NuPRO-E42 Full-Size PICMG 1.3 Intel® Core™ i7/i5/i3 LGA 1150 SHB User’s Manual Manual Rev.: 2.50 Revision Date: Apr. 24, 2015 Part No: 50-13073-1010 Advance Technologies; Automate the World.
Revision History ii Revision Release Date Description of Change(s) 1.00 2013/11/26 Preliminary release 2.
NuPRO-E42 Preface Copyright 2015 ADLINK Technology, Inc. This document contains proprietary information protected by copyright. All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic, or other means in any form without prior written permission of the manufacturer.
Conventions Take note of the following conventions used throughout this manual to make sure that users perform certain tasks and instructions properly. Additional information, aids, and tips that help users perform tasks. NOTE: CAUTION: WARNING: iv Information to prevent minor physical injury, component damage, data loss, and/or program corruption when trying to complete a task.
NuPRO-E42 Table of Contents Revision History...................................................................... ii Preface .................................................................................... iii List of Figures ........................................................................ ix List of Tables.......................................................................... xi 1 Introduction ........................................................................ 1 1.1 Overview.........
2.4.4 Management Engine................................................. 29 2.4.5 USB 3.0 Driver.......................................................... 29 A Appendix: BIOS Setup.......................................................31 A.1 Starting the BIOS ............................................................... 31 A.2 Main Setup......................................................................... 35 A.3 Advanced BIOS Setup .......................................................
NuPRO-E42 C.4 Interrupt Request (IRQ) Lines............................................ 71 Important Safety Instructions .............................................. 77 Getting Service......................................................................
This page intentionally left blank.
NuPRO-E42 List of Figures Figure 1-1: Figure 1-2: Figure 1-3: Figure 1-4: NuPRO-E42 Block Diagram ............................................ 4 NuPRO-E42 Board Dimensions ...................................... 7 Rear Panel I/O Ports........................................................ 8 Connectors and Jumpers...............................................
This page intentionally left blank.
NuPRO-E42 List of Tables Table Table Table Table Table Table Table Table Table Table Table 1-1: 1-2: 1-3: 1-4: C-1: C-2: C-3: C-4: C-5: C-6: C-7: List of Tables NuPRO-E42 General Specifications................................ 3 NuPRO-E42 I/O Connectivity .......................................... 8 Core™ i7-4770S Processor Power Consumption ......... 19 Core™ i5-4430S Processor Power Consumption ......... 20 System Memory Map.....................................................
This page intentionally left blank.
NuPRO-E42 1 Introduction 1.1 Overview The ADLINK NuPRO-E42 is a PICMG 1.3 System Host Board (SHB) supporting the 4th Generation Intel® Core™ i7/i5/i3 and Pentium® processors in LGA1150 package to deliver a scalable high performance platform for a wide array of industrial applications. The NuPRO-E42 supports 22nm process CPUs at up to 3.5 GHz with integrated graphics and memory controllers, Direct Media Interface (DMI) and Flexible Display Interface (FDI) connectivity to the Intel® Q87 Express Chipset.
To purchase the optional DB-Audio2 daughter board, please contact your ADLINK sales representative. NOTE: 1.3 Specifications System CPU • • • • Intel® Core™ i7-4770S, 3.1 GHz, 8M Cache, 65W TDP (4C) Intel® Core™ i5-4570S, 2.9 GHz, 6M Cache, 65W TDP (4C) Intel® Core™ i3-4330S, 3.5 GHz, 3M Cache, 54W TDP (2C) Intel® Pentium® G3420, 3.
NuPRO-E42 • • • • I/O Ports PCIe/PCI • • • • • 6x USB 3.0 ports (2x on rear panel, 4x on SHB) 4x USB 2.0 on backplane 4x SATA 6 Gb/s on SHB 6x serial ports via onboard pin-header (5x RS-232, 1x RS-232/422/485 with auto flow control) 2x Gigabit Ethernet RJ45 ports 1x VGA port (Dsub-15) 1x DVI-D via onboard pin-header (opt. cable bracket) Pin header for HD Audio DB-Audio2 daughter board 1x PS/2 KB/MS via onboard pin header (opt.
