ASD26-MLC/MA2 Series 2.5" SATA 6 Gb/s & SATA 3 Gb/s Solid State Drive Specification Revision: Date: Part Number: 1.03 December 6, 2012 50-1Z114-1030 Advance Technologies; Automate the World.
Document History 2 Revision Date 1.00 1.01 1.02 2012/02/02 2012/04/02 2012/07/02 1.
Copyright 2012 ADLINK Technology, Inc. Disclaimer The information in this document is subject to change without prior notice in order to improve reliability, design, and function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.
Table of Contents 4 1 Introduction .........................................................................5 1.1 1.2 1.3 1.4 1.5 1.6 1.7 Overview................................................................................................. 5 Product Specification................................................................................... 5 Functional Block Diagram ............................................................................12 Product Image ....................................
1 Introduction 1.1 Overview The ASD26-MLC (ASD26-MLC & ASD26-MA2) series 2.5" SATA Solid State Drive (SSD) delivers leading performance in an industry standard 2.5" form factor while simultaneously improving system responsiveness for mobile applications over standard rotating drive media or hard disk drives.
1.2.3. Flash: Multi-Level Cell (MLC) component with Toggle-Mode (24nm) 1.2.4.
1.2.5.
1.2.6. Power On to Ready: Type Average Latency Power on to Ready 1s Table 4: Latency Specifications Notes: 1. Write cache enabled 2. Device measured using Drive Master 3. Power on to ready time assumes proper shutdown (Power removal preceded by STANDBY command) 1.2.7. Compatibility -- SATA Revision 3.0 compliant Compatible with SATA 1.5 Gb/s, 3.0 Gb/s & 6.0 Gb/s interfaces -- SATA Revision 2.0 compliant for ASD26-MA2 series Compatible with SATA 1.5 Gb/s, 3.
1.2.10. Power Consumption Capacity 32 GB Description Operating voltage for 5V (+/- 5%) Min 4.75 Max 5.25 Unit V 64 GB Operating voltage for 5V (+/- 5%) 4.75 5.25 V 128 GB Operating voltage for 5V (+/- 5%) 4.75 5.25 V 256 GB Operating voltage for 5V (+/- 5%) 4.75 5.25 V 512 GB Operating voltage for 5V (+/- 5%) 4.75 5.25 V Table 7: Operating Voltage Capacity Mode Type Unit Active (average) 2.8 W Idle (average) 0.7 W Active (average) 0.95 W Idle (average) 0.
1.2.12. Reliability Parameter Mean Time between Failure (MTBF) Value > 1,500,000 hours Power on/off cycles 50,000 cycles Minimum useful life 3 years Table 10: Reliability specifications 1.2.13. Shock and Vibration: Item Mode Non-operating Timing/Frequency At 0.5 msec Max 1500G Shock1 Non-operating At 1 msec 1500G Non-operating At 2 msec 1000G Operating 7~800 Hz 2.17Grms Non-operating 7~800 Hz 3.08Grms Vibration2 Table11: Shock and Vibration Notes: 1.
1.2.14. Electromagnetic Immunity: Electromagnetic Immunity tests assume the SSD is properly installed in the representative host system. The drive operates properly without errors degradation in performance when subjected to radio frequency (RF) environments defined in the following table. Test Description Contact, HCP, VCP: ±8KV Air: ±15KV 80~1000MHz, 3V/m, 80% AM with 1 KHz sine Radiated RF immunity 900 MHz, 3 V/m, 50% pulse modulation at 200Hz ±1KV on AC mains Electrical fast transient ±0.
1.2.17. Part Numbers: Standard Operating Temperature Range: 0°C to 70°C Product Name Part No. 92-99059-5510 ASD26-MLC32G-CT 92-99059-6110 ASD26-MA2032-ET ASD26-MLC64G-CT 92-99059-5410 ASD26-MA2064-ET 92-99059-6010 ASD26-MLC128G-CT 92-99059-5110 ASD26-MLC256G-CT 92-99059-5210 ASD26-MLC512G-CT 92-99059-5310 1.
1.
1.5 Mechanical Drawing: Dimensions: 100.0 x 69.8mm x 9.
1.6 Architecture The ASD26-MLC series 2.5" SATA Solid State Drive (SSD) utilizes a cost effective system-on-chip (SoC) design to provide a full 6 Gb/s bandwidth with the host while managing multiple flash memory devices on multiple channels internally. 1.7 Hot Plug Support Hot Plug insertion and removal are supported when the correct connector and an appropriate operating system (OS) are used as described in the SATA 3.0 Specification.
