Contents Contents 1 Foreword . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3 Description & equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 4 Placing into service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 5 Before the journey . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1 Foreword 1 Foreword You want to get to know new horizons? Count on us to help you! Congratulations on your new ADRIA Caravan. We have designed and built your caravan so that travelling with your "home away from home" will be very enjoyable. 1.1 Before your first journey • Take your time and read this instruction manual on one of the comfortable seats of your caravan.
1 Foreword 1.3 Warranty registration In addition to these operating instructions, you will also find a Service and Warranty Booklet in your Adria caravan. Please perform the warranty registration as specified in the Service and Warranty Booklet. 1.4 Warranty, service and repair • Please contact your local ADRIA dealer for all service and repair work as well as special questions. – The employees of your authorised workshop will be pleased to provide advice and assistance.
2 Safety 2 Safety 2.1 Safety instructions This Section contains safety instructions that must be followed when operating the vehicle. Important! We point out explicitly that we will not assume any liability for damage and malfunctions resulting from the nonobservance of this instruction manual. 2.1.1 Explanation of symbols Danger! Type of danger Avoidance This type of safety warning warns of an imminently pending danger that could jeopardise the life and health of persons.
Safety 2.2 General safety instructions • • • • • • • 2.3 Safely store all objects before starting to drive. Securely close all flaps, doors, windows and hatches. Keep liquids in leak-proof containers. When staying in the vehicle, always keep the forced ventilation and the mushroom ventilator open and never covered, as there is a risk of suffocation by increased carbon monoxide. Always keep the instruction manuals for the vehicle and all installed appliances (e.g.
2 Safety 2.3.1 Driving with the caravan • • • • • • • Drive according to your abilities taking the larger dimensions and the higher weight of the vehicle combination into consideration. You need time for familiarisation. Always take corners in a large radius and slowly. The cornering behaviour as compared with a passenger car changes because of the length of the car/caravan combination and its weight.
Safety 2.
2 Safety 2.5.1 Gas stove Danger! Risk of suffocation In regular operation of the gas stove there exists acute danger to life due to lack of oxygen and the possibly generated odourless and toxic carbon monoxide (CO)! Always ensure good ventilation when the gas stove is in operation. Always keep a window, a roof hood or the doors open. Never use the gas stove for heating.
Safety 2 The exhaust gas pipe must be fitted tightly to the gas heater and to the cowl, and must be sealed. It may not show any evidence of damage. The exhaust gas routing of the gas heater must be installed ascending over its complete length and fitted tightly with clamps. If required, install exhaust gas pipe supports. Before placing the gas heater into service, always clear dirt and snow from the cowl and combustion air inlets.
2 Safety 2.7 Fire prevention 2.7.1 General fire prevention Danger! Fire risk Only authorised and qualified personnel may perform service work and modifications to the gas system and the electrical system. Never leave children in the vehicle unattended. Do not use portable heating or cooking appliances. Keep flammable materials clear of cooking and heating appliances. Acquaint yourself with the position and operation of the emergency exits in the vehicle. Always keep escape routes clear.
Safety 2.8 2 Safety instructions for the roof Warning! Risk of injury and damage to the vehicle roof The roof of the vehicle is not designed for the weight of standing persons. The roof of the vehicle is not capable of supporting walking persons. Clear snow and ice from the roof and from the roof hoods. Use a ladder which is placed against the roof edge for this purpose. 2.
3 Description & equipment 3 Description & equipment 3.1 About this instruction manual In the diagrams for explanation of the equipment, "black arrows" always stand for switching off or closing an equipment part and "white arrows" for switching on or opening. 3.2 Bodywork The bodywork of the vehicle is made in "sandwich construction".
Description & equipment 3.8 3 Water and waste water The vehicle is equipped with a water tank, and possibly as special equipment, with a waste water tank (Chapter 12).
4 Placing into service 4 Placing into service 4.1 Registering the vehicle Before the first journey, the vehicle must be registered according to national regulations and a license plate fitted. Vehicles may be operated in road traffic only when insurance cover exists. An EC approval exists for the vehicle. 4.2 Placing the vehicle into service for the first time Warning! Make sure to follow the safety instructions Carefully read and follow the safety instructions (Chapter 2.
5 Before the journey 5 Before the journey 5.1 Wheel arch insert Warning! Danger of injuries from parts flying around Remove the wheel arch inserts before driving with the caravan and stow them away safely. 5.2 Coupling the caravan Warning! Risk of injury when coupling and manoeuvring Make sure nobody is between the towing vehicle and caravan when manoeuvring and coupling. Caution! Risk of damage to the coupling Do not couple or uncouple the caravan with the overrun device shaft pressed in.
5 Before the journey Check that all corner steadies have been fully raised. Check the caravan lights when the towing vehicle is coupled. 5.2.1 Couplings Warning! Risk of weaving Before coupling, make sure the tow ball on the towing vehicle is free from oil and grease. Clean off any dirt before coupling. 5.2.1.1 Couplings AK 150 V/160/200 V/251 S/300 2 1 Safety marking 2 Coupling grip 1 10100016 Fig.
Before the journey 5.2.1.2 5 Coupling AKS 1300 2 1 3 5 1 "Locked" marking 2 Coupling grip 3 Stabilizer lever 4 Safety marking 5 Handwheel 4 3 10100017 Fig. 2 Coupling AKS 1300 Coupling the vehicle: Move the stabilizer lever (Fig. 2/3) fitted at the side up to the top position. Turn the handwheel (Fig. 2/5) anticlockwise to the stop and open completely. Pull the coupling grip (Fig. 2/2) straight up. Position the open coupling onto the tow ball until the coupling grip locks in with a click.
5 Before the journey 5.2.1.3 Coupling AKS 3004 2 1 Safety marking 2 Stabilizer lever 3 Coupling grip 3 1 10100111 Fig. 3 Coupling AKS 3004 Coupling the vehicle: Move the stabilizer lever up (Fig. 3/2) to the top position. Pull the coupling grip (Fig. 3/3) upwards and open the coupling. Position the open coupling onto the tow ball until the coupling grip locks in with a click. The coupling grip moves back to the start position on its own. To help, press the coupling grip (Fig.
Before the journey 5.2.2 5 Coupling BPW WS 3000 D 3 2 1 Stabilizer lever 2 Uncoupling position 3 Coupling position 4 Stabilizer device active 4 1 10100112 Fig. 4 Coupling BPW WS 3000 D Coupling the vehicle: Move the stabilizer lever (Fig. 4/1) to the uncoupling position (Fig. 4/2). Position the open coupling onto the tow ball and, if necessary, press down by hand until the coupling grip locks in with a click. The stabilizer handle moves approx. 10° down to the coupling position (Fig. 4/3).
5 Before the journey Stretch the overrun device, drive the towing vehicle slightly away when necessary, until the folding bellow over the overrun device is no longer pressed together. Release the coupling with the hand grip. Use the jockey wheel to lift the coupling from the tow ball until the ball is completely free. Drive the towing vehicle away. 5.4 Loading the vehicle Warning! Risk of injury and severe damage to the vehicle When a tyre bursts, the vehicle can get out of control.
Before the journey • • 5 Always keep liquids in leak-proof containers in low-lying storage compartments. Load the bike rack (special accessory) with only 2 bikes at the most (50 kg maximum). Important! Weigh the completely loaded vehicle on public scales before starting your journey. CARAVAN LOAD SPREAD INCORRECT! • Caravan weaves dangerously 10100015 Fig. 5 Caravan load spread incorrect CARAVAN LOAD SPREAD CORRECT! 10100021 Fig.
5 Before the journey 5.5 Additional rear view mirrors Warning! Accident hazard Never reverse without adequate field of view towards the rear. Use additional rear view mirrors! Check additional rear view mirrors are set correctly before driving. Important! Additional rear view mirrors must meet EU Directives and must be EU type-tested. Two rear view mirrors must be fitted on towing vehicles when towing.
Before the journey • 5 Drive over kerbs slowly and, if possible, at an obtuse angle. Avoid driving over steep and sharp-edged kerbs. – Hard or acute-angled impacts against kerbs or sharp-edged objects, for example stones, can damage the tyres. • • • Drive over high manhole covers at a slow speed. Hidden tyre damage is not eliminated by correcting the tyre pressure. Do not use used tyres. – Tyres age even when they are not driven or driven only a little.
6 During the journey 6 During the journey Caution! Risk of injury and damage to the vehicle During positioning manoeuvres, when driving through passageways, bridges, tunnels and with overhanging branches, observe the dimensions of the vehicle. Dimensions of the vehicle, see vehicle documents. Equipment and attachments change the weight and the dimensions. From a technical point of view, ADRIA caravans are designed for a permissible maximum speed of 100 kph.
