Manual DS1 Ports Menu The DS1 Ports menu (see Figure 5-14) displays line length, line coding, loopback detection, framing, SNMP line status trap, SNMP link status trap, circuit ID, interface state, and alarm pass thru information for DS1 ports 1-4 (1-12 on the MX412), as well as timing information. Selection of an option invokes other menus to set the option variables. The Toggle hot key can be used to view more DS1 port information shown in Figure 5-15.
PAGE 75
Menu Descriptions The DS1 Ports menu options are listed in Table 5-5. Table 5-5. DS1 Ports Menu Options Option Description Function 1 DS1 Port #1 This option displays the “DS1 Provisioning Menu” on page 5-22. 2 DS1 Port #2 This option displays the “DS1 Provisioning Menu” on page 5-22. 3 DS1 Port #3 This option displays the “DS1 Provisioning Menu” on page 5-22. 4 DS1 Port #4 This option displays the “DS1 Provisioning Menu” on page 5-22.
PAGE 76
MX410/MX412 System Manual DS1 Provisioning Menu The DS1 Provisioning menu (see Figure 5-16) is used to set the line length, line coding, loopback detection, framing, SNMP line status trap, SNMP link status trap, circuit ID, interface state, and alarm pass thru information for the selected DS1 port.
PAGE 77
Menu Descriptions Table 5-6. DS1 Provisioning Menu Options (Continued) Option Description Function 2 Line Coding This option sets the line code for each individual port interface to match the connected device. Options for line coding are as follows: • AMI • B8ZS 3 Loopback Detection This option enables or disables a port to respond to CSU and FDL loopback requests coming from the network. 4 Framing This option sets the framing.
PAGE 78
MX410/MX412 System Manual Primary Timing Mode Menu The Primary Timing Mode menu (see Figure 5-17) is used to set the primary timing mode for the selected DS1 port (1-4 on the MX410 and 1-12 on the MX412). MX410 Active Alarms: CRITICAL MAJOR ID: MM/DD/YY HH:MM MX410 Primary Timing Mode : DS1 1 1 2 3 4 5 - Internal DS1 1 DS1 2 DS1 3 DS1 4 Selection : '?' - System Help Screen Figure 5-17. Primary Timing Mode Menu The Primary Timing Mode menu options are listed in Table 5-7. Table 5-7.
PAGE 79
Menu Descriptions Secondary Timing Mode Menu The Secondary Timing Mode menu (see Figure 5-18) is used to set the secondary timing mode for the selected DS1 port (1-4 on the MX410 and 1-12 on the MX412). MX410 Active Alarms: CRITICAL MAJOR ID: MM/DD/YY HH:MM MX410 Secondary Timing Mode : DS1 3 1 2 3 4 5 - Internal DS1 1 DS1 2 DS1 3 DS1 4 Selection : '?' - System Help Screen Figure 5-18. Secondary Timing Mode Menu The Secondary Timing Mode menu options are listed in Table 5-8. Table 5-8.
PAGE 80
MX410/MX412 System Manual V.35 Port Menu The V.35 Port menu (see Figure 5-19) is used to provision the V.35 Port. MX410 Active Alarms: CRITICAL ID: MM/DD/YY HH:MM MX410 V.35 Port 1 - CTS 2 - DCD 3 - DSR : Forced On : Forced On : Normal Selection : '?' - System Help Screen Figure 5-19. V.35 Port Menu The V.35 Port menu options are listed in Table 5-9. Table 5-9. V.35 Port Menu Options Option Description Function 1 CTS This option sets the CTS (Clear To Send) settings.
PAGE 81
Menu Descriptions Cross-Connect Mapping Menu The Cross-Connect Mapping menu is used to display DS0 information for the four DS1 ports (12 ports on the MX412), as well as FXS (MX412 only), PPP, and V.35 settings. The CrossConnect Mapping menu is shown in Figure 5-20 displaying DS0 mapping for the DS1 1 port. The Toggle hot key is used to view DS1 2, DS1 3, DS1 4, PPP, and V.35 data. All of the DS1 toggle menus have identical options, and all of the 24 DS0s have identical options for the selected DS1.
