Version 1.
IPC1300 1 Index 1 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2 2.1 2.2 2.3 2.4 2.5 3 3.1 3.2 3.3 3.4 4 4.1 4.2 4.3 5 5.1 5.2 5.3 5.4 5.
IPC1300 6 Interfaces 6.1 6.2 6.3 6.4 6.5 6.6 6.7 7 Interface Configuration 24V DC Power Supply 230V AC Power Supply USB‐Interfaces Network conncetion (RJ45) Serial COM Interface (RS232) DVI‐ Interface Drives 7.1 7.2 7.3 2 15 15 15 15 16 16 17 18 19 Hard Drive / Compact Flash External Drives Temperature Monitoring 19 19 19 8 Software‐/Driver‐Installation 20 9 Technical Details 21 10 10.1 10.2 Service & Support 22 ads‐tec Support Company adress 22 22 © ads‐tec GmbH • Raiffeisenstr.
IPC1300 3 1 Remarks 1.1 Relevant Documentation for this device The following documents are essential for setting up and operating this device: User Manual (This Documentation): Contains information for installation, commissioning and operating the device along with technical data of the device hardware. Qucik Start Guide: Quick Install Guide for fast commissioning. 1.
IPC1300 4 1.5 Copyright This manual, including all contained figures, is protected by copyright law. Any use for third parties non‐ compliant with the copyright provisions is prohibited. Any reproduction, translation as well as electronic and photographic archiving and modification shall only be permitted after explicit written authorisation by ads‐tec GmbH. Any party in violation of this provision shall be obliged to damage compensation. 1.
IPC1300 5 1.7 Standards This device complies with the requirements and protective aims of the following EC regulations: Standards This device meets the test requirements for granting the CE sign according to the European test standards EN 61000‐6‐4 and EN 61000‐6‐2 This device complies with the test requirements in accordance with EN 60950 (VDE0805, IEC950) "Safety of Information Technology Equipment" The device meets the EN 60068‐2‐6 test requirements (sinus excitation).
IPC1300 6 2 Notes on Operation & Safety This device contains electrical voltages and extremely sensitive components. Intervention by the user is only designated for establishing the required cable connections. The manufacturer or a service partner authorised by the manufacturer should be consulted if you plan to make further modifications. Before beginning any works on this device, it must be disconnected from the power supply.
IPC1300 7 2.2 Damage Caused By Improper Use This device must immediately be shut down and protected from any accidental commissioning if the operating system shows any obvious damage caused by, for example, improper operating or storage conditions, or by improper use or handling. 2.3 Warranty / Repair During the warranty period, any repair must only be carried out by the manufacturer or by a person authorised by the manufacturer. 2.
IPC1300 8 3 Mounting 3.1 Mounting options The device is intended for installation on control panels. If the device is mounted somewhere else, then the required ambient conditions should always be provided. Warning: The device must be switched off before connecting or disconnecting any cables in order to prevent damage to the electronics! The device may only be switched on after acclimatising to the ambient temperature in order to avoid condensate accumulation.
IPC1300 3.2 Device mounting illustration IPC1300 (24V DC Abb. 1: © ads‐tec GmbH • Raiffeisenstr.
IPC1300 3.3 Device mounting illustration IPC1300 (230V DC) Abb. 2: © ads‐tec GmbH • Raiffeisenstr.
IPC1300 11 3.4 Mounting procedure Use the drilling template to drill holes according the mounting illustration in the control panel with the specified threading. Insert the upper screws half way into the control panel and hang the device on the mounting links. Tighten the screws and insert the rest of the screws.
IPC1300 12 4 Add‐On Card Installation 4.1 Pre‐installation notes The user can install CompactFlash or PCI add‐on cards such as Interbus cards in the device. The card slot is accessed by taking off the back cover. The crosshead screws on the back of the control system should be removed for this purpose. Achtung: The components in the device are highly sensitive products, which can be destroyed or impaired by improper handling. The same applies to the PC add‐on cards to be installed.
IPC1300 13 5 Startup Warning: The PC should be switched off before disconnecting plugs in order to avoid damage to electronic components! In order to avoid formation of condensation, the device should only be switched on once it has acclimated to the room temperature. Pay attention to the voltage permitted for the device. You should allow five seconds to pass between switching the device off and switching it back on.