7 After the journey 7 After the journey 7.1 Requirements to the parking area The parking area should be firm and level. 7.2 Pitching the caravan A second person is helpful for the following tasks. Aligning the vehicle: Align the caravan horizontally crosswise to the driving direction. If this is not possible, use drive-on chocks underneath the respective wheels or, if sufficient room is available, move the caravan until you have found a horizontal position.
7 After the journey 1 1 Crank 2 Corner steady 3 Base 2 3 10100009 Fig. 7 Corner steady Extending the corner steady: Place the crank (Fig. 7/1) against the corner steady (Fig. 7/2). Turn the crank anticlockwise to extend the corner steady. Important! • 7.2.2 Place a firm substructure (Fig. 7/3) underneath the base (Fig. 7/2) of the corner steadies when your vehicle is standing on soft ground such as grass or sand.
After the journey 7.3 7 Electrical entrance step (special equipment) Some vehicles are equipped with an electrical entrance step. Warning! Accident hazard Maximum load of entrance step: 200 kg. Only use the step when it is fully extended. Before starting the journey, ensure the entrance step is completely retracted. Extend and retract the entrance step only in an unloaded condition. Keep persons and pets away from the entrance step during extension or retraction.
7 After the journey 7.4 Waste water tank, mobile (special equipment) 2 1 Fig. 9 1 Waste water tank 2 Drain pipe 10100014 Waste water tank, mobile Store the waste water tank (Fig. 9/1) in the gas cylinder compartment of the caravan during the journey. The drain pipe (Fig. 9/2) is located on the vehicle underside on the left in driving direction. Observe the following before using the water system: Open the cap of the waste water tank and stow away safely. Place the waste water tank (Fig.
Living in the caravan 8 Living in the caravan 8.1 Entrance door 8.1.1 Opening / closing the door from the outside 1 Door lock 2 Door handle 8 1 2 Fig. 10 Opening / closing the entrance door from the outside Opening the door: Insert the key into the door lock (Fig. 10/1) and turn towards the "open lock" symbol to the stop. When released, the key returns to the initial position. Remove the key. Pull the door handle (Fig. 10/2) to open the door.
8 Living in the caravan Remove the key. Pull the door handle (Fig. 11/2) to open the door. Closing the door: Close the door until the door lock latches. Insert the key into the door lock (Fig. 11/1). Turn the key anticlockwise to the stop. If necessary, push the door lightly into the seals. When released, the key returns to the initial position. Remove the key. 8.1.2 Opening / closing the door from the inside 3 1 Door handle 2 Door opener 3 Locking button 1 2 Fig.
8 Living in the caravan 2 1 Door handle (door unlocked) 2 Door handle (door locked) 3 Locking latch 1 3 4 10100038 Fig. 13 Opening / closing the entrance door from the inside Opening / closing the door: Push the door handle (Fig. 13/1) down and open the door. When released, the door handle (Fig. 13/1) returns to its initial position. To close the door, pull the door handle (Fig. 13/1). Locking the door: Pull the door handle (Fig. 13/1) upwards into locking position (Fig. 13/2).
8 Living in the caravan 8.2 Ventilation of caravan Danger! Poisoning by gas and carbon monoxide Always keep the forced ventilation (in the roof hoods and in the floor panel) and the mushroom ventilators open, do not cover them. Caution! Possibility of mould formation At night, condensation water could collect under the cushions. To dry the cushions (foamed material), place the cushions in an upright position and ventilate the vehicle thoroughly.
Living in the caravan 8.3 Hinged windows 8.3.1 General 8 The hinged windows of the caravan have a locking device, i.e. the hinged window automatically locks into place in the desired position after opening. The number of locking levers at the bottom edge of the window varies depending on the window width. 1 Locking lever on hold-open hinge 2 Locking lever at bottom edge of window 3 Hold-open hinge 3 1 2 Fig. 15 Hinged windows Opening the window: Open the two locking levers (Fig.
8 Living in the caravan 8.3.2 Opening/closing the windows To open and close the hinged windows, open or close all locking levers on the respective hinged window. 3 45 Fig. 16 1 Securing button 2 Lever 3 Latch plate 4 Fork 5 Locking catch 12 Opening and closing the hinged windows Opening the window: If the locking lever has a securing button (Fig. 16/1), press and hold down the securing button. Turn the lever (Fig. 16/2) to the middle of the window. Open all window locks. Open the window.
8 Living in the caravan 8.3.3 Permanent ventilation Caution! Cracks in the window Close only the levers (Fig. 15/2) at the bottom edge of the window in the "permanent ventilation" position, otherwise the window pane is bent. This could result in the formation of cracks in the acrylic glass window. Ensure all bottom catch bars are closed in the same position, otherwise, the window could be distorted. 2 34 Fig.
8 Living in the caravan 8.3.4 Sliding windows (special equipment) 1 1 Window 2 Handle 1 Window 2 Handle 3 Catch 2 Fig. 18 Opening the sliding window Opening the sliding window: Press the handle (Fig. 18/2). Slide the window (Fig. 18/1) to the side. 1 3 2 Fig. 19 Closing the sliding window Closing the sliding window: Push the window (Fig. 19/1) until it is closed and the handle (Fig. 19/2) latches into place in the catch (Fig. 19/3).
Living in the caravan 8.4 Window blinds and insect screens 8.4.1 Blind and insect screen - version 1 8 Caution! Damage to insect screen When you unlock the blind/insect screen, hold on to the insect screen (Fig. 20/3), otherwise it will snap up with spring tension. Snapping up could damage the screen spring and the insect screen. 3 1 Blind 2 Pushbuttons 3 Insect screen 4 Catch 4 2 1 Fig. 20 Opening and closing of the blind and insect screen - version 1 The blind (Fig.
8 Living in the caravan 8.4.2 Blind and insect screen - version 2 Caution! Damage to insect screen When you unlock the blind (Fig. 21/1) and insect screen(Fig. 21/2), hold on to them, otherwise they will shoot up with spring tension. Shooting up could damage the screen spring and the blind/insect screen. 1 Fig. 21 1 Insect screen with handle 2 Blind with handle 2 Opening and closing of the blind and insect screen - version 2 The blind (Fig. 21/1) and the insect screen (Fig.
8 Living in the caravan 8.4.3 Blind and insect screen - version 3 The blind (Fig. 22/3) and the insect screen (Fig. 22/2) are both located in the upper window frame. The insect screen follows the blind. 1 Fig. 22 2 3 1 Handle 2 Insect screen with handle 3 Blind 4 Handle bar 4 Opening and closing of the blind and insect screen - version 3 Opening / closing the blind: Pull the blind (Fig. 22/3) down or up with the grip bar (Fig. 22/4). The blind (Fig.
8 Living in the caravan 8.5.2 Roof hood with operating bar (special equipment) The roof hood with operating bar can be opened by tilting to one side. 3 6 2 5 4 1 Glass dome 2 Locking button 3 Bar 4 "Closed" position 5 "Ventilation" position 6 "Open" position 1 Fig. 23 Opening / closing the roof hood with operating bar Opening the roof hood: To open the glass dome (Fig. 23/1), press the locking button (Fig. 23/2) and pull the bar (Fig. 23/3) downwards. Push the bar (Fig.
Living in the caravan 8 Closing the roof hood: Turn the hand crank (Fig. 24/1) again until a resistance can be felt. Before you fold in the hand crank again, a light initial tension must be present on the crank. If required, loosen the attachment screw, take the crank out of the gearing and reposition the crank. Then place the crank onto the gearing again and screw tight. Check the locking by attempting to lift the glass dome by hand. Close the locking lever as required (Fig. 16). 8.5.
8 Living in the caravan 1 Rotary knob 1 Fig. 26 Opening / closing the roof hood Opening the roof hood: Turn the rotary knob (Fig. 26/1) clockwise to open the glass dome. Turn the rotary knob only until a resistance can be felt. The roof hood is now in the maximum open position. Any desired interim position is possible. Closing the roof hood: Turn the rotary knob (Fig. 26/1) anticlockwise until a resistance can be felt. Then lock the roof hood.
Living in the caravan 8.5.5 8 Roof hood blind and insect screen running in opposite directions Important! • Both are continuously adjustable and can be operated together or separate from each other. • Only close the blind to a maximum of 75% during direct sunlight. Air must be able to circulate. 3 Fig. 27 1 1 Inner frame 2 Blind 3 Insect screen 2 Roof hood blind and insect screen running in opposite directions The blind (Fig. 27/2) and the insect screen (Fig.
8 Living in the caravan 8.5.6 Roof hood blind and insect screen running in the same direction Important! • Both are continuously adjustable and can be operated together or separate from each other. • After releasing the grip, the blind is automatically clamped into place in the inner frame of the roof hood. • Only close the blind to a maximum of 75% during direct sunlight. Air must be able to circulate. 1 Fig.
