Contents Contents 1 Foreword . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3 Description & equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 4 Placing into service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 5 Before the journey . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1 Foreword 1 Foreword You want to get to know new horizons? Count on us to help you! Congratulations on your new ADRIA Van. We have designed and built your vehicle so that travelling with your "home away from home" will be very enjoyable. 1.1 Before your first journey • Take your time and read this instruction manual on one of the comfortable seats of your vehicle.
1 Foreword 1.3 Maintenance and repair • Please contact your local ADRIA dealer for all service and repair work as well as special questions. – The employees of your authorised workshop will be pleased to provide advice and assistance. – Only original parts ensure the quality and operational readiness of your vehicle. – If service work is neglected or performed incorrectly, we will be unable to meet our warranty obligations according to our warranty conditions.
2 Safety 2 Safety 2.1 Safety instructions This Section contains safety instructions that must be followed when operating the vehicle. Important! We point out explicitly that we will not assume any liability for damage and malfunctions resulting from the nonobservance of this instruction manual. 2.1.1 Explanation of symbols Danger! Type of danger Avoidance This type of safety warning warns of an imminently pending danger that could jeopardise the life and health of persons.
Safety 2.2 General safety instructions • • • • • • • 2.3 Safely store all objects before starting to drive. Securely close all flaps, doors, windows and hatches. Keep liquids in leak-proof containers. When staying in the vehicle, always keep the forced ventilation and the mushroom ventilator open and never covered, as there is a risk of suffocation by increased carbon monoxide. Always keep the instruction manuals for the vehicle and all installed appliances (e.g.
2 Safety 2.3.1 Driving the van • • • • • • • Drive according to your abilities taking the larger dimensions and the higher weight of the vehicle into consideration. You need time for familiarisation. Always take corners in a large radius and slowly. The cornering behaviour as compared with a passenger car changes because of the length of the vehicle and its weight. At driveways and crossings, the vehicle acceleration is significantly lower than that of a passenger car.
Safety 2.
2 Safety 2.5.1 Gas stove Danger! Risk of suffocation In regular operation of the gas stove there exists acute danger to life due to lack of oxygen and the possibly generated odourless and toxic carbon monoxide (CO)! Always ensure good ventilation when the gas stove is in operation. Always keep a window, a roof hood or the doors open. Never use the gas stove for heating. Danger! Risk of poisoning 2.5.
Safety 2.5.3 2 Gas appliances in general Pay attention to the following when operating the gas system: 2.6 The regulators and the exhaust gas routing must be inspected every two years! The inspection must be confirmed on the inspection certificate according to the DVGW [German Technical and Scientific Association on Gas and Water] worksheet G 607. The operator has to initiate the inspection. The exhaust gas pipe must be fitted tightly to both the gas heater as well as the cowl and must be sealed.
2 Safety 2.6.1 Safety instructions for emergency power generator (special accessory) Observe the following when operating emergency power generators: Voltage variations during operation with an emergency power generator must be avoided to prevent damage to the electrical system and the electrical appliances. For more information, see the separate instructions from the manufacturer. Important! We recommend the installation of a voltage monitor by your dealer. 2.7 Fire prevention 2.7.
Safety 2.8 2 Safety instructions for the roof Warning! Risk of injury and of damage to the vehicle roof Do not walk on the van roof. Clear snow and ice from the roof and from the roof hoods. Use a ladder which is placed against the roof edge for this purpose. 2.9 Safety instructions for rear carrier systems (special accessories) Warning! Risk of injury and damage to the vehicle Pay attention to the statutory regulations for the installation of a rear carrier.
3 Description & equipment 3 Description & equipment 3.1 About this instruction manual In the diagrams for explanation of the equipment, "black arrows" always stand for switching off or closing an equipment part and "white arrows" for switching on or opening. 3.2 Bodywork The vans are designed as follows: • • • Outer skin: Sheet steel Insulation: X-Trem / Styrofoam Inner wall: Plywood To improve road safety, a 3rd brake light is installed in the upper rear area. 3.
Placing into service 4 Placing into service 4.1 Registering the vehicle 4 Before the first journey, the vehicle must be registered according to national regulations and a license plate fitted. Vehicles may be operated in road traffic only when insurance cover exists. An EC approval exists for the vehicle. 4.2 Placing the vehicle into service for the first time Warning! Make sure to follow the safety instructions Carefully read and follow the safety instructions (Chapter 2.
5 Before the journey 5 Before the journey 5.1 Loading the vehicle Warning! Risk of injury and severe damage to the vehicle When a tyre bursts, the vehicle can get out of control. Do not exceed the vehicle gross weight rating. Check the tyre pressure (Chapter 22.1) at regular intervals. Tyres can burst when the tyre pressure is too low. Warning! Danger of overloading The gross weight rating entered in the vehicle documents must not be exceeded.
Before the journey 5 Important! Weigh the completely loaded vehicle on public scales before starting your journey. VEHICLE LOADED INCORRECTLY! • Steerability and braking effect are reduced. 10100095 Fig. 1 Vehicle loaded incorrectly VEHICLE LOADED CORRECTLY! • Store objects between the axles, if possible. • Store heavy objects at lower positions. • Store light objects at upper positions. 10100094 Fig.
5 Before the journey 5.3 General check before starting to drive Warning! Hazards and damage due to unsecured load After having driven for a few kilometres, check the additional load is stowed in slip-free manner in the vehicle. Go through the checklists (Chapter 23) before starting to drive. 5.4 Fastening system ISOFIX for child car seats Some models have the ISOFIX fastening system for child car seats. Please select the suitable child car seat for your child according to the Table (Tab. 2).
Before the journey 5 For children from ... Weight Age (approx.) Height (approx.) Group 0 > 0 to 10 kg From birth to 1 year to 75 cm Group I > 9 to 18 kg 1 to 4.
5 Before the journey • • • Always use tyres of the same construction, same brand and same type (summer and winter tyres). Do not forget the spare wheel (see Tab. 25 in Chapte 22.1). Regularly check the wheel nuts or bolts for firm seating. When the vehicle is put out of service for a longer period, prevent "flat spots" on the tyres. – Relieve the load on the tyres by jacking up the vehicle.
During the journey 6 6 During the journey Danger! Risk of injury due to sliding passenger seat (on some models) Move the rear seat bench into its basic position and lock it in place. Caution! Risk of injury and damage to the vehicle During positioning manoeuvres, when driving through passageways, bridges, tunnels and with overhanging branches, observe the dimensions of the vehicle. Dimensions of the vehicle, see vehicle documents.
7 After the journey 7 After the journey 7.1 Requirements for the parking area The parking area should be firm and level. 7.2 Pitching the vehicle A second person is helpful for the following tasks. Aligning the vehicle: Align the vehicle horizontally in the driving direction by manoeuvring. Align the vehicle horizontally crosswise to the driving direction. – If sufficient room is available, move the vehicle until you have found a horizontal position.