PAGE 82
MX410/MX412 System Manual The Cross-Connect Mapping menu options are listed in Table 5-10. Table 5-10. Cross-Connect Mapping Menu Options Option 1-24 Description Function DS0 1-24 connections These options invoke the Change Cross-Connect Mapping menu which is used to provision the cross-connect settings for the selected DS1 port.
PAGE 83
Menu Descriptions Table 5-10. Cross-Connect Mapping Menu Options (Continued) Option Description Function 4 Frame Relay This option invokes the Change Cross-Connect Mapping menu, which is used to provision the frame relay ports.
PAGE 84
MX410/MX412 System Manual Terminal Server Ports Menu The Terminal Server Ports menu (see Figure 5-22) is used to select Terminal Port 1 through Port 4 for provisioning. MX410 Active Alarms: CRITICAL ID: MM/DD/YY HH:MM MX410 Terminal Server Ports 1 2 3 4 Selection : - Port Port Port Port 1 2 3 4 '?' - System Help Screen Figure 5-22. Terminal Server Ports Menu The Terminal Server Ports menu options are listed in Table 5-11. Table 5-11.
PAGE 85
Menu Descriptions Terminal Server Port (1 - 4) Menu The Terminal Server Port menu (see Figure 5-23) is used to provision the Terminal Sever Port selected on the (previous) Terminal Server Ports menu.
PAGE 86
MX410/MX412 System Manual Table 5-12. Terminal Server Port Menu Options (Continued) Option Description Function 6 Password This option is used to assign a password to the selected port number for use when security is enabled. 7 Mode This option sets Telnet request mode. Options are as follows: • Server (listen for Telnet Requests) • Client (issue Telnet Requests) 8 5-32 Far End IP-Address This option is used to enter the far end IP address.
PAGE 87
Menu Descriptions General Provisioning Menu The General Provisioning menu (see Figure 5-24) is used to provision the craft port Baud rate, the date, time, system ID, auto-logoff inactivity time, to reset the MX410/MX412, and to handle security administration.
PAGE 88
MX410/MX412 System Manual Table 5-13. General Provisioning Menu Options (Continued) Option 5 Description Function Auto-Logoff Inactivity Time This option defines when a menu session automatically terminates due to inactivity. The default setting is 15 Minutes. Options are as follows: • 120 Minutes • 90 Minutes • 60 Minutes • 30 Minutes • 15 Minutes • 10 Minutes • 5 Minutes • Disabled 6 Card Reset This option forces the MX410/MX412 to reset.
PAGE 89
Menu Descriptions Network Management Menu The Network Management menu (see Figure 5-25) is used to provision network information. MX410 Active Alarms: CRITICAL MAJOR ID: MM/DD/YY HH:MM MX410 Network Management 1 2 3 4 5 - Ethernet PPP BCP/IPCP DHCP Frame Relay Interface Network Mode Selection : '?' - System Help Screen Figure 5-25. Network Management Menu The Network Management menu options are listed in Table 5-14. Table 5-14.
PAGE 90
MX410/MX412 System Manual Ethernet Menu The Ethernet menu (see Figure 5-26) is used to provision Ethernet information. MX410 Active Alarms: CRITICAL ID: MM/DD/YY HH:MM MX410 Ethernet 1 - IP Address Subnet Mask 2 - Gateway MAC Address : : : : 192.168.100.1 255.255.0.0 192.168.1.1 XX:XX:XX:XX:XX:XX Eth 1 3 - Link Speed & Duplex : Auto Functional Link Speed & Duplex : Unknown Link Status : Down (T)oggle Between Interfaces Selection : '?' - System Help Screen Figure 5-26.
PAGE 91
Menu Descriptions Table 5-15. Ethernet Menu Options (Continued) Option N/A Description Function MAC Address This read-only field displays the Medium Access Control (MAC) Address. MAC Addresses are location-independent (programmed into the card at manufacture, they relocate when the card does). MAC Addresses are contained in the headers of packets and are used to filter and forward packets.
