ADT Pulse® Interactive Solutions iCamera-1000-ADT Indoor Low-Light Camera Installation Guide
ADT Pulse® Interactive Solutions iCamera-1000-ADT Indoor Low-Light Camera Installation Guide Table of Contents WELCOME ..................................................................................................................... 1 Overview ....................................................................................................................... 1 iCamera-1000-ADT Features ................................................................................... 1 Package Contents ............
ADT Pulse® Interactive Solutions iCamera-1000-ADT Indoor Low-Light Camera Installation Guide Welcome This installation guide provides step-by-step instructions for configuring and installing your iCamera-1000-ADT Indoor Low-Light camera to your ADT Pulse® wireless network. (Permanent mounting instructions for the iCamera are also included.) Overview The iCamera-1000-ADT monitors your home or business in a low light or dark environment.
ADT Pulse® Interactive Solutions iCamera-1000-ADT Indoor Low-Light Camera Installation Guide Package Contents 1. The iCamera-1000-ADT Indoor Low-Light Camera 2. Stand 3. Y-Cable 4. PoE Cable 5. 12V Power Adapter 6. Assembly Back Plate with three screws (packaged separately) 7. Wall Mount Plate 8. Two Mounting Screws 9.
ADT Pulse® Interactive Solutions iCamera-1000-ADT Indoor Low-Light Camera Installation Guide Physical Details – iCamera-1000-ADT Front Panel Figure 1: Front Panel 1. Light Sensor Detects lighting conditions. 2. IR LEDs The LEDs help you see clearly at night or in a dark environment. 3. Day Camera Lens The Day Camera Lens is used in a bright environment. 4. Night Camera Lens The Night Camera Lens is used in a dark environment. 5. Power/Wi-Fi On (Green) - Power on. Off - Power off.
ADT Pulse® Interactive Solutions iCamera-1000-ADT Indoor Low-Light Camera Installation Guide Rear Panel Figure 2: Rear Panel 1. LAN Port Use in conjunction with the supplied LAN cable to connect your iCamera to the ADT Pulse Gateway. 2. Stand Mount The stand mount connects the stand to the iCamera. 3. Reset Button The reset button has two (2) functions: Reboot. When the reset button is quickly pressed then released, the iCamera reboots. Clear All Data.
ADT Pulse® Interactive Solutions iCamera-1000-ADT Indoor Low-Light Camera Installation Guide Configuring and Installing the iCamera-1000-ADT The following instructions provide details of configuring and installing the iCamera-1000-ADT Indoor Low-Light Camera to your ADT Pulse network. Initial setup is done only one time to configure the iCamera’s wireless settings to the ADT Pulse Gateway. Figure 3: Initial Setup 1. Connect the LAN Cable to the iCamera a.
ADT Pulse® Interactive Solutions iCamera-1000-ADT Indoor Low-Light Camera Installation Guide Adding the iCamera-1000-ADT to your ADT Pulse Wireless Network 1. Open your web browser. In the address bar, type: https://Portal.ADTPulse.com. 2. Type your Username and Password, and then click the Sign In button. 3. Click the System tab, and then click the Manage Devices button.
ADT Pulse® Interactive Solutions iCamera-1000-ADT Indoor Low-Light Camera Installation Guide 4. In the Manage Devices Assistant, click Cameras. 5. Click the picture of the iCamera or select it from the drop-down list, and then click the Continue button.
ADT Pulse® Interactive Solutions iCamera-1000-ADT Indoor Low-Light Camera Installation Guide 6. Assign the iCamera a unique name (this is usually based on the location of the iCamera) in the space provided, and then type the iCamera’s MAC ID or Server Name. 7. Click the Continue button. 8. Connect the camera to the Device Port of the gateway using the Ethernet cable (attached to the Y-Cable.
