NetVanta 6355 PoE Hardware Installation Guide 1200740E1 NetVanta 6355 PoE 1200690E1 NetVanta Quad FXS Voice Interface Module 1202691G1 NetVanta Quad FXO Voice Interface Module 1202692E1 NetVanta Dual FXS/FXO Voice Interface Module 1200695L1 NetVanta T1/PRI Voice Interface Module 1200696G1 NetVanta E1/PRI Voice Interface Module 1202862L1 NetVanta T1/FT1 Network Interface Module 1202863L1 NetVanta T1/FT1 + DSX-1 Network Interface Module 1202872L1 NetVanta Dual T1 Network Interface Module 120
Trademarks NetVanta 6355 PoE Hardware Installation Guide Trademarks Any brand names and product names included in this manual are trademarks, registered trademarks, or trade names of their respective holders. To the Holder of the Manual The contents of this manual are current as of the date of publication. ADTRAN reserves the right to change the contents without prior notice.
NetVanta 6355 PoE Hardware Installation Guide Conventions Conventions Notes provide additional useful information. Cautions signify information that could prevent service interruption or damage to the equipment. Warnings provide information that could prevent injury or endangerment to human life. 61200740E1-34E Copyright © 2011 ADTRAN, Inc.
Safety Instructions NetVanta 6355 PoE Hardware Installation Guide Safety Instructions When using your telephone equipment, please follow these basic safety precautions to reduce the risk of fire, electrical shock, or personal injury: 1. Do not use this product near water, such as a bathtub, wash bowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool. 2. Avoid using a telephone (other than a cordless type) during an electrical storm. There is a remote risk of shock from lightning. 3.
NetVanta 6355 PoE Hardware Installation Guide FCC-Required Information FCC-Required Information FCC regulations require that the following information be provided in this manual: 1. This equipment complies with Part 68 of Federal Communications Commission (FCC) rules and requirements adopted by America’s Carriers Telecommunications Association (ACTA). Each registered interface has a label that contains, among other information, a product identifier in the format US:AAAEQ##TXXXX.
FCC Radio Frequency Interference Statement NetVanta 6355 PoE Hardware Installation Guide FCC Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
NetVanta 6355 PoE Hardware Installation Guide Industry Canada Compliance Information Industry Canada Compliance Information Notice: The Industry Canada label applied to the product (identified by the Industry Canada logo or the “IC:” in front of the certification/registration number) signifies that the Industry Canada technical specifications were met. Notice: The REN for this terminal equipment is supplied in the documentation or on the product labeling/ markings.
Service and Warranty 8 NetVanta 6355 PoE Hardware Installation Guide Copyright © 2011 ADTRAN, Inc.
Table of Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Physical Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Features and Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Power Over Ethernet . . . . . . . . . . . .
Table of Contents 10 NetVanta 6355 PoE Hardware Installation Guide Copyright © 2011 ADTRAN, Inc.
List of Figures Figure 1. Figure 2. Figure 3. Figure 4. Figure 5. Figure 6. Figure 7. Figure 8. Figure 9. Figure 10. Figure 11. Figure 12. Figure 13. Figure 14. Figure 15. Figure 16. Figure 17. NetVanta 6355 PoE Front Panel Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . NetVanta 6355 PoE Rear Panel Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . NetVanta T1/FT1 NIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
List of Figures 12 NetVanta 6355 PoE Hardware Installation Guide Copyright © 2011 ADTRAN, Inc.
List of Tables Table 1. Table 6-1. Table 6-2. Table 6-3. Table 6-4. Table 6-5. Table 6-6. Table 6-7. Table 6-8. Table 6-9. Front Panel LED Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CONSOLE Port Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SFP Slot Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
List of Tables 14 NetVanta 6355 PoE Hardware Installation Guide Copyright © 2011 ADTRAN, Inc.
1. INTRODUCTION This hardware installation guide describes the NetVanta 6355 Power over Ethernet (PoE) unit’s physical characteristics, lists its features and specifications, introduces basic functionality, and provides installation instructions. For information on configuration for a specific application, refer to the configuration guides provided online on the ADTRAN’s Knowledge Base at http://kb.adtran.com.
Physical Description • • • • • • • • • • • • • • • • • • • • • • • • • • NetVanta 6355 PoE Hardware Installation Guide Class of service (CoS) (802.1p) and DiffServ for traffic prioritization with weighted round robin (WRR) and strict priority queuing Four queues per egress port DiffServ-to-802.1p mapping Spanning Tree/Rapid Spanning Tree support (802.1D/802.1w) Storm control, link aggregation (802.