1.4 Block Diagram Figure 1-1: NuPRO-E42 Block Diagram 1.5 Functional Description Processor Support The NuPRO-E42 is PICMG 1.3 System Host Board supporting the 4th Generation Intel® Core™ processor family (Intel® Core™ i7/i5/i3) in LGA1150 socket. An integrated memory controller supports dual channel DDR3 and Intel® HD Graphics is integrated onboard the CPU. The CPU provides a PCI Express x16 for external graphics or expansion.
NuPRO-E42 tion. Direct Media Interface (DMI) is the chip-to-chip connection between the processor and PCH. Intel® Flexible Display Interface carries display traffic from the integrated graphics in the processor to the legacy display connectors in the PCH. The PCH supports all other required interfaces including PCI Express, SATA 6 Gb/s, USB 3.0, PCI, LPC, and SPI.
timely failure detection, and ensure stable supply of current for critical components. Watchdog Timer The watchdog timer (WDT) monitors system operations based on user-defined configurations. The WDT can be programmed for different time-out periods, such as from 1 to 255 seconds or from 1 to 255 minutes. The WDT generates a reset signal, then a reset request, after failure to strobe it within the programmed time period. A register bit may be enabled to indicate if the watchdog timer caused the reset event.
NuPRO-E42 1.6 Mechanical Drawing 117 111 38.5 6 6.5 146 338.1 333.6 4.92 20.59 123.
1.7 I/O Connectivity I/O Bracket Onboard Golden Finger Remarks VGA Y — — DB-15 DVI-D — Y — cable w/ bracket optional LAN1/2 (RJ-45) Y — — Act/Link/ Speed LEDs — Y — cable w/ bracket optional 2 — — USB 3.0 — 4 — cable w/ bracket optional USB backplane — — 4 COM1-2 — Y — USB 2.0 2.54” pitch COM3-6 — Y — 2.00" pitch PS/2 KB/MS USB Rear Panel USB 3.
NuPRO-E42 Connector 3 VGA port 4 USB 3.0 ports Description DB-15 connector for CRT or LCD monitor SuperSpeed USB 3.0 ports USB 3.0 Connectors Pin # Signal Name 1 USB3.
On Linked Green 100 Mb connection Blinking Data Activity Amber 1 Gb connection VGA Port 10 Pin # Signal Pin # Signal 1 Red 9 +5 V 2 Green 10 Ground 3 Blue 11 NC 4 NC 12 DDC DAT 5 Ground 13 HSYNC 6 Ground 14 VSYNC 7 Ground 15 DDC CLK 8 Ground Introduction
NuPRO-E42 1.
1.10 Onboard Connectors COM1~6 Connector (RS-232) (CN11~14/16/23) 1 Pin # RS-232 Signal 1 DCD 2 DSR 3 RXD 4 RTS 5 TXD 6 CTS 7 DTR 8 RI 9 GND 10 NC 2 9 10 COM1 COM2 COM3 COM4 COM5 COM6 Connector CN23 CN16 CN11 CN12 CN13 CN14 Pitch 2.54 mm 2.54 mm 2.00 mm 2.00 mm 2.00 mm 2.
NuPRO-E42 USB 3.
DVI-D Bracket Connector (optional cable w/ bracket, P/N 30-01052-2000) Pin # Signal Pin # Signal 1 TMDS Data2- 13 TMDS Data3+ 2 TMDS Data2+ 14 +5 V Power 3 TMDS Data2/4 Shield 15 GND 4 TMDS Data4- 16 Hot Plug Detect 5 TMDS Data4+ 17 TMDS Data0- 6 DDC Clock [SCL] 18 TMDSData0+ 7 DDC Data [SDA] 19 TMDS Data0/5 Shield 8 Analog vertical sync 20 TMDS Data5- 9 TMDS Data121 TMDS Data5+ This page TMDS Data1+intentionally 22 left blank.
NuPRO-E42 PS/2 Keyboard/Mouse Pin Header (CN27) 1 2 Pin # Signal Pin # Signal 1 KBDATA 2 KBCLK 3 MSDATA 4 MSCLK 5 KM_VCC 6 GND Serial ATA Connectors (CN30~33) 1 7 Pin # Signal 1 2 3 4 5 6 7 GND TXP TXN GND RXN RXP GND HD Audio Daughter Board Connector (CN40) This connector is designed for use with the ADLINK DB-Audio2 daughter board.