Living 8 Living 8.1 Sliding door 8 Important! The door locks of the sliding doors are connected to the central locking on all vans. Warning! Risk of injury Always make sure not to injure any persons or animals, or damage any objects when opening and closing the door. Always use just the grip to open and close the door. Always open and latch the sliding door completely, especially when the vehicle is parked on a slope.
8 Living 8.1.2 Opening / closing the sliding door from the inside 1 Door lever 2 Door handle 1 2 10100116 Fig. 5 Opening / closing the sliding door from the inside Opening the sliding door: Pull the door lever (Fig. 5/1) to the rear and open the door up to the locking position. Closing the sliding door: 8.1.3 Use the door handle (Fig. 5/2) to slide the door until it latches in on its own.
8 Living 8.1.4 Flyscreen door (special equipment) Some models have an optional flyscreen door. Caution! Damage Open the flyscreen door (special equipment) fully before closing the sliding door. 1 Open the flyscreen door fully (100 %) before closing the sliding door. 2 The flyscreen door must lock in with a "click". 3 Close the sliding door. Do not close the sliding door unless the flyscreen door is fully open. 10100128 Fig.
8 Living 8.2 Ventilating the vehicle Danger! Poisoning by gas and carbon monoxide Always keep the forced ventilation (in the roof hoods and in the floor panel) and the mushroom ventilators open, do not cover them. Caution! Possibility of mould formation • • • • At night, condensation water could collect under the cushions. To dry the cushions (foamed material), place the cushions in an upright position and ventilate the vehicle thoroughly.
Living 8 Opening the window: Open the two locking levers (Fig. 7/1) on the hold-open hinges (Fig. 7/3) first. Then open the locking levers (Fig. 7/2) on the bottom edge of the window. Push the window to the outside until it has the desired opening width. Window with knurled screw: Tighten the knurled screw(s) (Fig. 7/4) clockwise when the hold-open hinge has reached the desired opening position. Closing the window: 8.3.
8 Living 8.3.3 Permanent ventilation Caution! Cracks in the window For permanent ventilation, close only the levers (Fig. 7/2) at the bottom edge of the window in the "permanent ventilation" position, otherwise the window pane is bent. This could result in the formation of cracks in the acrylic glass window. Ensure all bottom catch bars are closed in the same position, otherwise, the window could be distorted. 2 34 Fig.
Living 8.4 8 Window blinds and insect screens Caution! Damage to insect screen When you unlock the blind/insect screen, hold on to the insect screen (Fig. 10/3), otherwise it will snap up with spring tension. Snapping up could damage the screen spring and the insect screen. Only close the blind to a maximum of 75 % during direct sunlight. Air must be able to circulate. 3 1 Blind 2 Pushbuttons 5 3 Insect screen 4 Catch 5 Side catches (extra for wide blinds) 4 5 2 1 10100083 Fig.
8 Living 8.5 View protectors in the vehicle front Caution! Damage to view protector The fabric of the view protector is sensitive to pressure and can thus be easily damaged. To prevent people from looking into the interior of the vehicle, a view protector is fitted to each the windows of the driver's cab: The view protector closes off: • Windscreen • Side windows 8.5.
Living 1 Fig. 12 1 View protector (left half) 2 View protector (right half) 8 2 Windscreen view protector Bring the interior rearview mirror into a position parallel to the windscreen. Hold each view protector (Fig. 12/1, 2) by the grip (Fig. 11/2). Slide both halves of the view protector (Fig. 12/1, 2) to the middle of the windscreen. Opening the view protector: 8.5.2 Hold each half of the view protector (Fig. 12/1, 2) by the grip (Fig.
8 Living 8.5.3 Pleated side window view protectors (special equipment) 8.5.3.1 Version 1 1 Fig. 14 2 3 1 View protector 2 Grip 3 Magnetic buttons Pleated view protector side window - version 1 The pleated view protectors (Fig. 14/1) are integrated in the right and left door frames in the driver's cab. Closing the pleated view protector: Slide the grip (Fig. 14/2) in the direction of the arrow. This unlocks the pleated view protector. Unfold the view protector (Fig.
Living 8.6 Roof openings 8.6.1 General 8 Important! 8.6.2 • Before starting the journey, check the roof openings for damage to the glass dome. • Open the blind and insect screen before starting the journey. • Close the roof openings before starting the journey. • ADRIA recommends a maximum speed of 130 kph. • Do not open the roof openings by strong wind/storm, rain, hail, snowfall or outdoor temperatures under -10 °C. • Make sure the opening area above the roof hood is free.
8 Living 8.6.3 Roof hood with crank operation (special equipment) 1 Hand crank 1 Fig. 17 Opening and closing the roof hood with crank version 1 Opening the roof hood: Some models are equipped with additional locking levers (Fig. 8). Swivel the hand crank (Fig. 17/1) out. Turn the hand crank only until a resistance can be felt. The roof hood is now in the maximum open position. Any desired interim position is possible. Closing the roof hood: Turn the hand crank (Fig.
8 Living 8.6.4 Roof hood blind and insect screens running in opposite directions Important! • Both pleated blinds are continuously adjustable and can be operated together or separate from each other. • Only close the pleated blind to a maximum of 75% during direct sunlight. Air must be able to circulate. 3 Fig. 18 1 1 Inner frame 2 Pleated blind 3 Pleated insect screen 2 Roof hood blind and insect screen running in opposite directions - version 1 The pleated blind (Fig.
8 Living 8.7 Control panel Different control panels are installed in the vehicle depending on the model: Battery voltage and, depending on the model, water tank and fuel tank levels can be queried via the control panels. The control panels are located inside the vehicle. 8.7.
Living 8 Important! The indicator goes off after approx. 20 s when no button is pressed in this time. Checking the tank fill levels: The 12 V supply voltage must be switched on to display the tank fill levels. Turn the rotary setting button (Fig. 19/10) until the desired tank symbol (Fig. 19/6) or (Fig. 19/7) lights. The scale legend "%" (right) lights or blinks and the fill level of the selected tank is shown on the LED scale concerned (Fig. 19/3) or (Fig. 19/4).
8 Living 8.8 Electrical entrance step (special equipment) Some vehicles are equipped with an electrical entrance step. Warning! Accident hazard Maximum load of entrance step: 200 kg. Only use the step when it is fully extended. Before starting the journey, ensure the entrance step is completely retracted. Extend and retract the entrance step only in an unloaded condition. Keep persons and pets away from the entrance step during extension or retraction.