ADT Pulse® Interactive Solutions iCamera-1000-ADT Indoor Low-Light Camera Installation Guide 9. Connect the supplied 12V power adapter to power up the iCamera, and then click the Continue button. NOTE 9 Please wait several minutes while the iCamera is being added to the network.
ADT Pulse® Interactive Solutions iCamera-1000-ADT Indoor Low-Light Camera Installation Guide 10. Click Finish after installation is complete. Figure 4: Installation Using POE Cable 11. Unplug the Y-cable from the ADT Pulse Gateway, and then power off the camera. IMPORTANT 10 IF CAMERA WILL BE INSTALLED AS A ‘WIRED’ CAMERA, USE THE LAN CABLE AND THE Y-CABLE. (REFER TO FIGURE 3 ON PAGE 5 OF THIS GUIDE.) IF CAMERA WILL BE INSTALLED AS A ‘WIRELESS’ CAMERA, USE THE POE CABLE TO SUPPLY POWER TO THE CAMERA.
ADT Pulse® Interactive Solutions iCamera-1000-ADT Indoor Low-Light Camera Installation Guide iCamera Wall Mounting Instructions NOTE Ensure that the iCamera is properly configured and added to the network before mounting the camera.* 1. Stand Placement Locate an area where you want the iCamera to be mounted. Using the wall plate as a template, make two small marks inside the mounting holes of the wall plate. 2.
ADT Pulse® Interactive Solutions iCamera-1000-ADT Indoor Low-Light Camera Installation Guide iCamera Wall Mounting Instructions (Cont’d) 4. Hook the two mounting holes on the stand into the mounting screws. 5. Attach the iCamera Stand Locate the stand mount on the back of the iCamera. Fasten the stand by turning the iCamera counterclockwise until secured. 6. Mounting the iCamera Connect the PoE cable into the LAN port of the device. 7.
ADT Pulse® Interactive Solutions iCamera-1000-ADT Indoor Low-Light Camera Installation Guide iCamera Wall Mounting Instructions (Cont’d) 8. Connect the Power Adapter Connect the supplied power adapter to the PoE cable and power up. 9. Check the LEDs The Power LED turns on briefly, and then starts blinking for approximately 15 to 20 seconds. After startup is completed, the Power LED should remain ON. The Network LED should be ON.
ADT Pulse® Interactive Solutions iCamera-1000-ADT Indoor Low-Light Camera Installation Guide PIR Video Motion Detection The motion event will be captured when a significant image changes within the Window of Interest. The Window of Interest is defined below. The following installation hints should be noted: 1. Take care not to install facing direct sunlight, bodies of water, or areas of moving shadows as these can lead to unintended triggers. 2.
ADT Pulse® Interactive Solutions iCamera-1000-ADT Indoor Low-Light Camera Installation Guide Enabling Motion Detection via the ADT Security System 1. Click the Automations tab, and then click the Add Automation button. 2. Select a trigger for this automation from the Trigger drop-down list. 3. Select Motion from the Event drop-down list. 4. Select the conditions under which you want the automation action to occur from Active drop-down list. 5. Click Add Actions. 6.
ADT Pulse® Interactive Solutions iCamera-1000-ADT Indoor Low-Light Camera Installation Guide 8. Click OK. 9. Click Save.
ADT Pulse® Interactive Solutions iCamera-1000-ADT Indoor Low-Light Camera Installation Guide Appendix A Specifications Model iCamera Dimensions 72mm (W) x 72mm (H) x 20mm (D) (without stand) Operating Temperature Outdoor: -20 C to 45 C Video compression H.
ADT Pulse® Interactive Solutions iCamera-1000-ADT Indoor Low-Light Camera Installation Guide CE Approvals The iCamera and the Ethernet iCamera meet the guidelines of the European Union and comply with the 99/5/EEC and RTTE 99/5EG directives, including the following standards: EN60950 EN300 328-2 EN301 489-1 EN301 489-17 This is a Class B product. In a domestic environment, this product may cause radio interference in which case the user may be required to take adequate measures.