System Panel Connector (CN45) Connects to chassis-mounted buttons, speakers, and LEDs. Pin # 1 11 10 20 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Signal Function Pin Group WDSPK Speaker signal NC Chassis Speaker NC +5V Power NC GND Ground Key Lock KEYLOCK Keyboard lock PLED Power LED signal Power LED NC +5V Power LED pull-up GND Ground Reset Button RESETBT RESET signal NC GND Ground Power Button POWERBT Power-on signal NC NC HDDLED Hard Disk LED signal HDD LED +3.
NuPRO-E42 1.11 Jumpers & Switches Clear CMOS Jumper (JBAT1) To clear the BIOS settings (RTCRTS# asserts): 1. Power down and disconnect power from the system. 2. Short pins 2-3 on JP1. 3. Reconnect power and power up the system. 4. Wait 3 seconds or more. 5. Power down and disconnect power from the system. 6. Re-short pins 1-2, and power up the system..
COM1 Mode Switch (SW13) ON ON 11 22 3 DIP #1 DIP #2 COM1 Mode On Off RS-232 On On RS-422 Off On RS-485 1.12 Power Consumption Intel® Core™ i7-4770S, 3.1 GHz, 8M Cache, 65W TDP (4C) Test Configuration Memory Transcend TS1GLK64V6H DDR3-1600 8GB x2 Graphics Integrated Intel® HD Graphics SATA Channel 1 ALDINK ASD26-MLC32G-CT Power Supply FSP FSP350-60PFG 350W BIOS Rev. 0.91 Mode Power (W) Total (W) 0.86A / 12V 10.32 0.43A / 5V 2.15 0.78A / 3.3V 2.574 S3 129mA / 5VSB 0.645 0.
NuPRO-E42 Current (A) / Voltage (V) Mode Power (W) Total (W) 0.38A / 12V Idle Load CPU Max Max. Load 4.56 0.68A / 5V 3.4 0.78A / 3.3V 2.574 6.53A / 12V 78.36 0.85A / 5V 4.25 0.77A / 3.3V 2.541 6.50A / 12V 78 1.15A / 5V 5.75 0.78A / 3.3V 2.574 10.534 85.151 86.324 Table 1-3: Core™ i7-4770S Processor Power Consumption Intel® Core™ i5-4330S, 2.
Mode Current (A) / Voltage (V) 3.61A / 12V CPU Max Max. Load Power (W) Total (W) 43.32 0.81A / 5V 4.05 0.66A / 3.3V 2.178 3.80A / 12V 45.6 1.33A / 5V 6.65 0.65A / 3.3V 2.145 49.548 54.395 Table 1-4: Core™ i5-4430S Processor Power Consumption 1.13 Package Contents Before unpacking, check the shipping carton for any damage. If the shipping carton and/or contents are damaged, inform your dealer immediately. Retain the shipping carton and packing materials for inspection.
NuPRO-E42 2 Getting Started 2.1 Installing the CPU The NuPRO-E42 supports an Intel® Core™ i7/i5/i3 or Pentium® processor in an LGA1150 socket. X Disconnect all power to the board before WARNING: installing a CPU to prevent damaging the board and CPU. X Do not touch socket contacts. Damaging the contacts voids the product warranty. Follow the installation instructions carefully to avoid damaging the board components. To install the CPU: 1.
3. Lift the load plate to uncover the socket. 4. Remove the plastic protective cover from the socket. Note the locations of the alignment keys (A) and Pin 1 indicator (B). B A Do NOT touch socket contacts. WARNING: 5. Hold the CPU using thumb and forefinger as shown. Position the CPU over the socket, matching the notches on the sides of the CPU with the alignment keys on the socket (A).
NuPRO-E42 cator as shown (B). B A The CPU fits into the socket in only one orientation. DO NOT force it into the socket to avoid causing damage. WARNING: 6. Carefully place the CPU into the socket vertically. The socket has cutouts for your fingers to fit into.
7. Gently lower the load plate. Make sure the front edge of the plate is under the screw as indicated. 8. Lower the locking arm and fasten it to the retention tab (A). The load plate should be locked underneath the screw as shown (B).