PAGE 92
MX410/MX412 System Manual PPP BCP/IPCP Menu Point-to-Point Protocol (PPP) is commonly used for LAN extension and Remote management connectivity. PPP can use one of two upper layer protocols: • BCP (Bridge Control Protocol): This protocol routes packets based on MAC addresses and allows broadcast traffic to be passed over the PPP link(s). This protocol enables true LAN Extension to be completed. Any device on the LAN can communicate with any other device with the least amount of configuration by the user.
PAGE 93
Menu Descriptions The PPP BCP/IPCP menu options are listed in Table 5-16. Table 5-16. PPP BCP/IPCP Menu Options Option Description Function 1 BCP/IPCP This option is used to select either BCP (Bridge Control Protocol) or IPCP (IP Control Protocol for routing). This option also changes the Routing Mode between disabled and enabled respectively. PPP (1-4) 2 IP Address This option invokes another menu which is used to enter the IP Address, the Subnet Mask for the PPP.
PAGE 94
MX410/MX412 System Manual DHCP Server Menu The DHCP (Dynamic Host Configuration Protocol) Server menu, shown in Figure 5-28, is used to provision DHCP server connections. MX410 Active Alarms: CRITICAL MAJOR ID: MM/DD/YY HH:MM MX410 DHCP Server 1 2 3 4 5 6 - State Network Default Router DNS Router Address Range Lease Time (d:h:m) : : : : : : Disabled Not Set/Not Set Not Set Not Set 0.0.0.0-255.255.255.255 0:0:0 Selection : '?' - System Help Screen Figure 5-28.
PAGE 95
Menu Descriptions Frame Relay Menu The Frame Relay menu, shown in Figure 5-29, is used to provision the frame relay. Use T to toggle through the frame relays 1–4. MX410 Active Alarms: CRITICAL MAJOR ID: MM/DD/YY HH:MM MX410 Frame Relay 1 : Down 1 2 3 4 - Type View VC Create New VC Delete VC : User (T)oggle Between Interfaces Selection : '?' - System Help Screen Figure 5-29. Frame Relay Menu The Frame Relay menu options are listed in Table 5-18. Table 5-18.
PAGE 96
MX410/MX412 System Manual Frame Relay Type Menu The Frame Relay Type menu, shown in Figure 5-30, is used to select the frame relay type. MX410 Active Alarms: CRITICAL MAJOR ID: MM/DD/YY HH:MM MX410 Frame Relay 1 Type : User 1 2 3 4 - Selection : None Network (DCE) User (DTE) Both (NNI) '?' - System Help Screen Figure 5-30. Frame Relay Type Menu The Frame Relay Type menu options are listed in Table 5-20. Table 5-20.
PAGE 97
Menu Descriptions View Frame Relay Menu The View Frame Relay menu, shown in Figure 5-31, is used to select a VC for viewing and provisioning. MX410 Active Alarms: CRITICAL MAJOR ID: MM/DD/YY HH:MM MX410 View Frame Relay 1 VC 1 2 3 4 - Selection : VC VC VC VC 1 2 3 4 '?' - System Help Screen Figure 5-31. View Frame Relay Menu The View Frame Relay menu options are listed in Table 5-21. Table 5-21.
PAGE 98
MX410/MX412 System Manual Frame Relay Port Menu The Frame Relay Port menu, shown in Figure 5-32, is used to provision the selected VC. MX410 Active Alarms: CRITICAL MAJOR ID: MM/DD/YY HH:MM MX410 Frame Relay Port 1 VC 1 : Active 1 - Frame Relay DLCI 2 - IP Address Subnet Mask 3 - Frame Relay MTU : : : : Selection : 16 10.10.10.1 255.255.255.0 1500 '?' - System Help Screen Figure 5-32. Frame Relay Port Menu The Frame Relay Port menu options are listed in Table 5-22. Table 5-22.
