Version 1.
Industrial PCs BPC1000 Product Portfolio Copyright © ads-tec GmbH Raiffeisenstr.14 D-70771 Leinfelden-Echterdingen Germany 2 © ads-tec GmbH • Raiffeisenstr.
Industrial PCs BPC1000 INDEX ABOUT US .......................................................................................................................................... 5 1 REMARKS ................................................................................................................................. 6 1.1 RELEVANT DEVICE DOCUMENTATION ............................................................................................. 6 1.
Industrial PCs BPC1000 7 TECHNICAL DETAILS ................................................................................................................. 23 7.1 COMPUTER DATA ................................................................................................................... 23 7.2 GENERAL DATA ...................................................................................................................... 23 8 4 SERVICE AND SUPPORT .............................................
Industrial PCs BPC1000 ABOUT US ads-tec GmbH Raiffeisenstr. 14 70771 Leinfelden-Echterdingen Tel: +49 (0) 711 / 45894-0 Fax: +49 (0) 711 / 45894-990 www.ads-tec.com Germany ads-tec GmbH provides large enterprises and globally active corporations with cutting edge technology, up-to-date know-how and comprehensive services in the area of automation technology, data processing technology and systems engineering.
Industrial PCs BPC1000 1 REMARKS 1.1 RELEVANT DEVICE DOCUMENTATION Consult the following documentation for information pertaining to device setup and operation: USER MANUAL ON THE SERVICE CD (THIS DOCUMENTATION): Contains information pertaining to device mounting, startup and operation as well as the technical data for the device hardware. SERVICE CD: Contains drivers, user manual and installation instructions for installing drivers. a 1.
Industrial PCs BPC1000 1.5 COPYRIGHT This User’s Guide inclusive of all the images it contains is entirely proprietary and subject to copyright. Any irregular use of this Guide by third parties infringing copyright terms is thus strictly forbidden. Reproduction, translation, as well as electronic and photographic image storage and/or amendment processes, are subject to prior written authorisation directly by M/s. ads-tec GmbH.
Industrial PCs BPC1000 1.
Industrial PCs BPC1000 1.9 SCOPE OF DELIVERY Please check that all of the following components are contained in the packaging: • 1 x device • Service CD including manual and drivers for Windows XP® • 1 x 3-pin COMBICON connector Vendor: Phoenix Contact Part designation: MC 1,5 / 3-STF-3,81-BD Note: The COMBICON connectors in the following list are only included in the scope of delivery with the equipment version including I/Os.
Industrial PCs BPC1000 2 OPERATING INSTRUCTIONS This device contains electrical voltages and extremely sensitive components. User intervention is restricted to plugging in additional cards, only. The manufacturer or a service partner authorised by the manufacturer should be consulted if you plan to make further modifications. For this type of work, the device must be switched off at the mains and the power lead must be disconnected.
Industrial PCs BPC1000 2.2 WARRANTY / REPAIRS During the unit warranty period, any repairs thereto must strictly be conducted solely by the manufacturer or by service personnel that has been duly authorised by the manufacturer. 2.
Industrial PCs BPC1000 3 INSTALLATION 3.1 12 LAYOUT FOR DEVICE INSTALLATION © ads-tec GmbH • Raiffeisenstr.
Industrial PCs BPC1000 3.2 ORDER OF INSTALLATION The BPC 1000 device may be installed by using the pre-installed wall-mount bracket. The wall-mount bracket allows installing the device on a wall or inside a switching cabinet. The BPC 1000 installation at the intended location can be carried out by using both holes at the upper and lower edge of the wall-mount bracket. Dimensions and distances may be determined in detail from the figure. © ads-tec GmbH • Raiffeisenstr.
Industrial PCs BPC1000 4 COMMISSIONING The power supply connection and interfaces of this device are installed at the device front panel. All supply leads and all required data leads have to be connected before starting commissioning. Warning: The device must be switched off before connecting or disconnecting any cables in order to prevent damage to the electronics! The device may only be switched on after acclimatising to the ambient temperature in order to avoid condensate accumulation.