NuPRO-E42 2.2 Installing the CPU Fan and Heatsink WARNING: The CPU requires a chassis with an airflow inlet and maximum internal ambient temperature of 50° C. A especially-designed CPU fan and heatsink must be installed before using the SHB. Failure to install a CPU fan and heatsink may damage the system host board and/or the CPU.. If CPU fan installation procedures presented here are inconsistent with the installation procedures you obtained from the CPU fan and heatsink package, follow the latter.
Memory Configuration Options The NuPRO-E42 supports 1GB, 2GB, 4GB and 8GB unbuffered non-ECC DDR3 DIMMs in the following configurations: X Channel A: DIMM1 Channel B: DIMM2 X For dual-channel configuration, the total size of memory module installed per channel must be the same (DIMM1 = DIMM2). X It is recommended that you install DIMMs with the same CAS latency. For maximum compatibility, install memory modules with the same brand, model, and/or rating. To install a memory module: 1.
NuPRO-E42 Notch Break 4. Insert the module firmly into the slot until the retaining clips snap back inwards and the module is securely seated. 2.4 Driver Installation This chapter provides information on how to install the NuPROE42 device drivers under Windows 7 64-bit.
Management Engine \NuPRO\NuPRO-E42\Others\ME_Driver\ Install the Windows operating system before installing any driver. Most standard I/O device drivers are installed during Windows installation. WARNING: 2.4.1 In order to enable RAID or AHCI mode, you must pre-install the Intel® Rapid Storage Technology driver during the Windows* installation process. using the F6 installation method. *Not required for Windows Vista and Windows 7.
NuPRO-E42 and follow the onscreen instructions. Restart the system if prompted. 2.4.4 Management Engine Follow these instructions to install the Management Engine driver. 1. Locate the directory X:\NuPRO\NuPRO-E42\Others\ME_Driver\ on the ADLINK All-in-One DVD, and extract all files from the following archive: ME90.zip. 2. Run the program setup.exe and follow the onscreen instructions. Restart the system if prompted. 2.4.5 USB 3.0 Driver Follow these instructions to install the USB 3.0 driver. 1.
This page intentionally left blank.
NuPRO-E42 Appendix A BIOS Setup The following chapter describes basic navigation for the AMIBIOS® EFI BIOS setup utility. A.1 Starting the BIOS To enter the setup screen, follow these steps: 1. Power on the motherboard 2. Press the < Delete > key on your keyboard when you see the following text prompt: < Press DEL to run Setup > 3. After you press the < Delete > key, the main BIOS setup menu displays. You can access the other setup screens from the main BIOS setup menu, such as Chipset and Power menus.
in the left frame, it is highlighted in white. Often a text message will accompany it. Navigation The BIOS setup/utility uses a key-based navigation system called hot keys. Most of the BIOS setup utility hot keys can be used at any time during the setup navigation process. These keys include < F1 >, < F10 >, < Enter >, < ESC >, < Arrow > keys, and so on. .
NuPRO-E42 Note: There is a hot key legend located in the right frame on most setup screens. There is a hot key legend located in the right frame on most setup screens.. NOTE: The < F8 > key on your keyboard is the Fail-Safe key. It is not displayed on the key legend by default. To set the Fail-Safe settings of the BIOS, press the < F8 > key on your keyboard. It is located on the upper row of a standard 101 keyboard.
F10 The < F10 > key allows you to save any changes you have made and exit Setup. Press the < F10 > key to save your changes. The following screen will appear: Press the < Enter > key to save the configuration and exit. You can also use the < Arrow > key to select Cancel and then press the < Enter > key to abort this function and return to the previous screen. ESC The < Esc > key allows you to discard any changes you have made and exit the Setup.
NuPRO-E42 A.2 Main Setup When you first enter the Setup Utility, you will enter the Main setup screen. You can always return to the Main setup screen by selecting the Main tab. There are two Main Setup options. They are described in this section. The Main BIOS Setup screen is shown below. System & Board Info BIOS Vendor Displays the BIOS vendor. Core Version Displays the BIOS core version. Compliancy Displays the current BIOS compliancy. Project Version Displays the current BIOS revision.
System Time/System Date Use this option to change the system time and date. Highlight System Time or System Date using the < Arrow > keys. Enter new values using the keyboard. Press the < Tab > key or the < Arrow > keys to move between fields. The date must be entered in MM/ DD/YY format. The time is entered in HH:MM:SS format. Note: The time is in 24-hour format. For example, 5:30 A.M. appears as 05:30:00, and 5:30 P.M. as 17:30:00. Access Level Displays the current system access level. A.