Living in the caravan 8.5.7 8 Roof hood blind and insect screen running together Important! • Both folding screens are continuously adjustable and can be operated together or separate from each other. • After releasing the operating bar, the folding screen remains in the position reached. • The insect screen is integrated into the second operating bar and allows maximum amount of light or darkening with insect screen function.
8 Living in the caravan 8.6 Control panel Depending on the model, the following control panels have been installed in the caravans: • LT 413 (with power supply unit CSV 4xx, Chapter 10.3.2) • EN panel (with power supply unit BCA, Chapter 10.3.3) Battery voltage and, depending on the model, water tank and fuel tank levels can be queried via the control panels. The control panels are located indoors. 8.6.1 LT 413 control panel 2 3 4 1 Fig.
8 Living in the caravan "Tank level" button: Push down the button (Fig. 30/6) to indicate the level of the water tank. Actuating the button at the top has no effect. The "Tank fill level" Indicator (Fig. 30/5) shows how much water is in the water tank. Switching the water supply on / off: Press the "Water supply" switch (Fig. 30/7) to switch the supply voltage for the water pump on or off. Opening a water tap switches the water pump on.
8 Living in the caravan 8.7 Central lighting control Some vehicles have a central system for switching and dimming various lighting units. Channels 1 to 8 can be switched in series. Channel 9 is not normally served by the central switch but can be switched on and off using the Standby button of the central lighting control. 3 1 4 5 2 230 V AC 10100053 Fig.
8 Living in the caravan Important! • The symbols shown and the associated configurations can vary from vehicle to vehicle. Your ADRIA specialist dealer will explain the configuration installed in your vehicle during handover. • The dimming function cannot be used for certain channels depending on the lighting elements used. • Use the Checklist in Chapter 21 should problems arise. You can assign the channels to series 1 and 2 yourself. 1 8 9 2 3 6 7 4 5 10 11 10100052 Fig.
8 Living in the caravan Function / channel System is switched on Press for about 1 second Channel 1 to 8 Additional button. Press longer System is switched off (Standby) Approx. 0.5 s Switch off. Dimming. Switch on. Press button about 1 second. Hold button pressed for about 1 second. Channel 9 also switches on. Last dimming status is saved. Brightness is reduced at first and then increased or reduced every time pressed. Function as for channel 7. Function as for channel 7.
Living in the caravan 8.9 8 Furniture locks Caution! Damage to the handles Do not pull too hard on a handle when the respective door, flap or drawer cannot be opened. First unlock the drawers before opening them. To close the bathroom door, always hold the door handle pressed fully down. Depending on the production series, there can be different locking systems. The drawings serve only to show the operating principle. Differences in form are possible. 8.9.
8 Living in the caravan 8.9.2 Furniture locks - version 2 1 Locking button 1 Fig. 35 Furniture lock - version 2 Opening: Push the locking button, the button springs out. The lock is unlocked. Open the cabinet door, flap or drawer. Closing: Close the cabinet door, cabinet flap or drawer. Push in the locking button (Fig. 35/1) until it latches into place. The lock is locked. 8.9.3 Furniture locks - version 3 1 Flap 1 10100058 Fig.
Living in the caravan 8 Closing: Close the cabinet door, flap or drawer. Lightly press cabinet door, flap or drawer approximately in the middle. The pushing position is marked with "Push". The cabinet door, flap or drawer is locked. 8.9.4 Furniture locks - bathroom 1 2 1 Cabinet door 2 Latch 1 10100062 Fig. 37 Furniture lock - bathroom Opening: Put your fingers in the recess of the cabinet door (Fig. 37/1) and pull the latch (Fig. 37/2) on the rear. The lock is unlocked.
8 Living in the caravan 8.10 Bathroom unit 8.10.1 Washbasin, foldable Caution! Damage to mirror and washbasin Always lower the washbasin slowly. 1 2 1 Grip hole 2 Washbasin (folded up) 10100060 Fig. 38 Washbasin, foldable - folded up Folding the washbasin down: Grip inside the grip hole on the mirror (Fig. 38/1) and carefully pull the washbasin (Fig. 38/2) with mirror. Fold the washbasin (Fig. 38/2) with mirror down. 1 2 1 Water tap 2 Washbasin 10100059 Fig.
Living in the caravan 8.10.2 8 Folding shower door (special equipment) - version 1 Caution! Damage to folding door or bathroom unit Secure the folding door (Fig. 40/1) with the lever (Fig. 40/2). If you leave the parking area with the caravan and the folding door is not secured, it can open and close uncontrolled during cornering. X X 1 Folding door 2 Lever 2 1 Fig. 40 Folding shower door - version 1 Closing: Unlock the lever (Fig. 40/2) before you close the folding door (Fig. 40/1).
8 Living in the caravan 8.10.3 Folding shower door (special equipment) - version 2 Caution! Damage to folding door or bathroom unit Secure the folding door (Fig. 41/1) with the retaining strap (Fig. 41/2). If you leave the parking area with the caravan and the folding door is not secured, it can open and close uncontrolled during cornering. 1 Folding door 2 Retaining strap 2 1 Fig. 41 Folding shower door - version 2 Closing: Loosen the retaining strap (Fig.
Living in the caravan 8.11 8 TV equipment (special equipment) Caution! Damage to the vehicle Before starting the journey, you always have to lower and lock the antenna. Retract, lay it flat and secure the satellite dish before starting the journey. Lock the antenna mast into place to prevent twisting of the satellite dish. Caution! Damage to the cables Make sure the cables always have enough room to move. Caution! Damage to the appliance Check all locking grips are engaged before each journey.
8 Living in the caravan 8.11.1 TV slide-out and small parts shelf Caution! Damage to the cables Make sure the cables always have enough room to move. Some vehicles are fitted with a TV bracket combined with a small parts shelf. The TV (flat screen) can be fitted on the TV fixing surface (Fig. 42/2) on the rear side of the small parts shelf (Fig. 42/3). You can swivel the TV towards the sleeping or living area when in use.
Living in the caravan 8.11.2 8 TV bracket with ceiling guide rail Caution! Damage to the cables Make sure the cables always have enough room to move. Caution! Damage to the appliance Check all locking grips are engaged before each journey. Check the locking screw is tightened before driving. Some vehicles are fitted with a TV bracket with ceiling guide rail. The TV (flat screen) can be mounted on the fastening plate. You can swivel the TV towards the sleeping or living area when in use.
8 Living in the caravan 1 Locking grip for turning 2 Locking grip for swivelling 3 Locking screw 3 1 2 Fig. 44 10100063 TV bracket with ceiling guide rail - adjustment option Shifting the TV bracket: Loosen the locking screw (Fig. 44/3). Shift the TV bracket. Tighten the locking screw (Fig. 44/3) by hand. Turning or swivelling the TV bracket: To adjust, pull the locking grip (Fig. 44/1) or (Fig. 44/2) and engage the locking grip again when finished.
Living in the caravan 8.11.3 8 TV bracket with wall mounting Caution! Damage to the cables Make sure the cables always have enough room to move. Caution! Damage to the appliance Check the TV bracket is secured with the locking bracket and locking screw before driving. Some vehicles are fitted with a TV bracket with wall mounting. The TV (flat screen) can be mounted on the fastening plate. You can swivel the TV towards the sleeping or living area when in use.
9 Sleeping arrangements 9 Sleeping arrangements 9.1 Beds 9.1.1 Fixed bed Caution! Risk of damage Lower the slatted frame slowly. Do not let it just drop down. A bed storage compartment is under each bed. The bed storage compartment can be accessed either by swivelling the bed up or through an outside storage flap. Swivel the slatted frame up to access the bed box. 1 Slatted frame 1 10100025 Fig. 46 Opening the fixed bed Opening the bed storage compartment: Lift the slatted frame (Fig. 46/1).
9 Sleeping arrangements 9.1.2 Bunk beds Warning! Accident hazard Do not use the bunk bed for storage of luggage during the journey. Place only the required bed linen on the bunk bed during the journey. Never allow small children to remain in the bunk bed without supervision. For children under 6 years of age, ensure they cannot fall out of the bunk bed. Use separate children's beds or travel cots suitable for small children. Always use the upper bunk bed with hung-in safety net.
9 Sleeping arrangements 9.1.3 Foldaway bed, wall unit (special equipment) Warning! Accident hazard Always open and close the foldaway bed with 2 persons. Always use the foldaway bed with hung-in safety net. Never allow children to remain in the foldaway bed without supervision. For children under 6 years of age, ensure they cannot fall out of the foldaway bed. Use separate children's beds or travel cots suitable for small children. The maximum load on the foldaway bed is 50 kg.