PAGE 99
Menu Descriptions Network Mode Menu The Network Mode menu, shown in Figure 5-33, is used to provision the network mode. NOTE Changing the IP routing mode changes the BCP/IPCP setting for the PPP links. MX410 Active Alarms: CRITICAL MAJOR ID: MM/DD/YY HH:MM MX410 Network Mode 1 - IP Routing 2 - RIP 3 - OSPF : Disabled : Disabled : Disabled Selection : '?' - System Help Screen Figure 5-33. Network Mode Menu The Network Mode menu options are listed in Table 5-23. Table 5-23.
PAGE 100
MX410/MX412 System Manual RIP Provisioning Menu The RIP Provisioning menu, shown in Figure 5-34, is used to provision the RIP routing protocol and the RIP version. MX410 Active Alarms: CRITICAL MAJOR ID: MM/DD/YY HH:MM MX410 RIP Provisioning 1 - State 2 - Version Selection : : Enabled : Version 2 '?' - System Help Screen Figure 5-34. RIP Provisioning Menu The RIP Provisioning menu options are listed in Table 5-24. Table 5-24.
PAGE 101
Menu Descriptions OSPF Provisioning Menu The OSPF Provisioning menu, shown in Figure 5-35, is used to provision the OSPF. MX410 Active Alarms: CRITICAL MAJOR ID: MM/DD/YY HH:MM MX410 OSPF Provisioning 1 - State 2 - Network Address Wildcard Area Selection : : : : : Enabled 0.0.0.0 255.255.255.255 0 '?' - System Help Screen Figure 5-35. OSPF Provisioning Menu The OSPF Provisioning menu options are listed in Table 5-25. Table 5-25.
PAGE 102
MX410/MX412 System Manual OSPF Network Menu The OSPF Network menu, shown in Figure 5-36, is used to set the network address, wildcard, and area. MX410 Active Alarms: CRITICAL MAJOR ID: MM/DD/YY HH:MM MX410 OSPF Network 1 2 3 4 - Address Wildcard Area Apply Settings : 0.0.0.0 : 255.255.255.255 : 0.0.0.0 Selection : '?' - System Help Screen Figure 5-36. OSPF Network Menu The OSPF Network menu options are listed in Table 5-26. Table 5-26.
PAGE 103
Menu Descriptions SNMP Menu The SNMP (Simple Network Management Protocol) menu (see Figure 5-37) is used to provision SNMP information. MX410 Active Alarms: CRITICAL MAJOR MINOR ID: MM/DD/YY HH:MM MX410 SNMP 1 2 3 4 5 6 7 8 9 10 11 - SNMP State Trap Host 1 IP Trap Host 2 IP Trap Host 3 IP Trap Host 4 IP SNMP Traps System Name System Location System Contact Read Community Write Community : : : : : : : : : : : Disabled 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.
PAGE 104
MX410/MX412 System Manual Table 5-27. SNMP Menu Options (Continued) Option Description Function 5 Trap Host 4 IP This option invokes another menu which is used to enter the Trap Host 4 IP address of an SNMP manager to which the MX410/MX412 sends traps, the method (version 1 traps or version 2 notifications), and enable or disable the trap host.
PAGE 105
Menu Descriptions SCA Update Menu The SCA (System Configuration Archive) Update menu (see Figure 5-38) is used to update SCA information. MX410 Active Alarms: CRITICAL MAJOR ID: MM/DD/YY HH:MM MX410 SCA Update 1 2 3 4 5 - SCA TFTP Server : 0.0.0.0 Remote Filename : All/Data Path Only : All Provisioning Perform SCA Save Perform SCA Restore 6 - Auto Save Time 7 - Auto Save : Wed 10:35 : Disabled Awaiting download. Selection : '?' - System Help Screen Figure 5-38.