NuPRO-E42 Launch PXE OpROM Boot Option for Legacy Network Devices. Options: Enabled/ Disabled. A.3.1 ACPI Settings Enable APIC Auto Configuration BIOS ACPI Auto Configuration. Options: Enabled/Disabled. Enable Hibernation Enable or disable the system's ability to hibernate (S4 sleep state). This option may be not effective with some OS's. ACPI Sleep State Select the highest ACPI sleep state the system will enter, when the SUSPEND button is pressed. Options: S1, S3, Suspend Disable.
A.3.2 Trusted Computing Trusted computing is an industry standard to make personal computers more secure through a dedicated hardware chip, called a Trusted Platform Module (TPM). TPM Support This option enables or disables the TPM support. System reset is required. Options: Enabled/Disabled. TPM State Determine whether TPM state change requires Password Authentication. Options: Enabled/Disabled. Pending TPM Operation Scheduled TPM operation. The settings for this value are Enable, Disable and Clear.
NuPRO-E42 A.3.3 CPU Configuration Active Processor Cores Number of cores to enable in processor. Options: All, 1, 2. Limit CPUID Value Maximum When Enabled, the processor will limit the maximum CPUID input value to 03h when queried, even if the processor supports a higher CPUID input value. When Disabled, the processor will return the actual maximum CPUID input value of the processor when queried. Enable this option to allow compatibility with older operating systems.
tems to software. This allows for multiple, independent operating systems to be running simultaneously on a single system. Power Technology Sets the power management features. Options: Disable, Energy Efficient, Custom.
NuPRO-E42 Socket 0 CPU Information A.3.
SATA Mode Options: IDE, RAID, AHCI. Serial ATA Controller 0/1 Appears when SATA mode is set to IDE. This item specifies whether Serial ATA Controller 0/1 is initialized in Compatible or Enhanced mode of operation. The settings are Disabled, Compatible and Enhanced. Aggressive Link Power Management Appears when SATA mode is set to AHCI. The settings are Disabled and Enabled. SATA Port 0~5 The Staggered Spin-up, External SATA Port (eSATA) and Hot Plug options appear when SATA Mode is set to AHCI.
NuPRO-E42 Extensions (SMX), and Intel® Virtualization Technology (Intel® VT) and Intel® Virtualization Technology for Directed I/O (VT-d) are enabled. A.3.6 Intel IGD SWSCI OpRegion DVMT Mode This item allows the user to enable or disable the DVMT function. DVMT/Fixed Memory Select DVMT/Fixed memory size used by the Integrated Graphics Device. Options: 128MB, 256MB, Maximum. IGD - Boot Type Select the video device which will be activated during POST.
A.3.7 USB Configuration Legacy USB Support Legacy USB Support refers to USB mouse and keyboard support. Normally if this option is not enabled, any attached USB mouse or USB keyboard will not become available until a USB compatible operating system is fully booted with all USB drivers loaded. When this option is enabled, any attached USB mouse or USB keyboard can control the system even when there are no USB drivers loaded on the system. Set this value to enable or disable the Legacy USB Support.
NuPRO-E42 XHCI Hand-Off This is a workaround for OSes without XHCI hand-off support. The XHCI ownership change should be claimed by XHCI driver. Options: Enable, Disable. EHCI Hand-Off This is a workaround for OSes without EHCI hand-off support. The EHCI ownership change should be claimed by EHCI driver. Options: Enable, Disable. All USB Devices Enabled/Disabled All USB devices. Options: Enable, Disable. EHCI Controller 1/2 Enabled/Disabled USB 2.0 (EHCI) Support. Options: Enable, Disable.
A.3.8 Super IO Configuration Serial Port1-6 Configuration Enter the submenu for each serial port to enable/disable and view the I/O port and IRQ settings. Parallel Port Configuration Enter the submenu to enable/disable the parallel port and specify the base I/O port address.