9 Sleeping arrangements 3 3 1 Slatted frame 2 Guard against falling 3 Buckle latch of guard belts 2 1 10100022 Fig. 50 Opening the foldaway bed wall unit Roll out the slatted frame (Fig. 50/1). Lay the mattress on the frame (not shown). Fix the guard against falling (Fig. 50/2) on the vehicle ceiling with the buckle latches (Fig. 50/3). Closing the foldaway bed: Close the foldaway bed wall unit in reverse sequence. 9.2 Lowering the table 9.2.1 Suspended table 1 Fig.
9 Sleeping arrangements 1 Table foot 2 Locking button 2 1 Fig. 52 Swinging the table foot down Press the locking button (Fig. 52/2) to unlock the table foot (Fig. 52/1). Swing the table foot down 90°. Then place the table in the bottom position against the seat. 9.2.2 Lowering the telescopic table 1 Locking lever 1 10100020 Fig. 53 Lowering the telescopic table Hold the table top with one hand in the middle of the table Turn the locking lever (Fig.
Sleeping arrangements 9.2.3 9 Lowering the swivelling table 1 Table top 2 Grip 1 2 10100019 Fig. 54 Lowering the swivelling table Push the grip (Fig. 54/2) upwards. Swivel the table top (Fig. 54/1) downwards in an arch until the grip engages.
10 10 Power supply Power supply Caution! Short-circuit, corrosion and cable break For your own safety, have the electrical system checked at least once a year by an authorised workshop. 10.1 230 V power supply The vehicle can be connected to an external power supply with 230 V which must be protected with a 30 mA ground-fault circuit breaker (fault current). 10.1.
Power supply 10.2 10 Fuse protection of the 230 V electric circuit in the vehicle The external 230 V power supply of the vehicle is protected with a 13 A circuit breaker. In addition to the circuit breakers, a ground-fault circuit breaker (special equipment) is installed in some vehicles. The ground-fault circuit breaker protects persons against electric shock if the insulation of electrical appliances is defective.
10 Power supply 10.3 12 V power supply 10.3.1 Power supply unit CSV 300-X Warning! Risk of burns The power supply unit becomes hot when in use. Do not touch. Replace defective fuses only when the power supply unit has been de-energised. Caution! Damage to power supply unit Replace defective fuses only when the power supply unit has been de-energised. Replace defective fuses only when the cause of the defect is known and has been remedied. Never bridge or repair fuses.
Power supply 1 2 3 10 4 5 7 6 5 10100066 Fig.
10 Power supply Placing into service: The system is ready for operation when the 12 V supply from the towing vehicle or the 230 V mains voltage is connected. The unit does not have to be switched on separately. Vehicle flat blade fuses The vehicle flat blade fuses (Fig. 57/3) protect the various electric circuits. A tool to exchange the vehicle flat blade fuses (FK-puller) is fitted next to the vehicle flat blade fuses. For more information, see the separate instructions from the manufacturer.
Power supply 10.3.2 10 Power supply unit CSV 4xx The power supply unit is normally fitted in a cabinet or storage space and can be accessed to exchange fuses. Depending on the vehicle equipment, different voltage supply units of the 4xx series are used (xx stands for the different versions of the appliance). For the exact type of the power supply units used in your vehicle, check the nameplate on the appliance and the separate instructions from the manufacturer.
10 Power supply 1 2 3 4 11 Fig. 58 10 9 876 5 10100106 Power supply unit CSV 4xx (Figure can deviate from actual unit).
Power supply 10 Battery selector switch (not CSV 400) If the battery selector switch (Fig. 58/6) is set to the wrong position, the living area battery could become damaged. Switching the battery selector switch (not CSV 400): Disconnect the power supply unit from the mains before setting the battery selector switch (Fig. 58/6) to a different position. Selection of lead-gel battery: Set the battery selector switch to "Gel". Selection of lead-acid battery: Set the battery selector switch to "Acid".
10 10.3.3 Power supply Power supply unit type BCA Warning! Risk of burns The power supply unit becomes hot when in use. Do not touch. Replace defective fuses only when the power supply unit has been de-energised. Caution! Damage to power supply unit Replace defective fuses only when the power supply unit has been de-energised. Replace defective fuses only when the cause of the defect is known and has been remedied. Never bridge or repair fuses.
Power supply 10 Placing into service: The 12 V main switch on the control panel serves to switch the system on (Chapter 8.6.2). Vehicle flat blade fuses The vehicle flat blade fuses (Fig. 59/3) protect the various power circuits For more information, see the separate instructions from the manufacturer. 10.3.4 Starter battery (in towing vehicle) Caution! Discharging of starter battery The capacity of the starter battery is limited.
10 10.3.5 Power supply Living area battery (special accessory) Warning! Deflagration The use of acid batteries as living area batteries in the caravan is not allowed. The installation area is not equipped for accommodation of an acid battery. Only gel or AGM batteries may be used as living area battery. The living area battery can be charged in two ways: • With the towing vehicle generator, i.e. while the engine is running. • All major appliances such as refrigerator, heater, water pump, etc.
Power supply 10.4 10 Central lighting control - light assignment Light assignment to channels of the central lighting control is set at the factory and can only be modified by an ADRIA specialist dealer.
10 Power supply Before changing fuses, see the following table for function, value and colour of the respective fuses: Amperage Colour Function Installation location 2A Grey Fuse of living area battery In the 12 V power supply unit or next to the living area battery 3A Violet Fuses of Thetford toilet In the housing frame of the Thetford cassette or in the 12 V power supply unit 20 A Yellow Fuse of refrigerator In the 12 V power supply unit 50 A Red Fuse of 12 V power supply unit Next to
Power supply 10.6 10 Electrical diagrams 230 V Caution! Damage to the electrical system Have maintenance and repair work performed by an authorised workshop. Improper maintenance and repair work voids your warranty claims. See the following electrical diagrams for the exact layout of the electrical components and wiring. These diagrams are required for possible repairs and maintenance. A Power input 220-240 V, 16 A, 2P+T B Main fuse with FI 220-240 V, 25 A, 0.
10 Power supply 10100044 Fig. 61 Electrical diagram 230 V: AVIVA-ALTEA-ACTION-ADORA 10100110 Fig.
Power supply 10.7 Electrical diagrams for 12 V supply from towing vehicle No. Function Type A1 Brake light and rear light PY21/5W A2 Reversing light P21W A3 Rear fog light P21W A4 Direction indicator PY21W B1/B2 License plate light C5W E Contour light, red/white W5W E1 Side marker light - orange LED F1/F2 Contour light, front - white LED M 3rd brake light LED N Earth connection O Caravan charging station, power supply unit U Connector plug for towing vehicle Tab.
10 Power supply 10100109 Fig. 63 Electrical diagram 12 V: ASTELLA-ALPINA 10100042 Fig.
Power supply Electrical diagrams, voltage supply 10100046 10.8 10 Fig.
Power supply 10100047 10 Fig.
10 10100108 Power supply Fig.
Power supply 10100107 10 Fig.
Gas system 11 Gas system 11.1 General information about the gas system 11 Familiarise yourself with the safety instructions for handling gas. For general safety instructions concerning the topic of "gas", see the "Safety instructions for the gas system" (Chapter 2.5).
11 Gas system • • 11.2 In order to ensure continuous exchange of air in the vehicle, do not cover the forced ventilation in the roof hoods and in the entrance nor the mushroom ventilators. When there is snowfall in winter, keep the forced ventilation free from ice and snow! (Chapter 17.3). Gas cylinder compartment Caution! Gas cylinder compartment Always keep the forced ventilation in the floor free! Always keep gas cylinders upright and lashed. Do not use the gas cylinder compartment as storage space.
Gas system 11.3.3 11 Information on liquid gas Liquid gas characteristics: • • • • • 11.4 Liquid gas has no colour. It smells of garlic. It is heaver than air and collects on the ground after escaping. It is combustible and can burn rapidly when it escapes uncontrolled or explode when sparks occur. In enclosed areas, it displaces the breathing air; risk of suffocation! Reference values for gas consumption The gas consumption depends on how intensively the connected appliances are used.
11 11.5 Gas system Handling gas cylinders Caution! Danger when handling gas cylinders Read the safety instructions on the gas cylinder! Operate gas cylinders only with the pressure regulator connected! Do not smoke in the vicinity of the gas cylinders! Any kind of open flame must be avoided! This is valid in particular when replacing gas cylinders. Never lubricate threads and seals on the pressure regulator with grease.
Gas system 3 1 Fig. 69 11 1 Closed 2 Open 3 Gas pipe to the gas appliance 2 Quick-action stop valves - positions Using the gas appliances: Open the respective quick-action stop valve to put the desired gas appliance into service. – Quick-action stop valve closed (Fig. 69/1): The arrows on the quick-action stop valve are positioned on the gas appliance crosswise to the direction of the gas pipe (Fig. 69/3). – Quick-action stop valve open (Fig.
