Version 2.
Industrial PCs OPC5112 Product Portfolio Copyright © ads-tec GmbH Raiffeisenstr.14 D-70771 Leinfelden-Echterdingen Germany 2 © ads-tec GmbH • Raiffeisenstr.
Industrial PCs OPC5112 INDEX 1 REMARKS ............................................................................................................................... 5 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2 SAFETY INFORMATION .......................................................................................................... 8 2.1 2.2 2.3 2.4 2.5 3 FRONT CONTROL BUTTONS ...........................................................................................................
Industrial PCs OPC5112 8.9 EXTERNAL DRIVES ...................................................................................................................... 21 8.10 DVI INTERFACE...................................................................................................................... 22 8.11 HARD DRIVE / COMPACTFLASH (IDE INTERFACE) ............................................................................ 23 8.12 PS/2 CONNECTION ...........................................................
Industrial PCs OPC5112 1 REMARKS 1.1 RELEVANT DEVICE DOCUMENTATION Consult the following documentation for information pertaining to device setup and operation: User manual on the service CD (this documentation): Contains information pertaining to device mounting, startup and operation as well as the technical data for the device hardware. Service CD: Contains drivers, user manual and installation instructions for installing drivers, calibration and using the touch screen. 1.
Industrial PCs OPC5112 1.5 COPYRIGHT This manual and any illustrations contained therein are copyrighted. Any use of this manual which deviates from the copyright stipulations is prohibited. Reproduction, translation and/or electronic and photographic archiving and modification require written permission from ads-tec GmbH. The violation of these rights will be prosecuted. 1.6 AMBIENT CONDITIONS The device can be operated in the following ambient conditions.
Industrial PCs OPC5112 1.7 STANDARDS The device meets the requirements and objectives of the following EC directives: • • The device complies with the test specifications for the CE label according to the European test standards EN 55022 and EN 50082-2. The device complies with the test specifications DIN EN 60950 (VDE 0805, IEC 950) "Safety of Information Technology Equipment". • The device complies with the DIN EN 60068-2-6 (sinusoidal vibration) test specifications.
Industrial PCs OPC5112 2 SAFETY INFORMATION The device is electrically charged and contains highly sensitive components. Permissible modification by the user is limited to installing add-on cards. The manufacturer or a service provider authorized by the manufacturer should be consulted if any other modifications are to be carried out. Whenever such modifications are carried out the device must first be switched off and the power cable must be disconnected.
Industrial PCs OPC5112 2.2 DAMAGE DUE TO IMPROPER USAGE If the control system shows obvious damage caused by incorrect operational and/or storage conditions or improper handling, then the device is to be shut down immediately and protected against unintentional startup. 2.3 WARRANTY AND REPAIRS During the warranty period, repairs may only be carried out by the manufacturer or persons authorized by the manufacturer. 2.
Industrial PCs OPC5112 3 MOUNTING 3.1 MOUNTING OPTIONS The device is intended for installation in control panels and cabinet doors. The control panels and consoles should be accessible from the back for mounting and operation (plug connectors). The device can be installed in control cabinets with wall thicknesses of 2...7 mm. We recommend at least 3 mm for proper mounting with front IP65 protection.
Industrial PCs OPC5112 3.3 MOUNTING PROCEDURE • Cut out the section or the control panel or cabinet door as shown in the illustration. • Slide the device into the cutout from the front (place the ON/OFF switch of an OPC with 24 V DC to the center position). • Insert the fastening bolts with slot nuts in the matching slots in the sheet metal cover and then tighten the screws on all bolts equally (max. torque 25 Ncm) until the faceplate is pulled into place in the cutout.
Industrial PCs OPC5112 4 ADD-ON CARD INSTALLATION 4.1 PRE-INSTALLATION NOTES The user can install ISA bus or PCI bus add-on cards such as network or fieldbus cards in the device. The card slots are accessed by taking off the back cover (only one slot in 511X). The screws on the back of the control system should be removed for this purpose. Warning: The components in the device are highly sensitive products, which can be destroyed or impaired by improper handling.
Industrial PCs OPC5112 5 STARTUP Warning: The PC should be switched off before disconnecting plugs in order to avoid damage to electronic components! In order to avoid formation of condensation, the device should only be switched on once it has acclimated to the room temperature. Pay attention to the voltage permitted for the device. You should allow five seconds to pass between switching the device off and switching it back on.Do not remove the cover with force. 5.
Industrial PCs OPC5112 5.2 CABLE INSTALLATION The device interfaces and power supply plug are found on the side of the casing. The free slots and the drives are found in the same place. 5.3 5.4 14 STARTUP PROCEDURE • For 230 V AC device: Insert the power cable in the IEC connector and connect it to the power source. • For 24 V DC device: Place the cable end sleeves of the power cable wires in the terminals.
Industrial PCs OPC5112 6 OPERATION 6.1 FRONT CONTROL BUTTONS Depending on the device model, factory settings will include an operating system (Windows CE.net, Windows XP embedded or Windows XP Professional) and a software keyboard. The buttons on the front have already been assigned the following functions in the software keyboard by a special driver: Level 1: Displaying and closing the software keyboard to enter characters via the touch screen.