Industrial PCs BPC1000 4.3 4.4 OPERATIONAL READINESS CHECK • Connect the power cable to the power source. • Check the device to determine whether damages have been caused by improper transport, incorrect operation or storage conditions or improper handling (e.g. smoke emission from the device, etc.). If damages are found, immediately shut down the device and protect it against unintentional startup. PLC SWITCH The PLC switch is located underneath the cover at the front of the device.
Industrial PCs BPC1000 5 INTERFACES 5.1 5.2 16 DIGITAL INPUT PIN NUMBER SIGNAL NAME 1 24V DC 2 GND 3 Input 1 4 Input 2 5 Input 3 6 Input 4 7 Input 5 8 Input 6 9 Input 7 10 Input 8 11 Input 9 12 Input 10 13 Input 11 14 Input 12 DIGITAL OUTPUT PIN NUMBER SIGNAL NAME 1 24V DC 2 GND 3 Output 1 4 Output 2 5 Output 3 6 Output 4 © ads-tec GmbH • Raiffeisenstr.
Industrial PCs BPC1000 5.3 24 V DC POWER SUPPLY The power supply voltage is supplied via a feed-through clamp including screw connection (figure shows socket in the device). PIN NUMBER SIGNAL NAME 1 24V DC 2 PE 3 0 VDC Technical data of the power adapter • Power consumption: Max. 60 Watts • Input voltage: 24V DC Note: The typical power consumption of this device is indicated in the "Technical details" chapter. 5.
Industrial PCs BPC1000 5.6 COM PORT The mini-DIN interface in the device is used as a COM port. 18 PIN NUMBER SIGNAL NAME 1 Data 2 NC 3 GND 4 +5V 5 Clock 6 NC © ads-tec GmbH • Raiffeisenstr.
Industrial PCs BPC1000 5.7 DVI INTERFACE The DVI Interface is used to transfer analog and digital video signals. A DVI-I Cable is required to connect a digital display to the device. It is also possible to connect a VGA display by using a suitable DVI-VGA adapter. Notice: The DVI Interface is a Single Link Interface. The video signals are transferred analog and digital.
Industrial PCs BPC1000 5.8 SWITCHING THE RESOLUTION The feature of switching the resolution allows manually changing the display resolution at the device. Stages 0-2 are the predefined default settings you can find in the table. Stages 3-7 are undefined defaults. A resolution of 800 x 600 is used for output by default. 5.
Industrial PCs BPC1000 6 SOFTWARE & DRIVER INSTALLATION The device will be delivered with a pre-installed Windows operating system on request by the customer. The drivers required for this, are already installed and the operating system will be enabled by entering the licence information. Should an initial installation be required, please follow the following steps.
Industrial PCs BPC1000 6.2 LOCK USB FUNCTION FUNCTIONAL SCOPE: The Lock USB function allows locking of USB ports. If the lock is switched on, the USB ports will be disabled by the operating system. Connected devices will not be recognised. SYSTEM REQUIREMENTS: The Lock USB function requires the Windows XP® or Windows XP embedded® operating system as a prerequisite. INSTALLATION Note: This tool and the related documentation is included on the supplied service CD. 22 © ads-tec GmbH • Raiffeisenstr.
Industrial PCs BPC1000 7 TECHNICAL DETAILS 7.1 COMPUTER DATA The device may be equipped with the following ads X modules ex factory (according to customer requirements) VERSION 1 INTEL Celeron M 800 MHz ULV 256MB - 2GB DDR RAM Intel 855 GME VERSION 2 INTEL Pentium M 1.4 GHz 2MB Cache 256MB - 2GB DDR RAM Intel 855 GME Graphic memory A max. of 32 MB shared memory Mass storage device 1 x compact flash device, 256MB-2GB under front cover, external access AS AN OPTION: 2.5" HDD incl.
Industrial PCs BPC1000 8 SERVICE AND SUPPORT ads-tec and appointed partner companies offer you comprehensive maintenance and support services, ensuring quick and competent support should you have any questions or concerns with regard to ads-tec products and equipment. ads-tec products may also be provided and installed by partner companies. Such devices may have customised configurations.
