Datasheet

jobAid
DESCRIPTION
TheSmallForm‐FactorPluggable10GigabitEthernetXFP,1550
nm,CommercialTemperature(XFP)opticaltransceiverisafully
duplexserialelectric,serialopticdevicewithbothtransmitand
receivefunctionscontainedinasinglemodulethatprovidesa
highspeedseriallinkat10Gb/s.Installedintoanappropriate
host
module,theXFPprovidesa10Gigabitinterfacetothe
supportingsystem.
ThetransmitsideoftheXFPconvertsserialNRZelectricaldateat
the10Gb/slineratetoastandardcompliantopticalsignal.The
receivesideoftheXFPconvertstheincomingDCbalancedserial
NRZopticaldataatthe
10Gb/slinerateintoserialelectricaldata.
NOTE
Toensurecompatibility,refertothedoc umentationpr ovided
withthehostmodule.
ThefollowingfeaturesaresupportedontheXFP:
♦ 1550nmopticalsignalsforupto80kmreach
♦ Lowpowerconsumption(<3.5Wmax)
♦ ExcellentEMIperformance
♦ Biterrorrate10^‐12
CAUTION
!
Duetocompliancecertificationrequirements,onlyXFPssupplied
byADTRANaretobeusedwiththehostmodule.ADTRAN
cannotcertifysystemintegritywithotherXFPs.
Operational Specifications
♦ OpticalSpecifications:
◊ TransmitWavelength:1550nm
◊ ReceiveWavelength:1530to1565nm
◊ Datarate:9.95Gb/sto11.1Gb/s
◊ Opticaltransmitlevel:0to+4.0dBm
Small Form-Factor Pluggable
10 Gigabit Ethernet XFP, 1550 nm
Commercial Temperature
◊ Opticalreceivelevel:greaterthan–24dBm
◊ Opticaldistance:80kmmaximum
◊ Opticalconnectors:LC
♦ ExtendedEnvironmentalSupport:
◊ Operationaltemperaturerange:0°Cto+70°C
◊ Storagetemperaturerange:–40°Cto+85°C
◊ Relativehumidityto85%,noncondensing
INSTALLATION
InspecttheXFP.Ifdamaged,fileaclaimwiththecarrierandthen
contactADTRANCustomerService.
ToinstalltheXFPintoanappropriatemodule,completethe
followingsteps:
1. InserttheXFPintotheXFPcageonthecircuitboardofthe
hostmodulewiththelatchhandlefacingoutward.Slidethe

XFPallthewayintothereceptacle.
NOTE
ThelatchontheXFPisforremovalonly.WhenremovingtheXFP,
rotatethelatchawayfromtheXFPcageuntilaphysicalclick
occurs.TheXFPshouldslideeasilyoutofthecage.
2. Usingthumbandforefinger,exertadequatepressureto
ensuretheXFPiscompletelyseatedintheXFPcage.
3. Donotremovetheconnectorpluguntiltheopticalfiber
connectionismade.
NOTICE
Itisrecommendedthattheconnectorplugremainonwhenever
thetransceiveropticalfiberconnectorisnotinserted.
4. Continuetheinstallationandturn‐upofthehostmodule
usingtheinstructionsintheJobAidprovidedwiththat
module,orusingtheInstallationandMaintenancePractice
(I&M),availableonlineatwww.adtran.com.
PROVISIONING
TheXFPisnotdirectlyprovisionable.ToprovisiontheXFP,
accessthemenusystemofthehostmodule.Refertothe“Provi‐
sioning”sectionoftheJobAidorInstallationandMaintenance
Practiceprovidedwiththehostmoduleforprovisioningdetails.
CLEI: BVL3AGKD_ _
Product P/N: 1442980G1C
Issue Date: 0909
Document P/N: 61442980G1C-22A