NuPRO-E42 A.3.9 Hardware Monitor You can use this screen to view System Status information and to select options for FAN1 settings (FAN2 is set to Full On by default). Smart Fan 1 Mode Setting Three operating modes are provided for FAN1: Full Mode, Automatic Mode, and Manual Mode. Full Mode runs the fan at full speed. Automatic Mode is Smart Fan mode. Manual Mode runs the fan at the set speed (minimum is 0, maximum is 127). Automatic Mode In Automatic Mode, the following settings are visible.
When the temperature in degrees (°C) is higher than the set value, FAN1 will increase its speed according to the PWM Slope Setting value. Fan Start PWM Sets the PWM value of the fan between Fan Off Temperature Limit and Fan Start Temperature Limit. Minimum value is 0 and maximum is 127. PWMSlope Setting The Slope PWM Value sets the rate of increase the fan speed when the temperature is above Fan Start Temperature Limit. System Status System temperature, CPU temperature and fan speed (FAN1), system voltages.
NuPRO-E42 Unconfigure AMT/ME This item allows the user to unprovision the AMT/ME function without a password. WatchDog Timer Options: Enabled/Disabled. OS WatchDog Timer Sets the OS WatchDog Timer (seconds). BIOS WatchDog Timer Sets the BIOS WatchDog Timer (seconds). A.3.11 Serial Port Console Redirection COM0/1 Console Redirection Options: Enabled/Disabled.
Console Redirection Settings The settings specify how the host computer and the remote computer exchange data. Both computers should have the same or compatible settings. Terminal Type This option is used to select either VT100/VT-UTF8 or ANSI terminal type. Options: VT100, VT100+, VT-UTF8, ANSI. Bits per second Select the bits per second you want the serial port to use for console redirection. The options are 115200, 57600, 38400, 19200, 9600.
NuPRO-E42 Flow Control Set this option to select Flow Control for console redirection. The settings for this value are None, Hardware RTS/CTS. Record Mode With this mode enabled only text will be sent., allowing capture of Terminal data. Set this value to Enabled or Disabled. Resolution 100x31 Enable or disable extended terminal resolution. Set this value to Enabled or Disabled. Legacy OS Redirection Resolution On a legacy OS, the number of Rows and Columns supported by redirection.
Windows servers, even when a server is not connected to the network or the network is not available Terminal Type VT-UTF8 is the preferred terminal type for out-of-band management. The next best choice is VT100+ and then VT100. See above, in Console Redirection Settings page, for more Help with Terminal Type/Emulation. Options: VT100, VT100+, VT-UTF8, ASNI. Bits per second Select the bits per second you want the serial port to use for console redirection. The options are 115200, 57600, 38400, 19200, 9600.
NuPRO-E42 Parity Displays the parity for Out-of-Band Management. Stop Bits Displays the number of stop bits for Out-of-Band Management. A.4 Chipset Setup Select the Chipset tab from the setup screen to enter the Chipset BIOS Setup screen. You can select any of the items in the left frame of the screen to go to the sub menu for that item. The Chipset BIOS Setup screen is shown below.
A.4.1 Graphics and Memory Bridge Configuration VT-d Intel Virtualization Technology for Directed I/O. Options: Enabled/ Disabled. Initial Graphics Adapter Allows you to select which graphics controller to use as the primary boot device. Options: IGD, PCI/IGD, PCI/PEG, PEG/IGD, PEG/PCI. IGD Memory IGD shared memory size, Options: Disable/32M/64M/128M. IGD Multi-Monitor Multi-monitor support by the Internal Graphics Device.
NuPRO-E42 A.4.2 PCH Bridge Configuration 82574L LAN Controller Controls the onboard Intel 82574L LAN controller. Options: Enabled/Disabled. Restore on AC Power Loss Determines which state the computer enters when AC power is restored after a power loss. The options for this value are Last State, Power On and Power Off. X Power Off: Set this value to always power off the system while AC power is restored. X Power On: Set this value to always power on the system while AC power is restored.
PCI Express Port Configuration PCI Express Port 1~8 Configures the PCI Express ports in of the chipset. Options: Auto, Enable, Disable. PCIe Sub Decode Enable or disable the PCIe Sub Decode port. This option is available when the Subtractive Decode Agent is enable (PCHTrap9[14]) = '1b'. PCIE Ports 0-3 Configuration Use this option to configure PCIe ports 0-3 of the PCH to "One x4 Port" or "Four x1 Ports". The PCIE Ports 0-3 Configuration option is available in BIOS version A1.6 and later.