8 Living 8.9 Seating group / table The driver's and passenger's seats can be rotated, and the seating group can therefore be extended. 8.9.1 Rotatable driver's / passenger's seat (special equipment) Danger! Accident hazard when the driver's seat rotates while driving The driver's seat must be locked before you start to drive. 1 Seat 2 Bar (forward / backward) 3 Unlocking device (turn) 1 2 3 Fig. 21 Rotatable driver's/passenger's seat Actuate the unlocking device (Fig.
8 Living The cushions of the seat benches are attached to the substructure with snap buttons, snap-on fasteners and/or Velcro fasteners. Some models have passenger seats that slide to the side (option). 1 1 2 Fig. 22 3 1 Seat 2 Lever 3 Snap button 10100122 Sliding seat Sliding the individual seat out: Sit down on the seat. Pull side lever (Fig. 22/2) upward and push seat (Fig. 22/1) to the side. Lower the lever, check seat locking by gently jogging the seat.
Living 8.9.4 8 Tables Warning! Risk of burning and scalding Ensure the table is locked securely before serving food and hot drinks on the table. Remove all food and drinks from the table before you start converting. If the table top moves, cups or glasses could tip over or plates could fall off the table. Warning! Risk of injuries in the case of an accident Before starting a journey with the table hung in position, first fold the table foot up and stow the table away safely (e.g.
8 Living 8.9.4.2 Suspended table with swivelling table top extension 1 Fig. 24 2 1 Table top 2 Extension plate 3 Locking pin 4 Table foot 3 4 Extending the suspended table Extending the suspended table: Pull the locking pin (Fig. 24/3) on the underside of the table (Fig. 24/1). Swivel the extension plate (Fig. 24/2) in arrow direction until the latch engages. Stow away in reverse sequence. 8.9.4.3 Pedestal table 1 Table top 2 Locking lever 1 2 Fig.
Living 8.10 8 Furniture locks Caution! Damage to the handles Do not pull too hard on a handle when the respective door, flap or drawer cannot be opened. First unlock the drawers before opening them. To close the bathroom door, always hold the door handle pressed fully down. Depending on the production series, there can be different locking systems. The drawings serve only to show the operating principle. Differences in form are possible. 8.10.
8 Living 8.10.2 Furniture locks - version 2 1 Locking button 1 Fig. 27 Furniture lock - version 2 Opening: Press the locking button (Fig. 27/1), the button springs out. The lock is unlocked. Open the cabinet door, flap or drawer. Closing: Close the cabinet door, cabinet flap or drawer. Push the locking button (Fig. 27/1) in until it latches into place. The lock is locked. 8.10.3 Furniture locks - version 3 1 Locking button 1 Fig.
Living 8.11 8 TV equipment (special equipment) Caution! Damage to the vehicle Before starting the journey, you always have to lower and lock the antenna. Retract, lay it flat and secure the satellite dish before starting the journey. Lock the antenna mast into place to prevent twisting of the satellite dish. Caution! Damage to the cables Make sure the cables always have enough room to move. Caution! Damage to the appliance Check all locking grips are engaged before each journey.
8 Living 8.12 Washbasin, foldable Caution! Damage to mirror and washbasin Always lower the washbasin slowly. 1 2 1 Grip hole 2 Washbasin (folded up) 10100060 Fig. 29 Washbasin, foldable - folded up Folding the washbasin down: Grip inside the grip hole on the mirror (Fig. 29/1) and carefully pull the washbasin (Fig. 29/2) with mirror. Fold the washbasin (Fig. 29/2) with mirror down. 1 2 1 Water tap 2 Washbasin 10100059 Fig.
Sleeping arrangements 9 Sleeping arrangements 9.1 Folding bed at the rear of the vehicle 3 2 1 Folding bed 2 Retaining belt 3 Buckle latch 4 Support rail 9 1 4 Fig. 31 Bunk bed - guard against falling Lowering the folding bed: Open the retaining belt (Fig. 31/2,3). Lower the folding bed (Fig. 31/1) onto the support rail (Fig. 31/4). Securing the folding bed: 9.2 Lift the folding bed and secure it with the retaining belt (Fig. 31/2,3).
9 Sleeping arrangements 1 Lifting bed 2 2 Ceiling belt holder 3 Retaining belt 3 4 Antifall guard 5 Manoeuvring handle 6 Hook-in holes for ladder 4 1 5 Fig. 32 6 6 Lifting bed Lowering the lifting bed: Unfasten the retaining belt from the ceiling. Using both hands, push the lifting bed (Fig. 32/1) down with the manoeuvring handle (Fig. 32/5) to the stop. Hang the ladder into the hook-in holes (Fig. 32/6) on the lifting bed. Fasten the antifall guard (Fig.
9 Sleeping arrangements 9.3 Converting the seating group into a single bed in driving direction Important! The extra table top must not be swivelled out on models with such an extra table top. 1 2 3 4 1 Upholstered headrest 2 Backrest cushion 3 Table 4 Seat cushion 5 Driver's seat 5 10100127 Fig. 33 Conversion into single bed Turning the driver's seat: Rotate the driver's seat (Fig. 33/5) 180° against the driving direction (Chapter 8.9.1).
9 Sleeping arrangements 9.4 Installing the extra bed crosswise to the driving direction (special equipment) Danger! Risk of injury During the journey, the extra bed may not be installed. Safely stow away the supporting board and the extra cushion before starting the journey. 4 3 5 A 2 Passenger's seat 2 Driver's seat 3 Table 4 Seat cushion 5 Backrest cushion 6 Supporting board 7 Extra cushion B B C A A 6 7 Fig.
Sleeping arrangements 9.5 9 Converting the rear seats into single beds 4 3 6 1 5 4 Fig. 35 3 2 1 Driver's seat 2 Passenger's seat 3 Seat cushion 4 Backrest cushion 5 Supporting board 6 Extra cushion 10100118 Twin 500 S - double bed conversion Rotating driver's seat and passenger's seat: Rotate the driver's seat (Fig. 35/1) and the passenger's seat (Fig. 35/2) 180° against the driving direction (Chapter 8.9.1). Tip the seats to the front so that a horizontal seat is created.
10 10 Power supply Power supply Caution! Short-circuit, corrosion and cable break 10.1 For your own safety, have the electrical system checked at least once a year by an authorised workshop. 230 V power supply The vehicle can be connected to an external power supply with 230 V which must be protected with a 30 mA ground-fault circuit breaker (fault current). 10.1.
Power supply 10.2 10 Fuse protection of the 230 V electric circuit in the vehicle The external 230 V power supply of the vehicle is protected with a 13 A circuit breaker. In addition to the circuit breakers, a ground-fault circuit breaker (special equipment) is installed in some vehicles. The ground-fault circuit breaker protects persons against electric shock if the insulation of electrical appliances is defective.