11 11.7 Gas system External gas connection (special equipment) Danger! Risk of explosion Only use a suitable adapter to connect to the external gas connection. Only connect gas appliances to the external gas connection that are designed for 30 mbar operating pressure. Check leak tightness of the external gas connection every time a gas appliance is connected. Gas escapes into the air when the gas connection leaks.
Water and waste water 12 Water and waste water 12.1 Water supply 12 Warning! Health hazard Formation of bacteria and algae in the water tank. Change the water at regular intervals including the boiler contents (e.g. twice a week). After the end of every journey or after 4 weeks at the latest, the water tank must be drained, cleaned thoroughly and left open (venting). Use disinfectant for the water tank. Caution! Damage to the water pump Pumps can run hot without water and can be damaged.
12 12.1.1 Water and waste water Water tank 4 2 3 1 Water tank 2 Filler neck 3 Lockable cap 4 Service cover 5 Drain plug 5 1 Fig. 72 Filling the water tank - external Filling the water tank (external): Switch the water pump off (actuate the button on the control panel, Chapter 8.6). Unlock and open the lockable cap (Fig. 72/3) on the filler neck (Fig. 72/2). Fill water with a water canister, a watering can or a hose into the water tank. Replace, close and lock the cap.
Water and waste water 12.1.2 12 Ultraflow external water connection (special equipment) Some vehicles are fitted with an external water connection (Truma Ultraflow). The external water connection can only be used with a suitable adapter. Depending on the equipment, separate water consumers can be connected to the external water connection (e.g. outdoor shower) or to an external water tank. 1 2 1 External water connection flap 2 Socket with switch contacts 10100055 Fig.
12 12.1.4 Water and waste water Faucet Drawing of hot and cold water is performed with a single-lever faucet. Depending on the installation position, the water temperature is controlled either by raising and lowering or swivelling of the lever 1 2 Fig. 75 1 Lever (raising/lowering) 2 Lever (swivelling) Faucet Operating the faucet: Move the lever (Fig. 75/1) upward to turn on the water pump. Water is running. Adjust the desired temperature by swivelling the lever (Fig. 75/1).
Water and waste water 12.2 12 Draining the water and waste water system Warning! Health hazard Prevent the formation of bacteria and algae in the water tank. Change the water at regular intervals including the boiler contents (e.g. twice a week). After the end of every journey, the water tank including the boiler must be drained, cleaned thoroughly and left open (venting). Thoroughly clean the hoses after the end of each journey. Use disinfectant for the water tank.
13 Heater & hot water 13 Heater & hot water 13.1 General heating information Danger! Risk of fire The person using the heating must have the heat exchanger of the Truma heating replaced at the latest after 30 years. Only the heating manufacturer or an authorized workshop can exchange the heat exchanger. Heating spare parts must always be approved as spare parts by the manufacturer. Danger! Risk of explosion Never let unignited gas flow out.
Heater & hot water 13 Switching the warm air heater off: Set the control knob (Fig. 77/1) of the heating to "0". If the heating is not going to be used for some time, close the quick-action stop valve "Heating" and the shut-off valve on the gas cylinder. For more information, see the separate instructions from the manufacturer. 13.3 Circulation fan (special equipment) The circulation fan allows better circulation of the warmth from the warm air heater. 5 4 1 Fig.
13 Heater & hot water 1 5 7 Ultraheat 3 2000 1 Rotary switch for levels 2 "Off" position 3 Temperature controller 2 1 9 500 1000 3 230 V Fig. 79 10100011 Ultraheat control with room thermostat Switching Ultraheat on: Connect the vehicle to the 230 V supply (see Chapter 10.1.1). Turn the rotary switch (Fig. 79/1) to the desired capacity level 500 W, 1000 W or 2000 W. Set the thermostat (Fig. 79/3) to the desired temperature. Switching Ultraheat off: Set the rotary switch to (Fig.
Heater & hot water 1 2 1 Transformer 2 Overload protection pin 13 10100008 Fig. 80 "Electrical floor heating" transformer The transformer (Fig. 80/1) for the electric floor heating is fitted in the seat chest or bed box depending on the model. 1 1 Control lamp 2 Rocker switch 2 10100002 Fig. 81 "Electrical floor heating" switch Using the electrical floor heating: Check the circuit protection for the 230V power supply at the camping site is adequate. (350 W - 1.
13 13.6 Heater & hot water Truma Therme (special equipment) Therme 230 V Fig. 82 1 Switch 1 10100006 Truma Therme rocker switch You can run the Truma Therme with either the 230 V supply (electric model), with warm air from the heating system or with both types of energy. The Truma Therme heats about 5 l of water to maximum 65° C. The switch serves to start (Fig. 82/1) the electric operating mode. The control lamp in the switch is on during operation.
Heater & hot water 1 13 Drain cocks 1 10100007 Fig. 83 Truma Therme Emptying the Truma Therme : Place a collector under the drain openings of the drain cocks. Switch the rocker switch (Fig. 82/1) for the Truma Therme off. The control lamp in the switch is off. Open all taps. Turn the drain cocks (Fig. 83/1) anticlockwise to open. Check that the Therme is completely empty. Dispose of the water collected at an approved location.
13 13.7 Heater & hot water Truma Boiler (special equipment) Danger! Risk of poisoning and suffocation when the exhaust cowl is fitted on the right When the awning is in place and the heater operates in gas mode, the heater exhaust gases can collect under the awning. There exists the risk of poisoning and suffocation due to lack of oxygen and the possibly generated odourless and toxic carbon monoxide (CO). Ensure adequate ventilation! Caution! Type of danger Never run the boiler without water.
Heater & hot water 13 Leave the taps open until the water flows out without bubbles. The boiler is now filled with water. Close all taps. Emptying the boiler: Place a collector under the drainage opening of the drain cock. Switch off the rocker switch for electric operation (Fig. 86/1) and the rotary knob for gas operation (Fig. 85/3). The control lamps in the switches are off. Switch off the 12 V supply. Open all taps. Open the safety/drain valve (Fig. 84/2). To do this, set the rocker arm vertical.
13 13.7.3 Heater & hot water Boiler in electric mode Boiler EL 1 230 V Fig. 86 Rocker switch 1 10100004 Boiler rocker switch for electric mode The water temperature is preset to about 70° C in e lectric mode and cannot be changed. Switching the boiler on in electric mode: Connect the vehicle to the 230 V supply. Press the rocker switch (Fig. 86/1) at the top. The green control lamp "Operation" goes on. Switching the boiler off in electric mode: Press the rocker switch (Fig. 86/1) at the bottom.
Heater & hot water 13.8 13 Alde warm water heater Important! Central heating Alde Compact has an "ionizing flame control", i.e. if the flame goes out, the electronic control panel attempts to ignite the flame again. If the flame does not ignite within 10 seconds, the solenoid valve shuts off the gas supply and the electronic control panel. Reset by switching off and restarting the heater with the On/Off button (Fig. 87/8).
13 13.8.2 Heater & hot water Menu overview 1 Heating with gas Press the "On" button to switch gas operation on. Press the "Off" button to switch gas operation off. 4 2 3 Select the power (Off, 1 kW, 2 kW or 3 kW) by pressing the "+" or "-" button. Some heaters only have 1 kW or 2 kW. 2 5 1 Heating with electricity 3 Hot water volume Press the "+" button to increase the hot water volume for 30 min. Press the "–" button to return to the basic settings for hot water before 30 min. have expired.
Heater & hot water 13 To start the heater, press the On/Off button (Fig. 87/8). The Start screen is displayed. The heater starts with the settings used last. Control of central heating with the control panel (Fig. 88/1 to 5). In summer, when only hot water is required, the set temperature value must be lower than the prevailing temperature to prevent a start of the pump in the heating system. For more information, see the separate instructions from the manufacturer. 13.
14 Cooking 14 Cooking 14.1 Cooking with gas Danger! Risk of poisoning due to carbon monoxide (CO) and lack of oxygen Always open a window or a skylight as well when the gas stove is switched on. Never cover the forced ventilation in the roof hoods and in the entrance as well as the mushroom ventilators.
Cooking 14.2 14 Gas stove Caution! Defective cooking area The burner does not operate properly. The flame goes out again and again despite the control knob being depressed for an extended period of time. The thermal element is bent or defective. Have defective thermal elements replaced by an authorised workshop. We recommend yearly inspection by a specialist. Important! • Always make sure the respective control knob is set to "Off" when you are finished using the cooking stove, the grill or the oven.
14 Cooking To switch off, turn the control knob clockwise to the "0 position". The flame goes out and the flame safety device automatically shuts off the gas supply. Close the quick-action stop valve (Fig. 69/3). For more information, see the separate instructions from the manufacturer. 14.3 Extractor hood (special equipment) The extractor hood is located above the gas stove. 1 Extractor hood 2 Rocker switch 1 Extractor hood 2 Extractor hood rocker switch 3 Lighting rocker switch 2 1 Fig.