PAGE 106
MX410/MX412 System Manual Quick Setup Menu The Quick Setup menu (see Figure 5-39) is used to simplify the installation process. All of the basic configuration options necessary to setup the MX410/MX412 are grouped together. The Quick Setup menu allows configuration of such items as DS0 drop assignments, as well as system date, time, and IP Address information. MX410 Unacknowledged Alarms: CRITICAL ID: MM/DD/YY HH:MM MX410 Quick Setup Ports 1 - PPPs PPP 1 2 - V.
PAGE 107
Menu Descriptions Table 5-29. Quick Setup Menu Options (Continued) Option 3 Description Function FXS (MX412 only) This option is used to provision the FXS port. Options are as follows: • Choose TO Group (for DS1 1 through DS1 4) • Choose TO DS0 Range: enter a range • Mode: Select Loop Start, PLAR D4, PLAR D3, or FX Ringdown. Refer to Table 4-6 on page 4-9 for descriptions of these options. • Apply Cross-Connect 3 System ID This option is used to assign a new system ID.
PAGE 108
MX410/MX412 System Manual Status Screens The Status screens (see Figure 5-40, Figure 5-41, and Figure 5-42) provides detailed status information about the DS1 Ports, Ethernet Ports, PPP, Timing, Power Feed, and Frame Relay. Use the T to toggle through the screens. The MX410 has two status screens and the MX412 has three.
PAGE 109
Menu Descriptions MX412 Active Alarms: CRITICAL MAJOR ID: MM/DD/YY HH:MM MX412 Status Frame Relay Port 1 : Enabled : Up VC 1 - Active DLCI VC 2 - Inactive DLCI VC 3 - Inactive DLCI VC 4 - Inactive DLCI Port VC VC VC VC 2 1 2 3 4 : - Disabled Inactive Inactive Inactive Inactive = = = = 16 17 18 19 Port VC VC VC VC 3 1 2 3 4 : - Disabled Inactive Inactive Inactive Inactive : Down DLCI = DLCI = DLCI = DLCI = 16 17 18 19 : Down DLCI = DLCI = DLCI = DLCI = 16 17 18 19 Port VC VC VC VC 4 1 2 3
PAGE 110
MX410/MX412 System Manual Table 5-30. Status Screen Fields (Continued) Option Description Function PPP Interfaces 1-4 State This field displays the current state of the four PPP interfaces as either Enabled or Disabled. N/A LCP This field displays the active state of this control protocol as either Up or Down. N/A BCP This field Displays the active state of this control protocol as either Up or Down. N/A IPCP This field Displays the active state of this control protocol as either Up or Down.
PAGE 111
Menu Descriptions Table 5-30. Status Screen Fields (Continued) Option Description Function Port 1–4 State This field displays the state as either enabled or disabled. Port 1–4 Status This field displays the port status as either up or down. VC 1–4 Status This field displays the VC status as one of the following states: Frame Relay • Inactive - VC is not communicating with the port. • Active - VC is communicating with the port.
PAGE 112
MX410/MX412 System Manual Test Menu The Test menu (see Figure 5-43) provides options for testing the DS1 Ports. MX410 Active Alarms: CRITICAL MAJOR ID: MM/DD/YY HH:MM MX410 Test DS1 Ports 1 2 3 4 - #1 #2 #3 #4 : : : : Pattern Data mode Data mode Data mode 5 - Reset ALL Tests 6 - Loopback Timeout: Selection : 120 Minutes '?' - System Help Screen Figure 5-43. Test Menu The Test menu options are listed in Table 5-31. Table 5-31.
PAGE 113
Menu Descriptions DS1 (Port #) Menu The DS1 (Port #) menu (see Figure 5-44) provides options for testing the DS1 Ports. MX410 Active Alarms: CRITICAL MAJOR ID: MM/DD/YY HH:MM MX410 DS1 1 1 - Loopback : Pattern Pattern : Ones 2 - Insert One Bit Error 3 - Clear Bit Error Count Patt Sync : NO SYNC Bit Errors : 14 DS1 1 Status Selection: : LOS,TX RAI '?' - System Help Screen Figure 5-44. DS1 (Port #) Menu The DS1 (Port #) menu options are listed in Table 5-32. Table 5-32.