NuPRO-E42 A.4.3 Management Engine Subsystem ME Subsystem Options: Enabled/Disabled. ME Temporary Disable Options: Enabled/Disabled (reset required). End of POST Message Options: Enabled/Disabled. Execute MEBx Options: Enabled/Disabled. MEBx Mode Options: Normal, Hidden Ctrl+P, Enter MEBx setup.
Integrated Clock Chip Configuration ICC Enable Integrated Clock Chip. Options: Enabled/Disabled. A.5 Boot Configuration Select the Boot tab from the setup screen to enter the Boot BIOS Setup screen. You can select any of the items in the left frame of the screen, such as Boot Device Priority, to go to the sub menu for that item.
NuPRO-E42 ing it using the < Arrow > keys. The Boot Configuration screen is shown below: Setup Prompt Timeout Number of seconds to wait for setup activation. 65535 (0xFFFF) means wait indefinitely. Bootup NumLock State This setting determines the state of the NumLock function on bootup. Options: On, Off. Quiet Boot When this feature is enabled, the BIOS will display the fullscreen logo during the boot-up sequence, hiding normal POST messages.
Boot Option Priorities Set the boot device options to determine the sequence in which the computer checks which device to boot from. Hard Drive BBS Priorities The Boot devices are listed in groups by device type. First press to enter the sub-menu. You may then use the arrow keys to select the desired device, then press <+>, <-> or , key to move it up/down in the priority list. For example, USB storage disks will be listed as "USB Drives" in the sub-menu.
NuPRO-E42 cuted, using either or either the Supervisor password or User password. The Supervisor and User passwords activate two different levels of password security. If you select password support, you are prompted for a one to six character password. Type the password on the keyboard. The password does not appear on the screen when typed. Make sure you write it down. If you forget it, you must drain NVRAM and re-configure.
lighting it using the < Arrow > keys. The Exit BIOS Setup screen is shown below. Save Changes and Exit When you have completed the system configuration changes, select this option to leave Setup and reboot the computer so the new system configuration parameters can take effect. Save Configuration Changes and Exit Now? [Ok] [Cancel] appears in the window. Select Ok to save changes and exit.
NuPRO-E42 Discard Changes and Exit Select this option to quit Setup without making any permanent changes to the system configuration. Discard Changes and Exit Setup Now? [Ok] [Cancel] appears in the window. Select Ok to discard changes and exit. Save Changes and Reset Reset the system after saving the changes. Discard Changes and Reset Reset system setup without saving any changes. Save Changes Save changes made so far to any of the setup options.
the current boot order. If you are booting to the EFI Shell, an exit from the shell returns to Setup.
NuPRO-E42 Appendix B - Watchdog Timer A sample program for configuring the NuPRO-E42’s watchdog timer is included on the ADLINK All-in-One DVD in the following directory: \NuPRO\NuPRO-E42\WDT. B.1 Sample Code #include #include
} void Get_IT8783_ID(unsigned int &ID1, unsigned int &ID2) { outportb(IT8783_ioPort, 0x20); ID1 = inportb(IT8783_ioPort+1); outportb(IT8783_ioPort, 0x21); ID2 = inportb(IT8783_ioPort+1); } void IT8783_WDTRun(unsigned int count_value, unsigned int PLEDflag) //for NuPRO-E42 { unsigned long tempCount; unsigned int registerValue; outportb(IT8783_ioPort, 0x07); outportb(IT8783_ioPort+1, 0x07);// Device 7 outportb(IT8783_ioPort, 0xf8); outportb(IT8783_ioPort+1, 0x00);// PLED mapping to nothing, disable PLED fun
NuPRO-E42 outportb(IT8783_ioPort, 0xf8); outportb(IT8783_ioPort+1, 0x1f);// PLED mapping to GP37 outportb(IT8783_ioPort, 0xf9); registerValue = inportb(IT8783_ioPort + 1); registerValue |= 0x02; registerValue &= 0xfb; outportb(IT8783_ioPort+1, registerValue); } outportb(IT8783_ioPort, 0x71); registerValue = inportb(IT8783_ioPort + 1); registerValue &= 0xfe; outportb(IT8783_ioPort+1, registerValue); outportb(IT8783_ioPort, 0x72); registerValue = inportb(IT8783_ioPort + 1); registerValue &= 0xdf; outportb(IT
registerValue = inportb(IT8783_ioPort+1); registerValue |= 0x80; tempCount = count_value; if(tempCount != 0) { printf("WDT timeout in %d seconds.\n", tempCount); registerValue |= 0x40; //Enable WDT output through KBRST } else { printf("WDT is Disabled.