Cooking 14.4 14 Microwave oven (special equipment) Danger! Danger for health Only allow qualified personnel to repair he microwave oven. Serious health risk through incorrect repairs! Do not remove the protection against microwave energy escaping. Do not use the microwave oven when the door seal is damaged. Do not leave the microwave oven unattended when in use. If smoke occurs, switch microwave oven off and disconnect the power supply. Leave the microwave oven closed.
14 14.5 Cooking Gas stove with grill and oven (special equipment) Warning! Risk of burns by hot surfaces Always wear protective gloves when handling hot items. Protect yourself and your children from contact with hot parts. After use, allow the grill and the oven to sufficiently cool down inside and outside. Caution! Damage to oven Never use the oven for heating the vehicle! 14.5.
Cooking 14 Using the grill: Make sure the gas supply or the gas cylinder are connected and switched on. Open the door, press the control knob and turn it clockwise to the large flame symbol. Keep the knob depressed while holding a lit match to the burner. When the flame is burning, keep the knob depressed for another 10 to 15 seconds. If the flame does not ignite within 15 seconds, release the control knob and wait at least one minute before repeating steps 2 to 4.
15 15 Refrigerator & freezer Refrigerator & freezer The refrigerator and the freezer compartment form a mechanical unit. To ensure optimum function, the appliance should stand level, if possible. However, it is also suitable for inclined positions to a certain degree. The refrigerator and freezer compartment combination can be operated optionally with 230 V, 12 V or liquid gas. Operation with 230 V or gas is recommended because these are most efficient.
Refrigerator & freezer 15.1 Controls 15.1.1 Opening and locking the door 15 Caution! Damage to refrigerator door Always make sure the refrigerator door is correctly locked before moving the vehicle. 4 Fig. 94 1 2 1 Freezer compartment latch 2 Refrigerator latch 3 Lock the door 4 Unlock the door 3 Refrigerator lock Dometic 7 series Opening the refrigerator Dometic 7 series: Slide latch (Fig. 94/1) or (Fig. 94/2) to the left (Fig. 94/4). Open the refrigerator door.
15 Refrigerator & freezer 1 Unlock button 1 10100033 Fig. 95 Refrigerator lock Dometic 8 series Opening the refrigerator Dometic 8 series: Press the unlock button (Fig. 95/1) down and open the refrigerator door. Closing the refrigerator Dometic 8 series: An automatic lock is fitted on the refrigerator door. When you close the refrigerator door and press it on firmly, the door locks automatically. Locking Thetford refrigerators: An automatic lock is fitted on the refrigerator door.
Refrigerator & freezer 15.1.3 Dometic 8 series with manual mode selection and automatic ignition MES 1 Fig. 97 15.1.4 15 2 3 5 4 Refrigerator controls (Dometic 8 series) 1 On/Off / energy selector button 2 "Malfunction" LED indicator 3 "Mode" LED indicator 4 "Temperature range" LED indicator 5 Temperature setting switch Dometic 8 series with manual mode selection and battery ignition. 1 2 3 4 5 6 7 10100032 Fig.
15 Refrigerator & freezer 15.1.5 Thetford Premium LCD 2 Fig. 99 5 1 3 Refrigerator and freezer compartment controls (Thetford Premium LCD) 1 Main switch 2 "Mode selector" switch 3 "Cooling capacity" selector switch 4 LCD display 5 "Mode" LED indicator 1 Fig. 100 4 1 Mode 2 Cooling capacity / Fault / Service 2 LCD display For more information, see the separate manufacturer's operating instructions. 15.2 Placing into service 15.2.
Refrigerator & freezer 15.2.3 15 230 V mode Select the 230 V mode only when an external 230 V supply is connected. Before starting the journey, obtain information on the voltage in the country to be visited. 15.2.4 Gas mode Danger! Risk of explosion at petrol stations! Open flames are prohibited at petrol stations! – Switch the refrigerator off using the power selector switch! Caution! Using gas Only use liquid gas to run the refrigerator (Chapter 11.3).
15 15.2.5 Refrigerator & freezer Winter mode Important! Attach the winter covers also when the vehicle is taken out of service for an extended period of time or cleaned on the outside. Check in winter operation: Check regularly that the ventilation grilles have not been blocked by snow, ice, leaves or similar. When the outside temperature drops below +8°C, the winter covers (special accessory) should be fitted to the ventilation grilles This protects the refrigerator unit from excessively cold air.
Toilet 16 16 Toilet Caution! Damage to the environment Use an environment-friendly and biodegradable chemical toilet additive for the toilet. – The ventilation will remove merely the odour but not germs and gases. Germs and gases can have a detrimental effect on the rubber seals. Caution! Material breakage Do not sit on the toilet lid. – The lid is not designed to bear the weight of a person and could break. Important! • Do not leave water in the bowl when the toilet is not used.
16 Toilet 16.1 Toilet system 16.1.1 Thetford Cassette C-200 S and C-260 S 2 3 4 4 3 5 1 Fig. 101 Thetford C-200 S and C-260 S 1 Lever for opening the valve blade 2 Operator panel 3 Flush button 4 Waste level indicator 5 Automatic ventilator (special equipment) Before use: Turn the toilet bowl to the desired position using both hands. Before flushing, use the lever (Fig. 101/1) to open the valve blade. To activate the control panel, press the flush button (Fig. 101/3) once.
Toilet 16.1.2 16 Thetford Cassette C-402 C The C-402 C toilet has an own water tank. Caution! Damage to toilet and vehicle Do not leave water in the bowl when the toilet is not used. This can cause blockages. Do not fill the flushing water tank more than half full when travelling. Otherwise water damage could occur on your vehicle.
16 16.1.3 Toilet Water tank toilet C-402 C 4 3 2 1 1 Outer door 2 Cassette emptying spout 3 Water filling funnel 4 Water filling funnel cap 5 Water level indicator 5 10100054 Fig. 103 Water tank toilet C-402 C The water tank holds 15 liters. Filling the water tank: Open the outer door (Fig. 103/1) for the cassette and water fill funnel. Swivel the cassette emptying spout (Fig. 103/2) out about 90° and remove the water tank extension (Fig. 107/4). Swivel the water filling funnel (Fig.
Toilet 16.1.4 16 Thetford Cassette C-403 L Caution! Do not leave water in the bowl when the toilet is not used. This can cause blockages. 12 2 3 4 5 10100036 Fig. 104 1 Lever for opening the valve blade 2 Control panel and waste level indicator 3 Flush button 4 Compartment for toilet fluid (only on tall model, only accessible from the outside) 5 Sliding cover (only accessible from the outside) Thetford C-403 L Before use: Before flushing, use the lever (Fig.
16 16.2 Toilet Cassette Caution! Danger for the environment Use an environment-friendly and biodegradable chemical toilet additive for the toilet. The cassette may be emptied only at camping sites with suitable waste water treatment plants or special waste disposal stations (e.g. at parking sites for camping vehicles).
Toilet 16.2.2 16 Thetford Cassette C-260 S 2 3 5 7 4 Fig. 106 1 8 1 Cassette 2 Swivelling emptying spout 3 Automatic holding tank vent valve 4 Pull-out hand grip / latch 5 Sliding cover 6 Valve blade 7 Vent plunger 8 Removable mechanism 6 Thetford Cassette C-260 S The cassette (Fig. 106/1) has a capacity of 18 l and should be emptied when the level indicator (Fig. 101/4) lights. Do not allow the cassette to become overfilled. 16.2.
16 16.2.4 Toilet Emptying the cassette Removing the cassette: Close the valve blade (Fig. 101/1), (Fig. 102/1), (Fig. 104/1) in the toilet. Open the outer access door. Release the cassette with the catch (Fig. 105/9), (Fig. 106/4) or (Fig. 107/1) and remove. When the cassette is pulled out, the valve blade (Fig. 105/7), (Fig. 106/6) or (Fig. 107/5) is hygienically closed by the sliding cover (Fig. 105/5), (Fig. 106/5) or (Fig. 107/6).
Toilet 16.3 16 Placing the toilet out of service Important! Empty the cassette and water tank when the vehicle is not heated and there is a risk of frost. Placing the toilet out of service: Place a sufficiently large container underneath the drain plug of the water tank. Open the drain plug, drain the water tank completely and allow to dry. Empty the cassette (Chapter 16.2). Leave the emptying spout open to allow the tank to dry. Clean the toilet (Chapter 19.2.6).
17 Winter camping 17 Winter camping 17.1 Travelling in winter Winter camping is becoming more and more popular. Depending on the model and equipment, your ADRIA vehicle is conditionally suitable for use in winter. If you pay attention to the following information, your winter holiday in your own vehicle will become proper winter fun. Important! Before starting the journey, mount suitable winter tyres and have snow chains on board. Snow chains are prohibited on aluminium rims.