10 10.3 Power supply Power supply - external generator (special accessory) Caution! Damage to vehicle electronics Voltage variations or voltage peaks must not occur. Make the connection from the generator to the vehicle only when the generator is in operation.and the output voltage is constant. Switch the generator off only after the connection between the vehicle and the generator has been disconnected. For more information, see the separate instructions from the manufacturer. 10.
Power supply 1 23 4 Battery-Type Battery Lead-Gel to Panel 1 on + - Lead-Acid off + - AES 1 2 5 *** 15A ! Fuse only with AES refrigerator 1 Connection for control panel 2 Connections 3 Battery selector switch 4 Battery disconnect switch 5 Mains connection 6 Connection for solar charge regulator 7 Connections 8 Vehicle flat blade fuses 3 7 4 ! Caution ! Rear side gets hot. Do not touch ! 5 6 8 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 8 Fig.
10 Power supply The option of switching over with the battery selector switch ensures optimum charging of the two battery types (lead-gel or lead-acid). • Selection of lead-gel battery: Set the battery selector switch to "Lead-Gel". • Selection of lead-acid battery: Set the battery selector switch to "Lead-Acid". Use a thin object for the changeover (e.g. ball-point pen refill). For more information, see the separate instructions from the manufacturer. 10.4.
Power supply 10 Important! 10.4.4 • Before and after each use of the vehicle, the battery should be charged with the battery charger, if possible, for more than 24 hours. • If you are on the way for a longer journey, the battery should be "fully" charged at least once a month via the 230 V mains. • If the vehicle is not used for a longer period of time, all appliances must be switched off (pay attention to hidden appliances, for example satellite system, tank heating, boiler safety valve, etc.).
10 Power supply Amperage Colour Function Installation location 2A Grey Fuse of living area battery Next to the living area battery 3A Violet Fuses of Thetford toilet In the housing frame of the Thetford cassette 20 A Yellow Fuse of refrigerator Next to or in the transformer/ rectifier 50 A Red Fuse of 12 V power supply unit Next to the living area battery Tab. 3 Fuses 1 Fig. 39 1 Intact fuse element 2 Interrupted fuse element 2 12 V fuse Changing the fuses: 10.
Power supply Electrical diagram - basic vehicle Fiat 10100155 10.6.1 10 Fig.
11 Gas system 11 Gas system 11.1 General information about the gas system Familiarise yourself with the safety instructions for handling gas. For general safety instructions concerning the topic of "gas", see the "Safety instructions for the gas system" (Chapter 2.5).
Gas system 11 Important! • The complete gas system in the vehicle is designed for an operating pressure of 30 mbar which is kept constant by the built-in pressure regulator. • The gas system must be inspected again every two years and after making any modifications and repairs. Always have a gas leak test performed on this occasion. The vehicle owner is responsible for initiating the inspection.
11 Gas system 11.3.1 Propane gas Propane is a colourless and odourless gas. Propane is capable of gasification down to -42 °C. Propane is suitable for winter camping. Propane is highly flammable, heavier than air and, in high concentrations, has a narcotising to suffocating effect. 11.3.2 Butane gas Butane occurs in two different versions (isomers): Isobutane and n-butane. Isobutane and n-butane are liquid gases that are generated when crude oil is distilled.
Gas system 11.5 11 Handling gas cylinders Danger! Risk of suffocation! Close the flap of the gas cylinder compartment tight. Regularly check the seal! Caution! Danger when handling gas cylinders Read the safety instructions on the gas cylinder! Operate gas cylinders only with the pressure regulator connected! Do not smoke in the vicinity of the gas cylinders! Any kind of open flame must be avoided! This is valid in particular when replacing gas cylinders.
11 11.6 Gas system Gas pressure regulator SecuMotion/MonoControl CS (special equipment) Danger! Risk of explosion! Rapid burning of gas. When changing gas cylinders, there is always some gas left in an "empty" gas cylinder. Smoking and open light or fire are forbidden when handling gas cylinders! Caution! Pressure regulators and flexible lines Pressure regulators and flexible lines must be replaced 10 years after manufacturing at the latest.
Gas system 11.6.1 11 Placing the SecuMotion/MonoControl CS into service Important! If not used for a longer period and with the gas cylinders closed, the SecuMotion/MonoControl CS can be switched off. 1 Fig. 41 2 3 4 5 1 Shut-off valve of operating cylinder 2 Reset knob (green) 3 High-pressure hose 4 Gas flow monitor reset knob (green) 5 Gas pressure regulator Truma-SecuMotion/MonoControl CS Placing the SecuMotion/MonoControl CS into service: Open the shut-off valve (Fig.
11 11.6.2 Gas system SecuMotion/MonoControl CS - changing gas cylinders Use the screwing tool provided for screwing the high-pressure hose on and off. The screwing tool ensures the required tightening torque and prevents damage to the screw connection caused by wrong tools. 1 1 Shut-off valve 2 High-pressure hose with adapter piece 3 Attachment strap 2 3 Fig. 42 Changing gas cylinders Changing gas cylinders: 11.6.3 Close the shut-off valve (Fig. 42/1) of the empty gas cylinder.
Gas system 11 Changing the high-pressure hose: 11.7 Close the shut-off valve (Fig. 42/1) of the gas cylinder. Unscrew the high-pressure hose from the adapter piece of the gas cylinder (Fig. 42/2) and from the regulator inlet or remove the plug-on adapters, if required. Screw a new high-pressure hose to the adapter piece of the gas cylinder (Fig. 42/2) and the regulator inlet, attach the plug-on adapter. Open the valve of the gas cylinder.
11 Gas system 3 1 Fig. 44 1 Closed 2 Open 3 Gas pipe to the gas appliance 2 Quick-action stop valves - positions Using the gas appliances: Open the respective quick-action stop valve to put the desired gas appliance into service. – Quick-action stop valve closed (Fig. 44/1): The arrows on the quick-action stop valve are positioned on the gas appliance crosswise to the direction of the gas pipe (Fig. 44/3). – Quick-action stop valve open (Fig.
Water and waste water 12 Water and waste water 12.1 Water supply 12 Warning! Health hazard Formation of bacteria and algae in the water tank. Change the water at regular intervals including the boiler contents (e.g. twice a week). After the end of every journey or after 4 weeks at the latest, the water tank must be drained, cleaned thoroughly and left open (venting). Thoroughly clean the hoses after the end of each journey. Use disinfectant for the water tank.
12 12.1.1 Water and waste water Water tank 4 5 2 1 Fig. 45 3 1 Water tank 2 Filler neck 3 Lockable cap 4 Service cover 5 Water regulation adjusting grip (special equipment, position depends on equipment) 10100070 Filling the water tank - external Filling the water tank (external): Switch the water pump off on the control panel (Chapter 8.7). Close the drain on the tank bottom. – Some models are fitted with a water regulation system (special equipment) (Fig. 46/2).