NuPRO-E42 Appendix C - System Resources C.
C.
NuPRO-E42 C.
IRQ Lines APIC Mode IRQ# Typical Interrupt Resource Connected to Pin Available 0 System Timer N/A No 1 Keyboard controller N/A No 2 PCI / ISA N/A No 3 Serial Port 2 (COM2) / PCI / ISA IRQ3 via SERIRQ, IRQ3 at ISA bus Note (1) 4 Serial Port 1 (COM1) / PCI / ISA IRQ4 via SERIRQ, IRQ4 at ISA bus Note (1) 5 Serial Port 3 (COM3) / PCI / ISA IRQ5 via SERIRQ, IRQ5 at ISA bus Note (1) 6 Serial Port 4 (COM4) / PCI / ISA IRQ6 via SERIRQ No 7 Parallel Port / Serial Port 5 (COM5) / PCI
NuPRO-E42 Typical Interrupt Resource Connected to Pin Available N/A PCIE Port 0/1/2/3/4/5/6/7, P.E.G. Root Port, SATA Host controller, SMBus Controller, Thermal Controller, SOL (COM7) Yes 19 N/A PCIE Port 0/1/2/3/4/5/6/7, P.E.G.
PCI Configuration Space Map Bus # Device # Function # Routing Description 00h 00h 00h N/A Intel Host Bridge 00 02H 00H Internal Intel IGD 02 00H 0FFH N/A P.E.G.
NuPRO-E42 Bus # Device # Function # Routing Description 14h 00h 0FFh Internal PCIE Port #3 15h 00h 0FFh Internal Intel 82574L LAN Controller 16h 00h 0FFh Internal PCIE Port #5 17h 00h 0FFh Internal USB 3.
PCI Interrupt Routing Map PIRQ A B C D INT Line INTA INTB INTC INTD P.E.G.
NuPRO-E42 Important Safety Instructions For user safety, please read and follow all instructions, WARNINGS, CAUTIONS, and NOTES marked in this manual and on the associated equipment before handling/operating the equipment. X Read these safety instructions carefully. X Keep this user’s manual for future reference. X Read the specifications section of this manual for detailed information on the operating environment of this equipment.
X Never attempt to fix the equipment. Equipment should only be serviced by qualified personnel. A Lithium-type battery may be provided for uninterrupted, backup or emergency power. WARNING: X 78 Risk of explosion if battery is replaced with one of an incorrect type. Dispose of used batteries appropriately.
NuPRO-E42 Getting Service Contact us should you require any service or assistance. ADLINK Technology, Inc. Address: 9F, No.166 Jian Yi Road, Zhonghe District New Taipei City 235, Taiwan ᄅؑקխࡉ৬ԫሁ 166 ᇆ 9 ᑔ Tel: +886-2-8226-5877 Fax: +886-2-8226-5717 Email: service@adlinktech.com Ampro ADLINK Technology, Inc. Address: 5215 Hellyer Avenue, #110 San Jose, CA 95138, USA Tel: +1-408-360-0200 Toll Free: +1-800-966-5200 (USA only) Fax: +1-408-360-0222 Email: info@adlinktech.com ADLINK Technology (China) Co.
ADLINK Technology, Inc. (French Liaison Office) Address: 6 allée de Londres, Immeuble Ceylan 91940 Les Ulis, France Tel: +33 (0) 1 60 12 35 66 Fax: +33 (0) 1 60 12 35 66 Email: france@adlinktech.com ADLINK Technology Japan Corporation Address: 〒101-0045 東京都千代田区神田鍛冶町 3-7-4 神田 374 ビル 4F KANDA374 Bldg. 4F, 3-7-4 Kanda Kajicho, Chiyoda-ku, Tokyo 101-0045, Japan Tel: +81-3-4455-3722 Fax: +81-3-5209-6013 Email: japan@adlinktech.com ADLINK Technology, Inc.