NetVanta 6355 PoE Hardware Installation Guide Physical Description SFP Module Slots The NetVanta 6355 PoE supports two SFP slots that accept a number of industry standard SFP modules. The SFP modules provide Gigabit Ethernet connectivity over fiber for high-speed uplinks or switch stacking.
Physical Description NetVanta 6355 PoE Hardware Installation Guide NetVanta 6355 PoE Front Panel Design The NetVanta 6355 PoE front panel is shown in Figure 1 on page 18. Table 1 on page 19 describes all of the LEDs, and Appendix A on page 41 shows the pinouts for the connectors. NetVanta 6355 PoE Front Panel Features 10/100Base-T Ethernet Interfaces The NetVanta 6355 PoE front panel contains 24 10/100Base-T Ethernet interfaces (RJ-45).
NetVanta 6355 PoE Hardware Installation Guide Physical Description Table 1. Front Panel LED Descriptions LED STAT Port LEDs (1 through 24, G1, G2) SLOT 1/SLOT 2 Power over Ethernet Status LEDs Color Indication Off Unit is not receiving power. Green (solid) Power is on and self-test passed. Green (flashing) On power up, the STAT LED flashes rapidly for five seconds, during which time the user may escape to boot mode from the CONSOLE port.
Physical Description NetVanta 6355 PoE Hardware Installation Guide During power outages, the FXS interfaces are connected directly to the FXO interfaces. This feature is called life line mode, and allows customers to make analog calls even when the power is out. For the NetVanta 6355 PoE, devices connected to the FXS (ANALOG STA) ports must be ACTA/FCC Part 68 compliant due to the direct connection to the public switched telephone network (PSTN) in life line mode. MOH Reserved for future use.
NetVanta 6355 PoE Hardware Installation Guide 3. Option Modules OPTION MODULES The NetVanta 6355 PoE supports several option modules designed to meet a variety of networking requirements. The option modules include plug-in NIMs and VIMs. NIMs/VIMs are cards that plug directly into the option module slot located on the rear of the base unit.
Option Modules NetVanta 6355 PoE Hardware Installation Guide Network Interface Modules NetVanta T1/FT1 NIM (P/N 1202862L1) The NetVanta T1/FT1 NIM (see Figure 3) provides a T1 WAN interface for the NetVanta. This module provides a full T1 or fractional T1 network interface. See Table 6-5 on page 43 for the WAN-T1 connector pinouts. An optional DIM is required for dial backup applications. Dial backup is not supported at this time. WAN-T1 DBU Figure 3.
NetVanta 6355 PoE Hardware Installation Guide Option Modules NetVanta T1/FT1 + DSX-1 NIM (P/N 1202863L1) The NetVanta T1/FT1 + DSX-1 NIM (see Figure 4) provides a T1 WAN interface for the NetVanta, a full or fractional T1 network interface, and a DSX-1 interface. See Table 6-5 on page 43 for the WAN-T1 connector pinouts and Table 6-6 on page 43 for the DSX-1 connector pinouts. An optional DIM is required for dial backup applications. Dial backup is not supported at this time. WAN-T1 DSX-1 DBU Figure 4.
Option Modules NetVanta 6355 PoE Hardware Installation Guide NetVanta Dual T1 NIM (P/N 1202872L1) The NetVanta Dual T1 NIM (see Figure 5) provides two WAN T1 interfaces for the NetVanta. See Table 6-5 on page 43 for the pinouts. An optional DIM is required for dial backup applications. Dial backup is not supported at this time. WAN T1/1 WAN T1/2 DBU Figure 5.
NetVanta 6355 PoE Hardware Installation Guide Option Modules NetVanta E1/FE1 NIM (P/N 1200868E1) The NetVanta E1/FE1 NIM (shown in Figure 6) provides a WAN-E1 interface for the NetVanta 7000 Series, meeting the requirements of ITU-T G.703/G.704. The module provides a single 2.048 Mbps network interface. See Table A-6 on page 43 for the pinouts. An optional DIM is required for dial backup applications. Dial backup is not supported at this time WAN-E1 DBU Figure 6.
Option Modules NetVanta 6355 PoE Hardware Installation Guide NetVanta E1/FE1 + G.703 NIM (P/N 1200878E1) The NetVanta E1/FE1 + G.703 NIM (shown in Figure 7) provides a single WAN-E1 interface (2.043 Mbps) with user-selectable TS0 assignment and a G.703 drop port that can be used to drop and insert traffic to an E1 PBX. See Table A-6 on page 43 for the WAN-E1 pinouts. See Table A-8 on page 43 for the G.703 pinouts. An optional DIM is required for dial backup applications.