Water and waste water 12.1.2 12 Faucet Drawing of hot and cold water is performed with a single-lever faucet. Depending on the installation position, the water temperature is controlled either by raising and lowering or swivelling the lever. The switch on the faucet only works when the water supply is switched on on the control panel. 1 Fig. 47 2 1 Lever (raising/lowering) 2 Lever (swivelling) Faucet Operating the faucet: Move the lever (Fig. 47/1) upward to turn on the water pump.
12 12.2 Water and waste water Waste water The accruing waste water from the sink in the kitchen and the shower and the washbasin in the bathroom is collected centrally in the waste water tank. The drain pipe and the handle for the drain valve are located on the underside of the vehicle. 2 1 Lever valve 2 Waste water pipe 1 Fig. 48 Draining the waste water tank Emptying the waste water tank: 12.2.
Water and waste water 12.2.2 12 Waste water tank heater (special equipment) On some models, the waste water tank has an electrical heater. Caution! Damage to the tank heater Operating the tank when it is empty can damage the heater. Deactivate the tank heater when the tank has been drained. Switch on the 12 V supply. Switch the tank heater on on the control panel. If the tank heater is activated, it is automatically switched on when the temperature is below +5 °C. 12.
13 13 Heater & hot water Heater & hot water Danger! Risk of fire The person using the heating must have the heat exchanger of the Truma heating replaced at the latest after 30 years. Only the heating manufacturer or an authorized workshop can exchange the heat exchanger. Heating spare parts must always be approved as spare parts by the manufacturer. Danger! Risk of explosion Never let unignited gas flow out. Switch the heater off before filling the fuel tank, when on ferries and in garages.
Heater & hot water 13.1 Combi heaters 13.1.1 Gas heater Truma Combi and Truma Combi E (special equipment) 13 Important! • The function of Truma Combi and Truma Combi E is almost identical. For the operation of Truma Combi E, the power must first be set with the power selector switch. • When new heaters are placed into service for the first time, there is a light generation of smoke. This is normal.
13 Heater & hot water 13.1.3 Control panels 1 Rotary switch for room temperature 2 Green "Operation" indicator lamp 3 Summer operation (hot water preparation 40°C or 60°C without heating) 4 Winter operation (Heating without hot water preparation or with empty water system) 5 Winter operation (Heating with hot water preparation 60°C) 6 Rotary "Off" switch 7 Yellow "Boiler heat-up phase" indicator lamp 8 Red "Failure" indicator lamp Combi 60° 3 4 Fig.
Heater & hot water 13 Use the Back button (Fig. 51/9) to return to the previous menu or the previous display. The settings in the menus are performed analog to the settings described for Truma Combi and Truma Combi E further above. For more information, see the separate instructions from the manufacturer. 13.1.4 Summer mode Important! Mixed operation (gas and electricity) is not possible in summer mode.
13 Heater & hot water 13.1.5.2 Heating without hot water preparation: Important! 13.1.6 • When the boiler is filled, the water is automatically heated. • The water temperature is dependent on the specified heater performance and the duration of the heating for reaching the room temperature. Set the desired operating mode on the control panel (Fig. 50). Set the rotary switch to "winter mode" (heating without hot water preparation) (Fig. 50/4). Turn the rotary knob (Fig.
Heater & hot water 13.1.7 13.1.8 13 Switching the heater off Set the rotary switch to "Off" (Fig. 50/6). The fan can continue to run after switching off in order to utilise the residual heat. The green indicator lamp flashes. Close the "heater" quick-action stop valve 11.7 (Fig. 43/1) when the heater is not used for an extended period of time. Close the gas cylinder shut-off valve 11.6 when no other gas appliance is in operation.
13 Heater & hot water Closing the drain valve: Check if the rotary switch (Fig. 53/2) is set to "Operation" (parallel to the water connection (Fig. 53/3)) and is engaged. It can be manually closed with the snap button (Fig. 53/5) (pressed) and then the boiler filled only when the temperature at the drain valve is above approx. 7°C. Set the heater to summer or winter mode (Chapter 13.1.4 or 13.1.5) and set the rotary switch (Fig. 53/2) of the valve (Fig. 53/1) to "Operation".
Heater & hot water 13 13.1.11 Draining the water heater Interrupt the power supply for the water pump. Open the hot water taps in the kitchen and the bathroom. Place a bucket underneath the outlet. Turn the rotary switch of the drain valve 90° until it engages (Fig. 53/2). The water heater is now drained to the outside. 13.2 Check the complete volume has been drained.
13 Heater & hot water Using the electrical floor temperature control system: 80 GB Check the circuit protection for the 230 V power supply at the camping site is adequate. (350 W - 1.5 A) Check the connection cable is wound off fully from the cable reel. Check the 230 V circuit breaker in the vehicle is switched on. Check the mains plug (Fig. 54/2) of the floor temperature control system is correctly plugged in. Check the mains plug (Fig.
Cooking 14 14 Cooking Danger! Risk of poisoning due to carbon monoxide (CO) and lack of oxygen Always open a window or roof hood when the gas stove is switched on. Never cover the forced ventilation in the roof hoods and in the entrance as well as the mushroom ventilators. Danger! Risk of explosion 14.
14 Cooking Observe the following for the glass cover (special equipment): Do not apply pressure on the glass gas stove cover when closed. Do not close the glass cover while burners are still in operation or emit heat. Do not place hot cooking pans on the glass cover. In the case of frost, keep the kitchen window closed and provide ventilation in a different way. Otherwise, the temperature difference on the glass cover could cause damage. 4 Fig.
Refrigerator & freezer compartment 15 15 Refrigerator & freezer compartment Depending on the vehicle equipment, one of the refrigerators described below is installed in your vehicle. The refrigerator and the freezer compartment form a mechanical unit. To ensure optimum function, the appliance should stand level, if possible. However, it is also suitable for inclined positions to a certain degree. Clean the refrigerator before placing it into service (Chapter 19.2.5).
15 Dometic 4 series 1 3 2 15.1.2 Refrigerator & freezer compartment 4 0 5 7 6 1 Fig. 57 2 3 4 5 Refrigerator controls (Electrolux) 1 12 V rocker switch 2 230 V rocker switch 3 Temperature selection switch 230 V mode 4 Temperature selection switch gas mode 5 Ignition switch For more information, see the separate instructions from the manufacturer. 15.1.3 Dometic 8 series with manual mode selection and automatic ignition MES 1 Fig.
Refrigerator & freezer compartment 15.1.4 Dometic 8 series with manual mode selection and battery ignition 1 2 3 Fig. 59 15.1.5 15 4 5 6 7 10100032 Refrigerator controls (Dometic 8 series) 1 Power selector switch "Off" 2 Power selector switch "Gas mode" 3 Power selector switch "12 V" 4 Power selector switch "230 V" 5 Temperature controller 6 Battery ignition (gas mode) 7 Flame display (gas mode) Thetford series N 3000 2 1 Fig.