Winter camping 17.2 17 Winter operation Danger! Risk of suffocation Do not use any catalytic stoves or infrared radiators in the vehicle. The oxygen in the living area is then used. Caution! Risk of damage through freezing Do not store any fluids in the unheated vehicle when there is a risk of frost. If the vehicle is left with the heating switched off for a longer period of time at low temperatures, the water pipes and tanks could freeze and thus be damaged.
17 17.
Placing out of service 18 18 Placing out of service Important! When the instructions for maintenance and care, and the checklist for placing out of service are observed, the vehicle can be parked outdoors all year round. 18.1 Checklist for temporary placing out of service: Activity Bodywork Keep the forced ventilation and all mushroom ventilators open. Carefully wash the vehicle and apply a paint protection product (wax). Repair paintwork damage.
18 Placing out of service Activity Bacteria and algae can form in the water tank, therefore, after the end of the journey, the water tank must always be drained, thoroughly cleaned (Chapter 12.2) and allowed to dry. We recommend using a disinfectant for the water tank. Ask your ADRIA dealer for advice. Appliances Empty and clean the refrigerator; leave the refrigerator door and the freezer compartment, if applicable, open.
Placing out of service 18.2 18 Placing out of service over the winter The following measures are required in addition to those already mentioned for the temporary placing out of service over the winter. Activity Bodywork Clear snow from the roof when it snows. Thoroughly heat and ventilate the vehicle every four weeks. Lubricate all hinges and locks. Apply talc or Vaseline to all rubber seals. Use graphite dust to treat locking cylinders.
18 18.3 Placing out of service Returning to service after the placing out of service Perform the following activities for returning the vehicle to service. Activity Bodywork Remove tarpaulin and possibly wooden slats. If the vehicle has been stationary for a long period (approx. 10 months), have the brake system checked by an authorised workshop. Check the tyre pressure, also of the spare wheel (special equipment). Remove cover from the exhaust cowl, if present.
Cleaning & care 19 Cleaning & care 19.1 Cleaning and care - exterior 19 The polyester outer skin (glass-fibre reinforced plastic) of the vehicle was dyed at the factory, i.e. not painted. We recommend the following steps for the care of the vehicle: Warning! Risk of injury and damage to the vehicle roof The roof of the vehicle is not designed for the weight of standing persons. The roof of the vehicle is not capable of supporting walking persons. Do not walk on roof structures or roof fittings, e.g.
19 Cleaning & care The painted outer surface of the vehicle can be preserved with a commercially available wax. Pay attention to the manufacturer's instructions. Treat polyester parts every year with a two-component wax. Pay attention to the manufacturer's instructions. Observe the environmental protection measures in cleaning and care of the vehicle. 19.1.1 Cleaning the acrylic windows (side windows, roof hoods) Important! • Never drive the vehicle through a wash facility.
Cleaning & care 19 Very greasy or oily spots can be washed with ethyl, isopropyl or isobutyl alcohol. Organic solvents (e.g. acetone, methanol or ethanol) could damage the material. An example of possible damage to moulded plastic parts are stress cracks caused by different media. Other chemicals can have a swelling and softening effect on the plastic material. Therefore, plastic parts should be subjected to contact with the solvents referred to above only for a short period (2 minutes max.
19 19.2.3 Cleaning & care Care of cushions, curtains, net curtains Small spots in the cushions can be removed with commercially available cleaning foam for use on cushions or the foam of mild detergent. Do not wash cushions. Protect cushions from direct sunlight so that it does not fade. Have large spots or soiling removed by the dry cleaners. Have curtains and net curtains cleaned by the dry cleaners only.
Cleaning & care 19 19.2.5.3 Cleaning the oven Caution! Damage to seals and surfaces Do not allow the door seal to come into contact with oil or grease. Do not use scouring agents. These scratch the surfaces. Clean the inside and outside of the appliance before you place it into service and then at regular intervals. Use only soft cloths. Clean the appliance only with mild household cleaners. Then rinse the appliance with fresh water and dry thoroughly. 19.2.5.
19 19.2.6 Cleaning & care Cleaning the bathroom Caution! Damage to surfaces Do not clean the bathroom and the toilet with solvents or cleaning agent containing alcohol. Do not use scouring agents. – These could cause cracks or embrittlement of the plastic material. Do not pour caustic substances or boiling water into the drains. – These damage both the drain pipes and the siphon traps. Do not allow the door seal to come into contact with oil or grease. Do not use scouring agents.
Inspection & Maintenance 20 Inspection & Maintenance 20.1 Inspection work 20 Important! As with any vehicle, the caravan must be officially inspected at regular intervals (Chapter 2.4). Important! Use only original spare parts from the respective manufacturer. Inspection and maintenance work (Chapters 20.3 and 20.4) must be performed at regular intervals.
20 20.3 Inspection & Maintenance Chassis Maintenance activity Interval General inspection of caravan According to regulations in the country of registration Have the brake system checked in an authorised workshop Every year Have the undersealant checked Every year Check the tightening torque of wheel nuts Monthly Check tread depth and tyre pressure Before starting to drive Check the exterior lighting Before starting to drive Tab.
Inspection & Maintenance 20.5 20 Checking and replenishing operating fluids Operating fluids include: • Air-conditioning system cooling medium (special equipment) • Heater liquid for warm water heating (special equipment) Please see the manufacturer's original operating instructions for checking operating fluids. 20.5.1 Checking and replenishing the fluid level of the Alde warm water heater Important! • Avoid bubbles. • Always position the vehicle horizontal and level.
21 21 Troubleshooting Troubleshooting Please pay attention to the following information for finding and correcting faults. If you cannot remedy the faults yourself, contact the service of your competent ADRIA dealer or of the respective appliance manufacturer (heater = Truma, toilet = Thetford, etc.). Warning! Risk of injury and severe damage to the vehicle All repairs on the vehicle and on the brake system have to be performed in an authorised workshop only! 21.1 Changing wheels 21.1.
Troubleshooting 21 Before repair: Do not pull out any foreign objects (screws or nails) that have penetrated the tyre. Before repair, carefully check the tyre sidewall. Do not use the tyre mobility system when the tyre has already been damaged by driving with the flat tyre. Also check the rim. When the rim is damaged (deformation of the bead of the rim that causes loss of air), repair is not possible. After repair: Stop after driving for approx. 10 minutes and check the tyre pressure.
21 Troubleshooting 21.1.3.2 Changing the wheel Warning! Risk of injury when the vehicle rolls away Perform the wheel change only when the vehicle has been secured. Caution! Unsafe wheel attachment Always use the correct wheel bolts. For light-metal rims, different wheel bolts (diameter, length) can be used than for steel rims. Ensure the bolts are not interchanged. Secure the vehicle (Chapter 21.1.1). Uncouple the caravan and apply the handbrake.
Troubleshooting 21.1.4 21 Tightening the wheel nuts 1 Fig. 109 Rim 2 Wheel nuts or wheel bolts 1 4 3 2 1 2 5 Tightening the wheel nuts Tighten the wheel nuts or wheel bolts (Fig. 109/2) in the sequence 1 - 2 - 3 - 4 - 5. Check the firm seating of all wheel nuts or wheel bolts again. Use a torque wrench for light-metal rims without steel bushings. – 100 Nm for steel rims – 120 Nm for light-metal rims After driving approx. 50 km, check the seating of the wheel nuts or wheel bolts.
21 21.2 Troubleshooting Replacing lighting elements Caution! Damage to bulbs Never touch the new bulbs with your bare fingers. Always use a clean and lint-free cloth. Before starting to drive, check the function of all interior and exterior lighting equipment on the vehicle and replace defective lighting elements. 21.2.1 Changing bulbs - front The contour lights at the front are LED lights. The LED lights have a very long service life and seldom need to be replaced.
Troubleshooting 21.3 21 Bulb types for exterior lighting Refer to Chapter (Tab. 7) 10.7 for types and capacities of the exterior lights. 21.4 Water supply faults Fault Possible cause Remedy No water Water tank is empty. • Water leak in vehicle Tab. 17 21.5 Fuse of water pump defective. • Replace the defective fuse. "Water supply" switch on control panel switched off. • Switch the switch on. Water pump defective. • Have the water pump replaced in an authorised workshop.
21 21.6 Troubleshooting Gas system faults Fault Possible cause Measure Gas smell, Gas system leaks. • Immediately put the gas system out of service. • Close the gas cylinder shut-off valves. • Avoid any type of ignition spark and open light. • Ventilate the vehicle well (Chapter 2.5). • Repair by authorised workshop. Gas cylinder is empty. • Exchange gas cylinder (Chapter 11.5 and 11.6).