NetVanta 6355 PoE Hardware Installation Guide Option Modules NetVanta ADSL NIM, Annex A (P/N 1202869E1) The NetVanta ADSL, Annex A NIM (see Figure 8) adds ADSL capability to the NetVanta. The module provides a single ADSL, ADSL2, or ADSL2+ network interface to support rates up to 25 Mbps. See Table 6-8 on page 43 for the pinouts. An optional DIM is required for dial backup applications. Dial backup is not supported at this time. WAN-ADSL DBU Figure 8.
Option Modules NetVanta 6355 PoE Hardware Installation Guide Voice Interface Modules NetVanta T1/PRI VIM (P/N 1200695L1) The NetVanta T1/PRI VIM (see Figure 9) adds T1 voice capability to the NetVanta. See Table 6-5 on page 43 for the T1 connector pinouts. An optional DIM is required for dial backup applications. Dial backup is not supported at this time. Figure 9.
NetVanta 6355 PoE Hardware Installation Guide Option Modules NetVanta E1/PRI VIM (P/N 1200696G1) The NetVanta E1/PRI VIM (see Figure 10) adds E1 voice capability to the NetVanta. See Table 6-5 on page 43 for the E1 connector pinouts. An optional DIM is required for dial backup applications. Dial backup is not supported at this time. Figure 10.
Option Modules NetVanta 6355 PoE Hardware Installation Guide NetVanta Quad FXS VIM (P/N 1200690E1) The NetVanta Quad FXS VIM (see Figure 11) adds voice capability to the NetVanta. See Table 6-9 on page 44 for the FXS connector pinouts. 1 2 3 4 ANALOG VIM STATIONS Figure 11. NetVanta Quad FXS VIM Features and Specifications Analog Voice Ports Environmental • • • • • Loop Start (LS), Ground Start (GS) Normal and reverse battery operation Transmission Level • • FXS Receive Gain: -12 to +6 dB, 0.
NetVanta 6355 PoE Hardware Installation Guide Option Modules NetVanta Quad FXO VIM (P/N 1202691G1) The NetVanta Quad FXO VIM (see Figure 12) adds voice capability to the NetVanta. See Table 6-9 on page 44 for the FXO connector pinouts. 1 2 3 4 ANALOG VIM TRUNKS Figure 12. NetVanta Quad FXO VIM Features and Specifications Analog Voice Ports Environmental • • • • • Loop Start (LS), Ground Start (GS) Normal and reverse battery operation Transmission Level • • FXO Transmit Gain: -6 to +10 dB, 0.
Option Modules NetVanta 6355 PoE Hardware Installation Guide NetVanta Dual FXS/FXO VIM (P/N 1202692G1) The NetVanta Dual FXS/FXO VIM (see Figure 13) adds voice capability to the NetVanta. See Table 6-9 on page 44 for the FXS/FXO connector pinouts. 1 2 1 2 ANALOG VIM STATIONS TRUNKS Figure 13.
NetVanta 6355 PoE Hardware Installation Guide 4. Unit Installation UNIT INSTALLATION The instructions and guidelines provided in this section cover hardware installation topics, such as mounting options, supplying power to the unit, and installing option cards.
Unit Installation NetVanta 6355 PoE Hardware Installation Guide Mounting Options The unit may be installed in rackmount, wallmount, or tabletop configurations. The following sections provide step-by-step instructions for rack mounting and wall mounting. If you have purchased the VPN Accelerator Card for your NetVanta 6355 PoE, install it first (refer to Installing the NetVanta VPN Accelerator Card (included in P/N 4200368L1) on page 38).
NetVanta 6355 PoE Hardware Installation Guide Unit Installation Wall Mounting the NetVanta By following these instructions exactly, the NetVanta can be safely mounted on the wall. • • • • NetVanta units are to be installed only by qualified service personnel. To avoid damaging the unit, use only the screws included in the shipment when attaching mounting ears to the chassis. When wall mounting the NetVanta, care must be taken not to damage the power cord.
Unit Installation NetVanta 6355 PoE Hardware Installation Guide Figure 14. Wallmount Installation Supplying Power to the Unit The NetVanta 6355 PoE unit comes equipped with an auto-sensing 100 to 250 VAC, 50/60 Hz power supply for connecting to a properly grounded power receptacle. (A detachable power cable with a grounded, three-prong plug comes with the shipment.) To power this unit, connect the power cable to an appropriate AC power source.