15 Refrigerator & freezer compartment 15.2 Placing into service 15.2.1 12 V mode The 12 V mode should be selected only while the engine is running. Important! A low voltage monitor is fitted on compressor refrigerators running with 12 V. The low voltage monitor automatically switches the refrigerator off when the battery voltage drops below 11 V. 15.2.2 230 V mode Select the 230 V mode only when an external 230 V supply is connected.
Refrigerator & freezer compartment 15.2.4 15 Winter operation Important! Attach the winter covers also when the vehicle is taken out of service for an extended period of time or cleaned on the outside. Check in winter operation: Check regularly that the ventilation grilles have not been blocked by snow, ice, leaves or similar. When the outside temperature drops below +8 °C, the winter covers (special accessory) should be fitted to the ventilation grilles.
16 16 Toilet Toilet Caution! Damage to the environment Use an environment-friendly and biodegradable chemical toilet additive for the toilet. – The ventilation will remove merely the odour but not germs and gases. Germs and gases can have a detrimental effect on the rubber seals. Caution! Material breakage Do not sit on the toilet lid. – The lid is not designed to bear the weight of a person and could break. Important! • Never add toilet fluid through the valve blade or the toilet bowl.
Toilet 16.1 16 Thetford Cassette C-200 S and C-260 S Caution! Damage to the water pump during winter operation In winter operation, the toilet may be flushed only after the toilet compartment has been well heated, otherwise the water pump of the flush system could be damaged. Do not use antifreeze. 2 3 4 4 3 5 1 Fig.
16 16.2 Toilet Thetford Cassette C-200 CW/CWE (pump toilet) The Thetford Cassette C-200 CW/CWE has a separate water tank. The filler neck of the water tank is at the outside of the vehicle or at the rear of the water tank. 2 4 1 Lever for opening the valve blade 2 Flush handle 3 Fresh water tank 4 Water tank filler neck 3 1 10100121 Fig. 62 Thetford Cassette C-200 CW Filling the water tank: Open the filler neck (Fig. 62/4) with a key.
Toilet 16.3 16 Cassette Caution! Danger for the environment 16.3.1 Use an environment-friendly and biodegradable chemical toilet additive for the toilet. The cassette may be emptied only at camping sites with suitable waste water treatment plants or special waste disposal stations (e.g. at parking sites for camping vehicles). Thetford Cassette C-200 S 8 2 3 9 Fig.
16 16.3.2 Toilet Thetford Cassette C-260 S 2 3 4 Fig. 64 5 7 1 8 1 Cassette 2 Swivelling emptying spout 3 Automatic holding tank vent valve 4 Pull-out hand grip / latch 5 Sliding cover 6 Valve blade 7 Vent plunger 8 Removable mechanism 6 Thetford Cassette C-260 S The cassette (Fig. 64/1) has a capacity of 18 l and should be emptied when the level indicator (Fig. 61/4) lights. Do not allow the cassette to become overfilled. 16.3.
Toilet 16 Then pour toilet fluid into the cassette. The cap of the emptying spout has a measuring cup on the inside. This decomposes the faeces quickly, prevents unpleasant smells in the cassette and keeps the inside of the tank clean. Fit the tank back in again. Close the access door. For more information, see the separate instructions from the manufacturer. 16.
17 Winter camping 17 Winter camping 17.1 Travelling in winter Winter camping is becoming more and more popular. Your ADRIA vehicle is suitable, to the greatest possible extent, for use in winter and if you pay attention to the following information, your winter holiday in your own vehicle will become proper winter fun. Important! Before starting the journey, mount suitable winter tyres and have snow chains on board. Snow chains are prohibited on aluminium rims.
Winter camping 17.2 17 Winter operation Danger! Risk of suffocation Do not use any catalytic stoves or infrared radiators in the vehicle. The oxygen in the living area is then used. Caution! Risk of damage through freezing Do not store any fluids in the unheated vehicle when there is a risk of frost. If the vehicle is left with the heating switched off for a longer period of time at low temperatures, the water pipes and tanks could freeze and thus be damaged.
17 17.3 Winter camping Open windows and roof hoods when cooking. If possible, do not use electrical appliances with high current consumption. The current capacity at camping sites is limited. Make sure the drain pipe of the waste water does not freeze up (Chapter 12.3).
Placing out of service 18 18 Placing out of service Important! When the instructions for maintenance and care, and the checklist for placing out of service are observed, the vehicle can be parked outdoors all year round. 18.1 Checklist for temporary placing out of service: Activity Bodywork Keep the forced ventilation and all mushroom ventilators open. Carefully wash the vehicle and apply a paint protection product (wax). Repair paintwork damage.
18 Placing out of service Activity Water system Empty the entire water system completely, clean carefully and allow to dry. Leave all water taps, all drain cocks as well as all drain valves open. Drain the faucets that have a "warm" and a "cold" position in both positions and leave them open in one of the positions. Bacteria and algae can form in the water tank, therefore, after the end of the journey, the water tank must always be drained, thoroughly cleaned (Chapter 12.3) and allowed to dry.
Placing out of service 18.2 18 Placing out of service over the winter The following measures are required in addition to those already mentioned for the temporary placing out of service over the winter. Activity Bodywork Clear snow from the roof when it snows. Thoroughly heat and ventilate the vehicle every four weeks. Lubricate all hinges and locks. Apply talc or Vaseline to all rubber seals. Use graphite dust to treat locking cylinders.
18 18.3 Placing out of service Returning to service after the placing out of service Perform the following activities for placing into service again: Activity Bodywork Remove tarpaulin and possibly wooden slats. If the vehicle has been stationary for a long period (approx. 10 months), have the brake system checked by an authorised workshop. Check the tyre pressure, also of the spare wheel (special equipment). Remove cover from the exhaust cowl, if present.
Cleaning & care 19 Cleaning & care 19.1 Cleaning and care - exterior 19 We recommend the following steps for the care of the vehicle: Warning! Risk of injury and of damage to the vehicle roof Do not walk on the van roof. Clear snow and ice from the roof and from the roof hoods. Use a ladder which is placed against the roof edge for this purpose. Important! • Never drive the vehicle through a wash facility. The acrylic glass windows will be scratched by the rotating cleaning brushes.
19 19.1.1 Cleaning & care The painted outer surface of the vehicle can be preserved with a commercially available wax. Pay attention to the manufacturer's instructions. Treat polyester parts every year with a two-component wax. Pay attention to the manufacturer's instructions. Observe the environmental protection measures in cleaning and care of the vehicle. Cleaning the acrylic windows (side windows, roof hoods) Important! • Never drive the vehicle through a wash facility.