PAGE 114
MX410/MX412 System Manual Port (#) Test Menu The Port (#) Test menu (see Figure 5-45) provides options for testing the DS1 Ports. MX410 Active Alarms: CRITICAL MAJOR ID: MM/DD/YY HH:MM MX410 Port #1 : Pattern 1 2 3 4 5 6 7 8 9 - Selection: Data Mode Payload Line Inward Dual Remote FDL Line Remote Inband Line (CSU) Remote FDL Payload Pattern Test '?' - System Help Screen Figure 5-45. Port (#) Test Menu The Port (#1-#4 on MX410, and #1-#12 on MX412) Test menu options are listed in Table 5-33.
PAGE 115
Menu Descriptions DS1 Test Pattern Menu The DS1 Test Pattern menu (see Figure 5-46) provides options for testing the DS1 ports using pattern data. MX410 Active Alarms: CRITICAL MAJOR ID: MM/DD/YY HH:MM MX410 DS1 1 Test Pattern 1 2 3 4 5 6 7 Selection : - QRSS All Ones All Zeros 511 2047 2^15-1 2^20-1 '?' - System Help Screen Figure 5-46. DS1 Test Pattern Menu The DS1 Test Pattern menu options are all test pattern types.
PAGE 116
MX410/MX412 System Manual Performance Monitoring Menu The Performance Monitoring menu (see Figure 5-47) provides options for viewing performance data affecting the MX410/MX412 operations. Data is viewed in daily or 15-minute increments.
PAGE 117
Menu Descriptions Table 5-35. Performance Monitoring Definitions T1 PM Parameter Definition Description CV-L Code Violation - Line This parameter indicates the number of Bipolar Violations (BPVs) and Excessive Zeros (EXZs) that have occurred during the accumulation period. ES-L Errored Seconds - Line This parameter indicates the number of seconds for which one or more Line Coding Violations (CV-Ls), or one or more Loss of Signal (LOS) defects occurred.
PAGE 118
MX410/MX412 System Manual The hot keys used in the Performance Monitoring submenus are listed in Table 5-36. Table 5-36. Performance Monitoring Menu Hot Keys Hot Key or Terminology Description * = Invalid Interval An asterisk indicates that the interval is off by plus or minus ten seconds. (N)ext DS1 This hot key displays the performance monitoring statistics for the next DS1 port. (P)revious DS1 This hot key displays the performance monitoring statistics for the previous DS1 port.
PAGE 119
Menu Descriptions Daily Performance Monitoring Screen The Daily Performance Monitoring screen (see Figure 5-48) displays DS1 performance monitoring data in daily increments and in a tabular format.
PAGE 120
MX410/MX412 System Manual Daily PM Thresholds Menu The Daily PM Thresholds menu (see Figure 5-50) displays DS1 performance monitoring thresholds data in a tabular format. This menu is used to set the performance monitoring threshold levels and enable or disable an alarm if the threshold is exceeded.
PAGE 121
Menu Descriptions Table 5-37. Daily PM Thresholds Menu Options (Continued) Option Description Function 8 UAS-P This option sets the UAS-P threshold value. The available threshold range is (1-65535). The default value is 10. 9 Restore ALL DS1 Threshold Defaults This option restores all threshold values to the defaults listed above. 10 Enable ALL DS1 Threshold Alarms This option enables all daily threshold alarms.
PAGE 122
MX410/MX412 System Manual Quarter Hour PM Thresholds Menu The Quarter Hour PM Thresholds menu (see Figure 5-51) displays DS1 performance monitoring thresholds data in a tabular format. This menu is used to set the performance monitoring threshold levels and enable or disable alarms if the thresholds are exceeded.
PAGE 123
Menu Descriptions Table 5-38. Quarter Hour PM Thresholds Menu Options (Continued) Option Description Function 8 UAS-P This option sets the UAS-P threshold value. The available threshold range is (1-900). The default value is 10. 9 Restore ALL DS1 Threshold Defaults This option restores all threshold values to the defaults listed above. 10 Enable ALL DS1 Threshold Alarms This option enables all quarter hour threshold alarms.