Troubleshooting 21.7 21 Alde Compact 3010 heater faults Important! Consult an authorised workshop if the listed measures are not successful. Fault Possible cause Heater does not start. See Chapter 21.6 "No gas". No supply voltage (12 V). Electrical operation (230 V) not possible. Tab. 20 21.8 • Check battery voltage (12 V). • Check all electric connectors and fuses. • Check the circuit breaker is switched on. • Check the 230 V plug is connected to the heater system.
21 21.9 Troubleshooting Refrigerator/freezer compartment faults Fault Possible cause No gas operation See (Chapter 21.12 "no gas"). No 230 V mode No 12 V mode Cooling function is not sufficient Tab. 22 158 GB Remedy Energy selector switch on refrigerator in false position. • Switch power selector switch on refrigerator to "Gas mode" or "Automatic mode" (Chapter 15.1). Air in gas pipe • Switch the appliance off and start again. Repeat three to four times.
Troubleshooting 21.10 Power supply faults Fault Possible cause Remedy Ground-fault circuit breaker triggered Fault in 230 V cables of vehicle. • Contact Customer Service. Fault in an electrical appliance. • Disconnect all electrical consumers until the ground-fault circuit breaker no longer triggers. • Have defective appliances repaired by a qualified electrician. • Switch on the circuit breaker in the vehicle. • Have the mains voltage checked. 12 V power supply unit defective.
21 21.11 Troubleshooting Control panel faults Fault Possible cause Remedy 12 V supply does not function 12 V main switch switched off • Switch 12 V main switch on (Chapter 10.2). Fuse defective. • Contact Customer Service. 12 V control indicator (green) is not lit 12 V supply switched off • Switch on the 12 V supply. System cannot be switched on Living area battery is not charged or insufficiently charged. • Charge the living area battery Fuse defective • Contact Customer Service.
Troubleshooting 21.12 Central lighting control malfunctions Fault Possible cause Remedy No lamps can be switched on No 12 V voltage available • Check fuse in 12 V power supply unit. • Check cable for breaks. • Check plug of 12 V power supply unit. • Check plug of light control unit. Fault on light control unit • Contact Customer Service. Lamp defective • Check lighting element Cable to lamp defective • Check cable for breaks. • Check cable for short-circuits.
22 Technical Data 22 Technical Data 22.1 Tyres / tyre pressure Tyre size bar psi Max. vehicle weight (single axle) 185/65 R14 86 2,7 39 1060 kg 195/70 R 14 91 2,7 39 1230 kg 185 R14 C 102 4,5 65 1700 kg 195 R14 C 106 4,5 65 1900 kg 195/70 R15 C 104 4,5 65 1800 kg Tab. 26 Tyres / tyre pressure For the tyre size, please see the vehicle documents or look at the tyres of your vehicle. 22.2 Additional load / weight 22.2.
Technical Data 22 22.2.2.1 Additional load Caution! Danger of overloading When the vehicle is overloaded, the insurance coverage and the warranty claim to the manufacturer become void. Do not exceed the gross weight rating entered in the vehicle documents. Important! • Load the vehicle properly (Chapter 5.4). • Weigh the vehicle before starting the journey (e.g. public vehicle scales). • The driving behaviour of an overloaded vehicle changes drastically. It can get out of control during the journey.
22 22.2.3 Technical Data Weight of additional equipment and accessories The additional equipment packages and accessories of the vehicle are listed with their weights here. Check the additional equipment used and enter into the total weights list (Chapter 22.2.4). All weight information is "approximate information". Additional equipment / accessories Weight (approx.
Technical Data 22.2.4 22 Weight of personal equipment and accessories Personal equipment / accessories Weight (approx.) Overall weight of personal equipment Tab.
22 22.3 Technical Data Awning A/A sizes and draught skirt sizes Important! • The dimension and weight information is within possible tolerances ± 5%. • The Tables show the body length for vehicles that may not be available in your country. 1 2 Fig. 110 1 Awning A/A size 2 Draught skirt size 10100010 Awning A/A size and draught skirt size Refer to the respective Table for the awning A/A sizes and draught skirt sizes 22.3.
Technical Data 22.3.3 ALTEA Vehicle type Awning A/A size [cm] Draught skirt size [cm] 390 849 407 432 882 440 462 920 478 472 935 493 512 964 522 532/542 990 548 562 1018 576 Tab. 31 22.3.4 Awning A/A size and draught skirt size ALTEA ADORA Tab.
22 22.3.5 Technical Data ALPINA Body length [cm] Awning A/A size [cm] Draught skirt size [cm] 563 1029 584 613 1078 633 663 1127 682 743 1211 766 763 1225 780 Tab. 33 22.3.6 ASTELLA/ASTELLA GLAM Body length [cm] Awning A/A size [cm] Draught skirt size [cm] 553/563 1010 568 613 1066 624 663 1127 682 Tab.
Checklists 23 23 Checklists Important! These lists also include special equipment and personal equipment not included in the standard caravan equipment. 23.1 Checklist caravan, general Checklist Caravan General inspection of caravan carried out (Chapter 2.4.1) Gas inspection carried out (Chapter 2.4.2) Maintenance and inspection work carried out (Chapter 20) Tyres not older than 6 years (only for 100 kmh approval) Wheel bolts, wheel nuts tightened correctly Tyre pressure checked (Chapter 22.
23 Checklists Checklist Caravan Additional cushion for making the bed All ladders safely stowed Antenna retracted and secured All liquids stored in leak-proof containers All objects in open storage areas stowed securely Refrigerator, freezer compartment and oven doors latched securely Sink board safely stowed Cabinets and drawers latched securely Bathroom door latched securely All beds and bed extensions latched securely All tables safely stowed All windows and roof hoods closed securely Awning light swit
Checklists 23.
23 23.3 Checklists Living and sleeping area checklist Equipment Equipment Copies of: Identity cards, passports, visa Copies of: Vaccination cards, allergy passes, emergency passes Copies of: Driving licence, international driving licence Copies of: Vehicle documents, green insurance card Telephone number of local bank (if the EC card gets stolen) Telephone number of credit card company (if the credit card gets stolen) Clothes, shoes Pyjamas Rainwear, winter clothes (hat, scarf, gloves, boots...
Checklists 23.
23 23.
Checklists 23.6 23 Personal checklist Please copy and complete. Route: Date: Personal checklist Tab.
Index Index 0-9 12 V mode, refrigerator . . . . . . . . . . 73, 122 12 V power supply Battery selector switch . . . . . . . . . . . . 75 12 V power supply unit . . . . . . . . . . . . . . . 46 230 V mode, refrigerator . . . . . . . . . . . . 123 230 V power supply . . . . . . . . . . . . . . . . . 68 A Accessories Weights . . . . . . . . . . . . . . . . . . . . . . 164 Additional equipment Weights . . . . . . . . . . . . . . . . . . . . . . 164 Additional load . . . . . . . . . . . . . . . . . . . .
Index Control panel . . . . . . . . . . . . . . . . . . . . . 46 LT 413 . . . . . . . . . . . . . . . . . . . . . . . . 46 See control panel . . . . . . . . . . . . . . . 46 Type EN . . . . . . . . . . . . . . . . . . . . . . 47 Cooking . . . . . . . . . . . . . . . . . . . . . . . . . 112 Extractor hood . . . . . . . . . . . . . . . . . 114 Gas stove . . . . . . . . . . . . . . . . . . . . 116 Microwave oven . . . . . . . . . . . . . . . 115 Corner steadies . . . . . . . . . . . . . . . . . . .
Index K Keys Spare keys . . . . . . . . . . . . . . . . . . . . . 23 L Light bulbs, exterior lighting . . . . . . . . . . 154 Lighting control Central . . . . . . . . . . . . . . . . . . . . . . . . 48 Lighting, exterior . . . . . . . . . . . . . . . . . . . 154 Lights Lighting control . . . . . . . . . . . . . . . . . . 48 Outside . . . . . . . . . . . . . . . . . . . . . . . 155 Liquid gas . . . . . . . . . . . . . . . . . . . . . . . . . 91 Living area battery . . . . . . . . . . . . . . . . . .
Index Spare keys . . . . . . . . . . . . . . . . . . . . . . . 23 Step Electrical . . . . . . . . . . . . . . . . . . . . . . 27 T Table Lowering . . . . . . . . . . . . . . . . . . . . . . 65 Tank Waste water . . . . . . . . . . . . . . . . . . . 98 Water tank . . . . . . . . . . . . . . . . . . . . . 96 Technical data . . . . . . . . . . . . . . . . . . . 162 Tightening the wheel nuts . . . . . . . . . . . 153 Toilet . . . . . . . . . . . . . . . . . . . . . . . . . . . 125 Troubleshooting . . . . . . .