NetVanta 6355 PoE Hardware Installation Guide Unit Installation Instructions for Installing the NIMs/VIMs Step Action 1 Remove power from the unit. 2 Remove the cover from the option slot by pulling the pins until they disengage from the chassis. 3 Slide the option module into the option slot until the module is firmly seated against the chassis. 4 Secure the pins at both edges of the module. 5 Connect the cables to the associated device(s). 6 Restore power to the unit.
Unit Installation NetVanta 6355 PoE Hardware Installation Guide Installing the NetVanta VPN Accelerator Card (included in P/N 4200368L1) The optional VPN Accelerator card plugs into a 32-bit PCI slot and is designed to be used in the NetVanta 6355 PoE to provide encryption/decryption and security acceleration services. The card provides the following security services to the host processor: DES, triple-DES (3DES), AES, SHA-1, MD5, and random number generation.
NetVanta 6355 PoE Hardware Installation Guide Unit Installation Installing a CompactFlash Card The CompactFlash (CF) slot supports only the ADTRAN-provided 1 GB CompactFlash card. Follow these instructions when installing a card. The CompactFlash card is hot-swappable and can be inserted or removed while power is applied to the unit. Instructions for Installing a CompactFlash Card Step Action Remove the two screws and the cover from the CF slot on the rear of the unit.
Unit Installation 40 NetVanta 6355 PoE Hardware Installation Guide Copyright © 2011 ADTRAN, Inc.
APPENDIX A. CONNECTOR PIN DEFINITIONS The following tables provide the pin assignments for the base unit, NIMs, and VIMs. Base Unit Pinouts Table 6-1. CONSOLE Port Pinouts Pin Name Description 1 DCD 2 RD Receive Data (output) 3 TD Transmit Data (input) 4 DTR 5 SG 6 DSR 7 — 8 CTS 9 — Data Carrier Detect (output) Data Terminal Ready (input) Signal Ground Data Set Ready Tied to pin 1 (output) Unused Clear to Send Tied to pin 1 (output) Unused Table 6-2.
Appendix A NetVanta 6355 PoE Hardware Installation Guide Table 6-3. 10/100Base-T Ethernet Port Pinouts Pin Name Description 1 TX1 Transmit Positive 2 TX2 Transmit Negative 3 RX1 Receive Positive 4, 5 — 6 RX2 7, 8 — Unused Receive Negative Unused Table 6-4.
NetVanta 6355 PoE Hardware Installation Guide Appendix A Network and Voice Interface Module Pinouts Table 6-5. T1/E1 Connector Pinouts Pin Name Description 1 R1 Receive data from the network–Ring 1 2 T1 Receive data from the network–Tip 1 3 — Unused 4 R Transmit data toward the network–Ring 5 T Transmit data toward the network–Tip 6-8 — Unused Table 6-6.
Appendix A NetVanta 6355 PoE Hardware Installation Guide Table 6-9. Analog Station (FXS) and Analog Trunk (FXO) Port Pinouts 44 Pin Name Description 1, 2 — 3 Ring 4 Tip Tip lead of the 2-wire interface 5, 6 — Unused Unused Ring lead of the 2-wire interface Copyright © 2011 ADTRAN, Inc.
Index Numerics N 10/100Base-T interface 20 1000Base-LX single-mode SFP module 17 1000Base-SX multi-mode SFP module 17 network interface modules (NIMs) ADSL, Annex A 27 Dual T1 24 E1/FE1 25 E1/FE1 + G.703 26 installation 36 modules supported 17 option slots 19 T1/FT1 22 T1/FT1 + DSX-1 23 C CLI 33 command line interface 33 CompactFlash 19, 39 console 20 D door relay 20 Dual FXS/FXO VIM 32 Dual T1 NIM 24 O option modules discussion 21 P E E1/FE1 + G.
Index T T1, dual NIM 24 T1/FT1 + DSX-1 NIM 23 T1/FT1 NIM 22 V voice interface modules (VIMs) Dual FXS/FXO 32 E1/PRI 29 installation 36 46 NetVanta 6355 PoE Hardware Installation Guide modules supported 17 option slots 19 Quad FXO 31 Quad FXS 30 T1/PRI 28 VPN accelerator card 38 W wall mounting instructions 35 warranty 7 Copyright © 2011 ADTRAN, Inc.