PAGE 124
MX410/MX412 System Manual Upload PM Flat File Menu The Upload PM Flat File menu (see Figure 5-52) provides options for uploading the performance monitoring flat file. NOTE The comma delimited format of the flat file allows for the PM data to be imported into a spreadsheet for analysis or graphical depiction (see Table 5-40 and Figure 5-53). MX410 Active Alarms: CRITICAL MAJOR ID: MM/DD/YY HH:MM MX410 Upload PM Flat File 1 - SCA TFTP Server 2 - Remote Filename : 0.0.0.
PAGE 125
61189500L1-1F Table 5-40. Example Data from PM Flat File 15-MIN CV-L Ifld Timestamp ES-L SES-L LOSS-L CV-P ES-P SES-P SAS-P UAS-P CSS-P MIN LVL (dB) MAX LVL (dB) interval 1 01/16 12:30 1 0 0 0 0 0 2 0 0 0 2 -12 -7 1 01/16 12:15 2 0 0 0 0 0 1 0 0 0 1 -12 -12 1 01/16 12:00 3 2 1 0 0 0 3 1 1 0 2 -12 0 1 01/16 11:45 4 0 0 0 0 0 1 0 0 0 1 0 0 1 01/16 11:30 5 0 0 0 0 0 1 0 0 0 1 -6 0 . . . . . . . . .
PAGE 126
15-MIN CV-L Ifld Timestamp 12 SES-L LOSS-L CV-P ES-P SES-P SAS-P UAS-P CSS-P interval 2 . . . ES-L 672 . . . . . . 0 0 0 0 0 0 0 0 0 0 MIN LVL (dB) MAX LVL (dB) MX410/MX412 System Manual 5-72 Table 5-40.
PAGE 127
Menu Descriptions Errored Seconds Graph for IFID 1 # of Errored Seconds 539 87 19 1 2 3 4 5 21 Intervals 22 672 Figure 5-53.
PAGE 128
MX410/MX412 System Manual System Alarms Menu The System Alarms menu (see Figure 5-54) provides options for viewing all alarms affecting MX410/MX412 system operations. Alarms may be viewed within the Master Log menu (detailed in the next section). The Environmental Alarms menu contains provisionable options. The Alarm Chronology menu offers the viewing of alarms in either ascending or descending order.
PAGE 129
Menu Descriptions Master Log Menu The Master Log menu (see Figure 5-55) is used to review and acknowledge alarms.
PAGE 130
MX410/MX412 System Manual Table 5-41. Master Log Menu Terminology and Hot Keys (Continued) Hot Key or Terminology Description (L)ast This hot key indicates that pressing the L key displays the last alarms in the current chronological sequence. (C)lear This hot key indicates that pressing the C key clears all inactive alarms. (A)cknowledge This hot key indicates that pressing the A key acknowledges all unacknowledged alarms (which removes asterisks from the menu).
PAGE 131
Menu Descriptions Code Download Method Menu The Code Download Method menu (see Figure 5-56) provides options for upgrading the software of the MX410/MX412. MX410 Active Alarms: CRITICAL ID: MM/DD/YY HH:MM MX410 Code Download Method 1 - X-MODEM 2 - TFTP Selection : '?' - System Help Screen Figure 5-56. Code Download Method Menu The Code Download Method menu options are listed in Table 5-42. Table 5-42.
PAGE 132
MX410/MX412 System Manual This page is intentionally blank.
PAGE 133
Appendix A Warranty WARRANTY AND CUSTOMER SERVICE ADTRAN will replace or repair this product within the warranty period if it does not meet its published specifications or fails while in service. Warranty information can be found at www.adtran.com/warranty. Refer to the following subsections for sales, support, Customer and Product Service (CAPS) requests, or further information.
PAGE 134
® Carrier Networks Division 901 Explorer Blvd.