FCC ID: P27SCD2R0 SCD2R0-29 Wireless FHD Doorbell Camera Setup Guide
FCC ID: P27SCD2R0 Copyright 2019. All Rights Reserved. Document Version: 1.
FCC ID: P27SCD2R0 Table of Contents Chapter 1 Introduction .......................................................................................................... 1 Package Contents .............................................................................................................. 1 Physical Details .................................................................................................................. 2 Chapter 2 Setup ...............................................................
FCC ID: P27SCD2R0 Chapter 1 Introduction 1 This section provides information about the Doorbell Camera features, components and capabilities.. Package Contents The following items should be included: If any of these items are damaged or missing, please contact your dealer immediately. 1. Doorbell Camera x 1 2. Screw/Anchor x 2 3.
FCC ID: P27SCD2R0 Physical Details The SCD2R0-29 supports both analog and digital chimes within 8-24 AC voltage range. The operation temperature of SCD2R0-29 with regular mounting bracket and Battery pack is –4°F to 122°F (–20°C to 50°C). As to SCD2R0-29 with Always on bracket, the operating temperature is –4°F to 104°F. (–20°C to 40°C) on day mode and –4°F to 95°F. (–20°C to 35°C) on night mode. Note: 1.
FCC ID: P27SCD2R0 Rear Panel Reset Button When pressed and held over 10 seconds, the LED will be solid amber, which means the settings of camera will be set to their default values. On/Off Switch Use this switch to turn on/off the device. Micro USB Connector This connector is used for charging the power. Connect the supplied Micro-USB cable to this port.
FCC ID: P27SCD2R0 LED Activity & Behavior Doorbell Activity LED Color LED Behavior Description Factory Reset Amber Solid Press the reset button for 10 seconds to start this process. WPS Pairing (PIN Code Mode) Amber Blinking (200ms) When doorbell button is held down for more than 3 seconds, the LED will start flashing amber indicating doorbell camera is trying to connect to your Wi-Fi network in Pin Code mode.
FCC ID: P27SCD2R0 Chapter 2 Setup This Chapter provides details on how to install and configure the Doorbell Camera. 2 System Requirements • A computer with Internet access • You can use the following web browser while using a computer: • Internet Explorer 10 or later • Firefox 3.5 or later • Safari 3 or later (Mac OS X only) • Chrome • Microsoft Edge Installation 1.
FCC ID: P27SCD2R0 b. 1) WPS PBC Mode：Press the Doorbell button for less than 3 second and on your Wireless device (AP or router) as well to establish a wireless connection automatically. The wireless connection is successful when the Green LED blinking. 2) WPS Pin Code Mode：Key in the PIN code of Doorbell’s back label on the Client PIN code of AP, and then held down Doorbell button for more than 3 seconds, the Doorbell Camera will be in the WPS Pin Code mode.
FCC ID: P27SCD2R0 g. Video will start playing automatically. There may be a delay of a few seconds while the video stream is buffered. h. If the Administrator has restricted access to known users, you will then be prompted for a username and password. Enter the name and password assigned to you by the Doorbell administrator. The default log in Administration: User Name: administrator Password: Blank i. 3. Access the Administration for more Doorbell settings on SCD2R0-29 GUI.
FCC ID: P27SCD2R0 4. 5. If your existing doorbell produces an electronic sound that is programmable and comes in the form of a unique sound, it's a digital chime. If it has a traditional "ding dong" sound, it's a compatible analog chime. Complete the pairing process and unplug the Micro USB cable from the Doorbell Camera. 3 Identify the location for Mounting the Doorbell Camera The recommended installation height of the Doorbell Camera is about 130~150cm from the ground.
FCC ID: P27SCD2R0 4. 5. Choose either the Always On bracket or the regular mounting bracket that will cover the hole of the legacy doorbell button. Please check Always On Bracket Installation section for more details Connect the power wires from the existing doorbell to the screw terminals of the bracket. 6. Secure the bracket with screws. Note: Install the anchors if necessary. The provided lever can be used for measuring angles to prevent inclination. 7.
FCC ID: P27SCD2R0 8. 9. Turn on the breaker circuit. Check that the chime is working normally by pushing the doorbell button. If the AC wires are not connected properly, the LED will blink amber every 5 seconds.
FCC ID: P27SCD2R0 Power Kit Installation The Power Kit included with the doorbell camera is a small device, which support Doorbell with any kinds of analog and digital chime usage by going between the doorbell transformers and chime wiring. Note: Before removing or attaching wires to your original bell, be sure that the power is turned off at the breaker box. Consult a licensed electrician if needed. 1. Turn off the circuit breaker for the indoor chimer. 2. Remove the cover from the indoor chimer. 3.
FCC ID: P27SCD2R0 Always On Bracket Installation (Optional) The Always On bracket (may not included in the package) can only be installed with mechanical doorbell chimes (AC16V~24V). In this configuration, the doorbell camera will be in always on mode, which brings back the 5 second pre-buffer, connects live view faster, and removes the need for the internal battery to be charged. 1. Use the always on bracket that will cover the hole of the legacy doorbell button. 2.
FCC ID: P27SCD2R0 4. Attach the doorbell camera to the mounting bracket. Make sure the doorbell camera is firmly fixed and working properly. Caution: To avoid damaging the rubber seal of the pogo pins, please attach the camera to the mounting bracket flush. Mounting bracket should lay flat against the wall. Over torqueing can warp the bracket and cause it to lose contact with pins.
Appendix A Specifications A Wireless Doorbell Camera Model Wireless 2-Way Doorbell Camera Dimensions (H x W x D) 126 mm * 42.7mm * 35.2mm (4.96 x 1.68 x 1.39) Operating Temperature Mounting Bracket and Battery Pack mode: -20°C to 50°C Always On Bracket mode: -20ºC to 40ºC ( Day Mode) -20ºC to 35ºC ( Night Mode) Storage Temperature -20° C to 45° C Network Protocols TCP/IP, HTTP, HTTPS, DHCP, uPnP, NTP, RTP, RTCP, RTSP, DN Wireless 802.
Regulatory Approvals FCC Statement This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