Cleaning & care 19.1.2 19.2 19 Cleaning plastic parts Clean plastic parts only with warm water, mild household cleanser and a soft, clean sponge or cloth. The aqueous solution should contain 2 % cleaning agent at the most. Do not use scouring agents. They would scratch the plastic surfaces. Very greasy or oily spots can be washed with ethyl, isopropyl or isobutyl alcohol. Organic solvents (e.g. acetone, methanol or ethanol) could damage the material.
19 Cleaning & care 19.2.2 Care of furniture 19.2.3 19.2.4 Clean the furniture with a soft cloth and a commercially available furniture polish, do not use intensive cleansers. Wash the work surfaces with water by adding a mild detergent or household cleanser. Clean textile storage spaces and textile cabinets with cleansing foam.
Cleaning & care 19.2.5 19 Cleaning the kitchen 19.2.5.1 Cleaning work surfaces and sink Wash the work surfaces with water to which a mild detergent or household cleanser has been added and dry the surfaces. Clean the stainless steel sink with a commercially available cleanser. 19.2.5.2 Cleaning the gas stove Caution! Damage to gas stove Prevent water or cleaning agent from penetrating the gas outlet openings. Water may damage the gas stove. Do not use scouring agents.
19 19.2.6 Cleaning & care Cleaning the bathroom Caution! Damage to surfaces Do not clean the bathroom and the toilet with solvents or cleaning agent containing alcohol. Do not use scouring agents. – These could cause cracks or embrittlement of the plastic material. Do not pour caustic substances or boiling water into the drains. – These damage both the drain pipes and the siphon traps. Do not allow the door seal to come into contact with oil or grease. Do not use scouring agents.
Inspection & maintenance 20 Inspection & maintenance 20.1 Inspection work 20 Important! A leisure vehicle must be officially inspected at regular intervals just like other vehicles. Important! Use only original spare parts from the respective manufacturer. 20.2 Inspection and maintenance work must be performed at regular intervals. Since special technical knowledge is required for the performance of the maintenance and inspection work, it has to be performed by authorised workshops.
20 20.
Troubleshooting 21 21 Troubleshooting Please pay attention to the following information for finding and correcting faults. If you cannot remedy the faults yourself, contact the Customer Service of your competent ADRIA dealer or the respective appliance manufacturer (heater = Truma, toilet = Thetford, etc.). Warning! Risk of injury and severe damage to the vehicle All repairs on the vehicle and on the brake system have to be performed in an authorised workshop only! 21.1 Changing wheels 21.1.
21 Troubleshooting Before repair: Do not pull out any foreign objects (screws or nails) that have penetrated the tyre. Before repair, carefully check the tyre sidewall. Do not use the tyre mobility system when the tyre has already been damaged by driving with the flat tyre. Also check the rim. When the rim is damaged (deformation of the bead of the rim that causes loss of air), repair is not possible. After repair: Stop after driving for approx. 10 minutes and check the tyre pressure.
Troubleshooting 1 Vehicle jack 2 Hydraulic trolley jack (special accessory) 21 2 1 Fig. 65 10100125 Jacking up with the vehicle jack The vehicle jack and the onboard tool set are under a seat in the driver's cab or in the garage. Position the vehicle jack (Fig. 65/1) or the hydraulic trolley jack (special accessory) (Fig. 65/2) only at the lifting points provided underneath the car body. For more information concerning the vehicle jack, see the separate manufacturer's operating instructions.
21 21.1.4 Troubleshooting Secure the vehicle (Chapter 21.1.1). Shut off the engine and apply the parking brake. Engage the first gear or reverse gear. Place the wheel chocks before and behind the opposite wheel. This secures the vehicle from rolling away. Get the spare wheel and the tools. Remove the protective caps from the wheel nuts or the wheel cover. Unscrew the wheel nuts or wheel bolts by half a revolution with the wheel spanner.
Troubleshooting 21.2 21 Replacing lighting elements Caution! Damage to lighting elements 21.2.1 Never touch lighting elements with your bare fingers. Always use a clean and lint-free cloth. Before starting to drive, check the function of all interior and exterior lighting equipment on the vehicle and replace defective lighting elements. Have a clean mat available for changing the lighting elements. This ensures that you will not loose any small parts. Exterior lighting 1 2 4 Fig.
21 Troubleshooting 21.2.1.1 Replacing lighting elements - front Vehicle with driver's cab of basic vehicle: Lighting - front Lighting elements Low beam bulb H7 - 55 W High beam bulb H1 - 55 W Parking light, front W5W Turn indicator, front P21W Tab. 12 Front lighting elements For more information, see the separate instructions from the basic vehicle manufacturer. 21.2.1.
Troubleshooting 21.2.2 21 Interior lighting 1 3 2 1 Lighting element with plug cap 2 Lighting element with bayonet cap 3 Cylindrical lighting element G9 4 LED insert G4 4 10100077 Fig. 68 Lighting element types, interior lighting Replace the various lighting elements as follows: 1 2 Lighting element type Replacing Lighting elements • Removing: Pull the lighting element out. with plug cap • Fitting: Push the lighting element in the socket with light pressure.
21 Troubleshooting Lighting - interior Lighting elements Ceiling light, living area LED-12 V-G4 1.0 W Ceiling light, sleeping area LED-12 V-G4 1.0 W Lighting, roof hood Halogen 12 V-G4 10 W Reading lamp, living area LED-12 V-G4 0.5 W Reading lamp, sleeping area LED-12 V-G4 1.0 W Kitchen light LED-12 V-G4 0.5 W Lighting, bathroom unit LED-12 V-G4 0.5 W Lighting, wardrobe C10W 12 V 10 W Lighting, storage space Halogen 12 V-G4 10 W Tab. 16 21.
Troubleshooting 21.4 Gas system faults Fault Possible cause Measure Gas smell, Gas system leaks. • Immediately put the gas system out of service. • Close the gas cylinder shut-off valves. • Avoid any type of ignition spark and open light. • Ventilate the vehicle well (Chapter 2.5). • Repair by authorised workshop. Gas cylinder is empty. • Exchange gas cylinder (Chapter 11.5 and 11.6). Gas cylinder shut-off valve closed. • Open gas cylinder shut-off valve (Chapter 11.6.1).
21 21.5 Troubleshooting Refrigerator/freezer compartment faults Fault Possible cause No gas operation See Chapter 21.4 "No gas". No 230 V operation No 12 V operation Cooling function is not sufficient Tab. 19 118 GB Remedy Energy selector switch on refrigerator in false position. • Switch power selector switch on refrigerator to "Gas mode" or "Automatic mode" (Chapter 15.1.2). Air in gas pipe. • Switch the appliance off and start again. Repeat three to four times.
