User Manual

ManualsBrandsADOP ADVANCED OPTICAL TECHNOLOGY ManualsComputers & AccessoriesSFP+ to RJ45 Copper Module - 10GBase-T Plus Transceiver for Cisco SFP-10G-T-S, Ubiquiti, Netgear, Supermicro, QNAP, Broadcom, MikroTik S+RJ10, Avago, up to 30m

ADOP 10GBASE-T Copper SFP+ Transceiver

SFP-10GE-T

1.PRODUCT FEATURES



Support 10Gbase-T / 5Gbase-T / 2.5Gbase-T / 1000base-T



Hot-pluggable SFP footprint

 Compact RJ-45 connector assembly

 RoHS compliant and lead-free



Single +3.3V power supply

 10 Gigabit Ethernet over Cat 6a cable

 Ambient Operating temperature: 0°C to +65°C

2.PRODUCT DESCRIPTION

SFP-10GE-T Copper Small Form Pluggable (SFP) transceivers are based on the SFP

Multi Source Agreement (MSA) . They are compatible with the 10Gbase-T / 5Gbase-T /

Summary of content (9 pages)

PAGE 1
ADOP 10GBASE-T Copper SFP+ Transceiver SFP-10GE-T 1.PRODUCT FEATURES  Support 10Gbase-T / 5Gbase-T / 2.5Gbase-T / 1000base-T  Hot-pluggable SFP footprint  Compact RJ-45 connector assembly  RoHS compliant and lead-free  Single +3.3V power supply  10 Gigabit Ethernet over Cat 6a cable  Ambient Operating temperature: 0°C to +65°C 2.PRODUCT DESCRIPTION SFP-10GE-T Copper Small Form Pluggable (SFP) transceivers are based on the SFP Multi Source Agreement (MSA) .
PAGE 2
.5Gbase-T / 1000base-T standards as specified in IEEE Std 802.3 . SFP-10GE-T uses the SFP's RX_LOS(must be pulled up on host) pin for link indication. If pull up or open SFP's TX_DISABLE pin, PHY IC be reset. 3. Cable Length Standard 10Gbase-T 5Gbase-T/2.5Gbase-t 1000base-T Cable CAT6A CAT5E CAT5E Reach 30m 50m 100m Host Port XFI 5GBase-R/2.5GBase-X 1000base-FX 4.
PAGE 3
17 VEET Transmitter Ground 18 TD+ Transmitter Non-Inverted DATA in. AC Coupled. 19 TD- Transmitter Inverted DATA in. 20 VEET Transmitter Ground (Common with Receiver Ground) 1 AC Coupled. (Common with Receiver Ground) 1 Notes: 1. Circuit ground is connected to chassis ground 2. PHY disabled on TDIS > 2.0V or open, enabled on TDIS < 0.8V 3. Should be pulled up with 4.7k - 10k Ohms on host board to a voltage between 2.0 V and 3.6 V.
PAGE 4
5. +3.3V Volt Electrical Power Interface The SFP-10GE-T has an input voltage range of 3.3 V +/- 5%. The 4V maximum voltage is not allowed for continuous operation. Parameter Symbol +3.3 Volt Electrical Power Interface Min Typ Max Supply Current Is 700 900 mA Input Voltage Vcc 3.3 3.47 V Maximum Voltage Vmax Surge Current Isurge 3.13 4 TBD unit Notes/Conditions 3.0W max power over full range of voltage and temperature.
PAGE 5
7.High-Speed Electrical Interface All high-speed signals are AC-coupled internally. Parameter High-Speed Electrical Interface, Transmission Line-SFP Symbol Min Typ Max unit Notes/Conditions 5-level encoding, per IEEE 802.
PAGE 6
Addr Field Size (Bytes) Name of Field HEX Description 0 1 Identifier 03 SFP 1 1 Ext. Identifier 04 MOD4 2 1 Connector 22 RJ45 8 Transceiver 3-10 00 00 00 00 00 00 00 00 Transmitter Code 11 1 Encoding 06 64B66B 12 1 BR, nominal 67 10000M bps 13 1 Reserved 00 14 1 Length (9um)-km 00 15 1 Length (9um) 00 16 1 Length (50um) 00 17 1 Length (62.
PAGE 7
10. EEPROM INFORMATION（A2）, optional 11.
PAGE 8
Automatic crossover detection is enabled. Parameter Operating Temperature Storage Temperature Symbol Environmental Specifications Min Typ Max Top Tsto External crossover cable is not required unit Notes/Conditions 0 65 °C Case temperature -40 85 °C Ambient temperature 12. Serial Communication Protocol All ADOP SFPs support the 2-wire serial communication protocol outlined in the SFP MSA. These SFPs use an MCU, can be accessed with address of A0h.
PAGE 9
14.