Industrial PCs OPC5112 6.2 SOFTWARE KEYBOARD If the factory settings include the operating system, then the software keyboard will be installed as well. If the factory settings do not include the operating system, then the software keyboard still has to be installed. The software keyboard can be used to enter data using the touch screen as you would with an external keyboard. Operating the software keyboard version 3.
Industrial PCs OPC5112 6.3 EXTERNAL KEYBOARD The control system has a 6-pin PS/2 connector labeled "keyboard". Standard AT compatible keyboards with the appropriate plugs can be connected here. Proper functioning of a keyboard is to be tested before use. Note: Cherry keyboards are preferred because the timing of the integrated controller is tuned to these devices. While the software keyboard is displayed on the screen, the external keyboard function is limited.
Industrial PCs OPC5112 7 STATUS INDICATORS 7.1 SYS LED (TWO COLORS) Various different device states are displayed by the color and flashing patterns of the SYS LED. The following signals are indicated: • • • 18 LED green LED orange LED off Device is on (power on). The switch for changing the display setting is pressed. The device is off. (power off). © ads-tec GmbH • Raiffeisenstr.
Industrial PCs OPC5112 8 INTERFACES 8.1 INTERFACE CONFIGURATION INTERFACE COM1 COM2 COM3 LPT 8.2 IRQ 4 3 11 7 ADDRESS 3F8h 2F8h 03E8 378h INTERFACE ASSIGNMENT The interfaces are found on the left side of the casing (as seen from the front). All interfaces are labeled. The IEC connector or the lead out terminal for the power supply is found on the right side of the control system. Note: When using the embedded operating system Windows CE.net, the communication interfaces (COM, USB, etc.
Industrial PCs OPC5112 8.4 115/230 V AC POWER R SUPPLY An IEC connector is used as a power supply. The provided d cable should be used to connect the device. Power supply unit te echnical data • • • • Power consu umption: Input voltag ge: Current consumption: Max. switch-on current: Max. 150 Watts 90…260 V AC 4A (115V) / 2A (230V) 30A (115) / 60A (230V) Note: The device's typicaal power input is listed in the "Technical Details" section. s 8.
Industrial PCs OPC5112 8.6 NETWORK CONNECTION (RJ45) If the required drivers are installed on the device, the control system can be integrated in an Ethernet network with 10/100 Mbit support using the Ethernet 10/100BaseT network connector and a suitable network cable. The specifications of the underlying network topology are to be adhered to. The drivers required to use this function can be installed from the provided service CD if needed. 1 8.
Industrial PCs OPC5112 8.10 DVI INTERFACE The DVI Interface iss used to transfer analog video signals. It is possible to connect a VGA display by using a su uitable DVI-VGA adapter. Note: The Interface of the t Panel PC works like a DVI-A Interface. transferred analog. g.
Industrial PCs OPC5112 8.11 HARD DRIVE / COMPAC CTFLASH (IDE INTERFACE) The choice of storag ge media depends on individual customer requirrements. The following storage options are available: CompactFlash: his option implements a CompactFlash card with a capacity of at least Th 12 28 MB. The capacity should be chosen depending g on the required op perating system and additional programs to be in nstalled. Hard drive: Th his option implements a 2,5" Festplatte mind. 30 GB G (UDMA).
Industrial PCs OPC5112 9 SOFTWARE/DRIVER INSTALLATION The device is provided with a preinstalled Windows operating system if requested by the customer. The drivers required for this are configured and the operating system is activated by entering the licensing information. If you have to reinstall the operating system, please proceed as follows.
Industrial PCs OPC5112 9.2 TOUCH SCREEN DRIVER INSTALLATION Note: When installing drivers, please note that the touch screen is connected to the serial interface! The touch screen and the PS/2 mouse can be used simultaneously Installation is to be carried out as described in the following: • Switch on and boot the PC • Use the Explorer to access the service CD and then launch the installation file in the touch screen directory. • Follow the instructions on the screen and accept the licensing agreement.
Industrial PCs OPC5112 10 TECHNISCHE DETAILS 10.1 DISPLAY DATA Display 12.1" TFT, 800 x 600 Pixel Displayable colors max. 256k colors TouchScreen Resistive industrial touch screen 10.2 COMPUTER TECHNICAL DATA The device can be furnished with the following adsX modules (depending on customer requirements). Version 1 Pentium M 1.6 GHz with fan 256MB - 2GB DDR RAM Intel 855 GME Version 2 Pentium M 1.1 GHz 256MB - 2GB DDR RAM Intel 855 GME Version 3 Celeron M 1.
Industrial PCs OPC5112 11 SERVICE AND SUPPORT ads-tec and its partners provide customers a comprehensive range of services and a competent support team for quick response to all questions concerning ads-tec products and assemblies. ads-tec devices are also deployed by partner companies and can therefore be customized to meet individual customer needs. Only the system manufacturer can respond to questions pertaining to special configurations and software installations in each case.