Troubleshooting 21.6 21 Truma Combi heater faults Important! Consult an authorised workshop if the listed measures are not successful. Fault Possible cause Remedy LEDs do not light. No supply voltage. • Check battery voltage (12 V). • Check all electric connectors and fuses. Green LED lights but heater does not operate. The temperature setting on the control panel is lower than the room temperature. • Set the temperature on the control panel higher. Green LED lights and red LED blinks.
21 Troubleshooting 21.7 Power supply faults Fault Possible cause Remedy Ground-fault circuit breaker triggered Fault in 230 V cables of vehicle. • Contact Customer Service. Fault in an electrical appliance. • Disconnect all electrical consumers until the ground-fault circuit breaker no longer triggers. • Have defective appliances repaired by a qualified electrician. • Switch on the circuit breaker in the vehicle. • Switch the ground-fault circuit breaker in the vehicle on.
Troubleshooting Fault Possible cause Remedy Refrigerator does not operate in drive operation No voltage applied to refrigerator. • Have the fuse and cables checked. Transformer/rectifier defective. • Contact Customer Service. Refrigerator defective. • Have the refrigerator checked. The 12 V main switch for the living area battery is switched off. • Switch 12 V main switch for living area battery on (Chapter 8.7). Fuse or cables defective. • Have the fuse and cables checked.
21 21.8 Troubleshooting Control panel faults Fault Possible cause 12 V supply does not function 12 V main switch switched off. • Switch 12 V main switch for living area battery on (Chapter 8.7). Fuse defective. • Contact Customer Service. 12 V control indicator (green) is not lit 12 V supply switched off. • Switch on the 12 V supply. System cannot be switched on Living area battery is not charged or insufficiently charged. • Charge the living area battery. Fuse defective.
Troubleshooting 21.10 Toilet faults Fault Possible cause Remedy Toilet does not have flushing water Water tank is empty. • Fill the water tank. The pump runs, the Clogging in toilet bowl. toilet bowl is not emptied • Fill the toilet bowl with water. Allow clogging to soak for approx. 2 minutes and then flush several times in quick succession. Toilet does not function • Replace the fuse. Tab. 24 Adria Vans 21 Fuse defective.
22 22 Technical Data Technical Data Important! 22.1 • For the technical data, the statements in the registration certificate part I are binding. • Modifications of the original equipment of the vehicle ex factory can affect road safety and driving behaviour. • Accessories not approved by ADRIA for installation, attachment or conversion can cause damage to the vehicle and affect driving behaviour.
Technical Data 22.2 22 Additional load / weight Caution! Danger of overloading The driving behaviour of an overloaded vehicle changes drastically. It can get out of control during the journey. When the vehicle is overloaded, the insurance coverage and the warranty claim to the manufacturer become void. Do not exceed the gross weight rating entered in the vehicle documents. Important! 22.2.1 • Load the vehicle properly (Chapter 5.1). • Weigh the vehicle before starting the journey (e.g.
22 Technical Data 22.2.1.3 Additional load The additional load consists of: Additional equipment All objects offered in addition to the standard equipment. An extract of the weight of additional equipment can be found in Chapter 22.2.2, e.g.
Technical Data 22.2.2 22 Weight of additional equipment and accessories The following list includes additional equipment packages and accessories. The values are valid when not already included in the standard equipment of the vehicle. All weight information is "approximate information".
22 Technical Data Additional equipment / accessories Awning 20-30 kg Metallic paint finish 2 kg Metallic paint finish, front bumpers 2 kg MP3-CD-Radio with MFL and Bluetooth 5 kg Navigation system 2-5 kg Fog lamp 4 kg Upholstery, partly leather 5 kg Radio pre-installation, driver's cab 2 kg Reversing camera 2 kg Seat base cover, driver's cab 1 kg Stop & Start automatic 1 kg Daytime lights 2 kg Cruise control 1 kg Carpet, driver's cab + dinette 4 kg TFT TV-holder TV + SAT equipm
Technical Data 22.2.3 22 Weight of personal equipment and accessories Personal equipment / accessories Weight (approx.) Overall weight of personal equipment Tab.
23 23 Checklists Checklists Important! These lists also include special equipment, special accessories and personal equipment not included in the standard vehicle equipment. 23.1 Checklist, general Van checklist Van general inspection and gas inspection carried out (Chapter 2.4.1) Gas inspection carried out (Chapter 2.4.
Checklists 23 Van checklist Cassette emptied and with fresh disinfectant Additive for cassette available Gas cylinders, filled Gas cylinders secured safely in gas cylinder compartment (Chapter 11.2), screw caps and protective covers available for all cylinders Quick-action stop valves for cooker, oven etc. closed (Chapter 11.
23 Checklists Van checklist Entrance step retracted All outer doors and outer flaps securely latched and locked Child car seats attached securely Headlamp height adjustment adapted Rearview mirrors correctly adjusted Cab seats set to the right position and locked into position Rear passenger seats set to the right position and locked into position Driver's cab blinds fully open and locked Tab.
Checklists 23.
23 23.
Checklists 23.
23 23.
Checklists 23.6 23 Personal checklist Please copy and complete. Route: Date: Personal checklist Tab.
Index Index 0-9 12 V charging system . . . . . . . . . . . . . . . 12 V mode, refrigerator . . . . . . . . . . . . . . 230 V mode, refrigerator . . . . . . . . . . . . . 230 V power supply . . . . . . . . . . . . . . . . 34 86 86 50 A Accessories Weights . . . . . . . . . . . . . . . . . . . . . . 127 Additional air suspension (special equipment) . . . . . . . . . . . . . . . . 17 Additional equipment Weights . . . . . . . . . . . . . . . . . . . . . . 127 Additional load . . . . . . . . . . . . . . . . .
Index F K Faucet . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 Fire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Fire prevention . . . . . . . . . . . . . . . . . . . . . 10 Flat blade fuses . . . . . . . . . . . . . . . . . . . . 53 Floor heating . . . . . . . . . . . . . . . . . . . . . . 79 Food, storing . . . . . . . . . . . . . . . . . . . . . . 87 FrostControl . . . . . . . . . . . . . . . . . . . . . . . 77 Furniture Care . . . . . . . . . . . . . . . . . . . . . . . .
Index Registration of vehicle . . . . . . . . . . . . . . . 13 Roof hood . . . . . . . . . . . . . . . . . . . . . . . . . 31 Blind/insect screen running in opposite directions . . . . . . . 33 Care . . . . . . . . . . . . . . . . . . . . . . . . . 102 Roof openings . . . . . . . . . . . . . . . . . . . . . 31 S Safety instructions . . . . . . . . . . . . . . . . . . . 4 Screen, roof hood Running in opposite directions . . . . . . 33 Seating group . . . . . . . . . . . . . . . . . . . . . .
Notes Adria Vans GB 141
Notes 142 GB Adria Vans
Angelestraße 56 - D-88214 Ravensburg info@tef.de - www.tef.
