Troubleshooting guide
Section 5, User Interface Guide - UIG-500, MX2820 Menu Tree
61186003L1-1D 5-13
SCU MENU TREE
Figure 5-2 shows the menu tree for the MX2820 System Controller Unit (SCU).
Figure 5-2. MX2820 SCU Menu Tree
1. Configuration
Unit Name
CLEI Code
Part Number
Serial Number
Product Revision
Software Revision
Boot ROM Version
MAC Address
2. Provisioning
4. Test
* = Default Settings
2. Self Test and Restart
1. Test Alarm Relays
3. Status
1. General
2. Date
3. Time
4. Auto-Logoff
1. Management Ports
6. Security Administration
7. Change [Currently Logged on]
Password
5. Restore Default Provisioning
1. Password
2. Account Properties/
Access Privilege
2. Subnet Mask (255.255.255.0*)
3. Gateway (0.0.0.0*)
4. Interface
Ethernet Data Rate
1. IP Address (0.0.0.0*)
MAC Address
Ethernet Link
2. Fixed (slot-based)*
1. Sequential (RFC 2863)
2. DISABLE
1. ENABLE*
2. Expansion Shelf
1. Intelligent NE*
2. DISABLE
1. ENABLE*
1. TL1 Telnet Port (2000*)
2. TL1 Raw-ICP Port (2001*)
5. Secondary SSH Port
1. Craft Port Baud Rate
2. Interbank Comm. Mode
HOST
CLIENT*
2. Trap Host 2 IP (0.0.0.0*)
3. Trap Host 3 IP (0.0.0.0*)
4. Trap Host 4 IP (0.0.0.0*)
6. SCU Traps
7. System Name (SysName not set*)
8. System Location (SysLocation not set*)
9. System Contact (www.adtran.com*)
10. Read Community (public*)
11. Write Community (private*)
1. Trap Host 1 IP (0.0.0.0*)
5. ifIndex Method
2. System Name
3. TL1 Telnet Port
4. TL1-Raw-ICP Port
1. Client Shelf Management
2. Copy Module Provisioning
3. Back-up SCU Provisioning to Linecards
4. Back-up Linecard Provisioning to SCU
1. Smart Start
1. Change SCU EQPT Provisioned Service State to OOS/IS
5.Exchange TL1 Ports
2. Network Management
3. SNMP
4. TL1
5. Smart Start
7. Service States
1. Ethernet Interface
3. IP Forwarding
4. FirmwareTFTP Server (0.0.0.0*)
2. Network Service Ports
2. Edit User Accounts
3. Create New User Account
1. Users Currently Logged On
5. Restore Back to Default Accounts
4. Security Options
6. Access Tech Support Account
2. Enable/Disable User Account
3. Delete User
1. Change Password/Access Privilege
1. Enable SNMP Security Account Access (No*)
2. Lock-Out User on Login Failure (No*)
4. Null Password Accepted (No*)
5. Number of Login Failure Before Lock-Out (5*)
3. Case Sensitive Password/User ID (Yes*)
6. Lock-Out Duration in Seconds (60*)
1. 9600*
2. 19200
3. 38400
4. 57600
5. 115200
8. Reboot SCU
DISABLE
ENABLE*
1. ENABLE*
2. DISABLE
Auto-Logoff
Auto-Logoff Time (30 min.*)
SCU EQPT Functional Service State:
SCU EQPT Provisioned Service State:
Shelf: 1 ADTRAN MX2820 System 04/15/04 16:28
Unacknowledged Alarms: CRITICAL MAJOR TID: SysName not set
Status
Hardware LEDs
Ethernet Link : Up ACT : Grn/Ylw
ALM : Red
Alarm Relays
Critical Inactive
Major Active
Minor Inactive
External Inputs Status Level
Ext ACO Inactive N/A
AUX #1 INPUT Inactive MAJOR
AUX #2 INPUT Inactive MAJOR
AUX #3A INPUT Inactive MAJOR
AUX #3B INPUT Inactive MAJOR
PWR Bus A Active MAJOR
PWR Bus B Inactive MAJOR
'?' - System Help Screen
6. IP Services Port Access Control
6. System Configuration Archive (SCA)
2. SCA Restore Provisioning Options
3. SCA Operations
1. SCA Autosave Provisioning
1. Autosave System
2. Autosave Only If Prov Changes
3. Autosave Filename Prefix
4. Autosave Filename Suffix
5. Max Autosave File Instances
6. Autosave Time
7. Autosave Retries
2. DISABLE*
1. ENABLE
2. DISABLE
1. ENABLE*
1. Restore Provisions To SCU
2. Restore Provisions To Modules
2. DISABLE*
1. ENABLE
2. DISABLE
1. ENABLE*
1. SCA TFTP Server
2. SCA Remote Filename
3. SCA Autosave status
4. Perform TFTP SCA Save
5. Perform TFTP SCA Restore
6. TFTP SCA Save Status
7. TFTP SCA Restore Status
8. SSH Configuration
1. Auto*
2. 10 Mbps
3. 100 Mbps
7. RADIUS
3. Secondary Telnet Port
(1024-65535) (2002*)
4. TL1 SSH Port
5. SCA TFTP Server (0.0.0.0*)