IPC1300 14 5.4 Check of Readiness for Operation Check the device for any hidden damage caused by improper transport, improper operating or storage conditions or by improper use (e.g. smoke development from the device, etc.). Immediately shut down the device and prevent any further accidental commissioning if any damage is detected. os: 21 /Datentechnik/Bedienung/Softkeyboard/Softkeyboard für VMT 60xx @ 1\mod_1228750145198_6.
IPC1300 15 6 Interfaces 6.1 Interface Configuration Interface IRQ Adress COM1 4 3F8h Pos: 26 /Datentechnik/Schnittstellen/Spannungsversorgung/Spannungsversorgung für VMT60xx-Serie @ 2\mod_1260450284020_6.doc @ 6853 @ 6.2 24V DC Power Supply The supply voltage is provided via a lead‐through terminal including a screw connection. (The figure shows the socket inside the device) Pin‐Number Signal‐Name 1 24V DC 2 PE 3 0 V DC Technical Data Power Supply •Power Consumpion: Max.
IPC1300 16 6.4 USB‐Interfaces The USB interfaces are used for connecting peripherals with USB connection. The interface complies with the USB 2.0 standard. Pin‐Nummer Signal‐Name 1 VDC 2 D‐ 3 D+ 4 GND Hinweis: The USB interfaces may be locked using the Lock USB software tool. You'll find this software and the documentation on the service CD. Pos: 30 /Datentechnik/Schnittstellen/PS2/Kombi Buchse für VMT 60xx @ 2\mod_1268840073235_6.
IPC1300 17 6.6 Serial COM Interface (RS232) The serial interface is used for digital and for analogue data transmission as well. The RS 232 interface can be connected by using a commercially available 9‐pin SUB‐D cable. Pin‐Number Signal‐Name 1 DCD 2 RxD 3 TxD 4 DTR 5 GND 6 DSR 7 RTS 8 CTS 9 RI Note: This interface is not electrically isolated. © ads‐tec GmbH • Raiffeisenstr.
IPC1300 18 6.7 DVI‐ Interface The DVI‐Interface is used to transfer analog and digital video signals. A DVI‐I Cable is required to connect a digital display to the device. It is also possible to connect a VGA display by using a suitable DVI‐VGA adapter Note: The DVI‐Interface is a Single Link Interface.
IPC1300 19 7 Drives 7.1 Hard Drive / Compact Flash The choice of storage media depends on individual customer requirements. The following storage options are available: Hard drive/SSD: This option implements a 2,5" Festplatte mind. 60 GB (SATA). The hard drive is formatted using the NTFS file system (Windows XP default). Note: Recommendations for choosing the storage medium for a basic installation: CompactFlash: Windows CE.
IPC1300 20 8 Software‐/Driver‐Installation The device will be delivered with a pre‐installed Windows operating system on request by the customer. The drivers required for this are already installed, and the operating system will be enabled by entering the licence information. Should an initial installation be required, please adhere to the following steps.
IPC1300 21 9 Technical Details Device Data IPC1300 Processor Celeron™ 1,2Ghz / Core™ 2 Duo 2,26GHz RAM Graficsmemory 2GB RAM / 4 GB RAM 7 Mass storage max. 256 MB shared 2,5“ Automotive Hard Disk min. 60GB (SATA) or 2,5“ SSD Interfaces 1 x COM 1 (RS232) 1 x COM 2 (RS232) 1 x DVI‐I 6 x USB 2.0 Network 4 x Ethernet (10/100/1000 MBit) RJ45 Slots 2 x PCI, 1 x PCI express Protection class IP20 External Device Dimensions (W x H x T) 288 x 118 x 270 mm Weight Power consumption Max.
IPC1300 22 10 Service & Support ads‐tec and its partner companies offer your customers a comprehensive service and support, which ensures availability of a fast and competent support with respect to all upcoming questions related to ads‐tec products or assemblies. Since the devices manufactured by ads‐tec are also used by associate companies, these devices might be configured in customer specific ways.