2 Pin Locations and Signal Descriptions 2.1 Pin Locations The data and power connector pin locations of the ASD26-MLC series 2.5" SATA SSD are as shown below. 2.
Power Connector: Name P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 Type V33 V33 V33 GND GND GND V5 V5 V5 GND P11 DAS/DSS P12 P13 P14 P15 GND V12 V12 V12 Description 3.3V Power 3.3V Power 3.3V Power, Pre-change 5V Power, Pre-change 5V Power 5V Power Device Activity Signal / Disable Staggered Spin up 12V Power, Pre-change 12V Power 12V Power Table 14: Serial ATA Power Connector Pin Definitions Note: 1. All pins are in a single row, with a 1.27mm (0.05”) pitch 2.
3 ATA Command Sets 3.1 ATA Command The ASD26-MLC series 2.5" SATA SSD supports all the mandatory ATA commands defined in the ATA/ATAPI-8 specification. 3.1.1 ATA General Feature Command Set The ASD26-MLC series 2.
3.1.2 Identify Device Data The following table details the sector data returned after issuing an IDENTIFY DEVICE command.
Word F=Fixed V=Variable X=Both Default Value Description 64 F 0007h Multi-word DMA modes supported/selected 65 F 0003h PIO modes supported 66 F 0078h 67 F 0078h 68 F 0078h 69-70 F 0078h 71-74 F 0h 75 F 0h 76 F 001Eh Queue depth 77 F 0106h Serial ATA capabilities 78 F 0h Reserved for future Serial ATA definition 79 F 0048h Serial ATA features supported 80 V 0040h Serial ATA features enabled 81 F 00FCh Major Version Number 82 F 001Ah Minor Version N
Word F=Fixed V=Variable X=Both Default Value Description 95 V 0h Vendor’s recommended and actual acoustic management value 96 F 0h Stream Minimum Request Size 97 V 0h Streaming Transfer Time - DMA 98-99 V 0h Streaming Access Latency - DMA and PIO 100-103 F 0h Streaming Performance Granularity 125,045,424 (64GB) Maximum user LBA for 48-bit Address feature set 104 V 105 Specification 106 V 0h Streaming Transfer Time - PIO 107 F 0h Reserved 108-111 F 4000h Physical sector
Word F=Fixed V=Variable X=Both Default Value Description 235 F 0h Reserved 236-254 0001h Reserved 255 02A0h Reserved 236-254 F 0h Reserved 255 X varies Integrity word (checksum and signature) Table 15: Returned Sector Data Notes: 1. F=Fixed. The content of the word is fixed and does not change for removable media devices, these values may change when media is Removed or changed. 2. V=Variable.
3.3 Security Mode Feature Set The ASD26-MLC series 2.5" SATA SSD supports the Security Mode command set, which consist of ．SECURITY SET PASSWORD ．SECURITY UNLOCK ．SECURITY ERASE PREPARE ．SECURITY ERASE UNIT ．SECURITY FREEZE LOCK ．SECURITY DISABLE PASSWORD 3.4 SMART Command Set The ASD26-MLC series 2.5" SATA SSD supports the SMART command set, which consist of ．SMART ENABLE OPERATIONS ．SMART DISABLE OPERATIONS ．SMART ENABLE/DISABLE AUTOSAVE ．SMART RETURN STATUS The ASD26-MLC series 2.
Subcommand Code SMART ATTRIBUTE VALUES (READ DATA) D0h READ ATTRIBUTE THRESHOLDS D1h ENABLE/DISABLE ATTRIBUTE AUTOSAVE D2h SAVE ATTRIBUTE VALUES D3h EXECUTE OFF-LINE IMMEDIATE D4h LBA Low value EXECUTE SMART OFF-LINE ROUTINE 00h EXECUTE SMART SHORT SELF-TEST ROUTINE (OFFLINE) 01h EXECUTE SMART EXTENDED SELF-TEST ROUTINE (OFFLINE) 02h ABORT OFF-LINE ROUTINE 7Fh EXECUTE SMART SHORT SELF-TEST ROUTINE (CAPTIVE) 81h EXECUTE SMART EXTENDED SELF-TEST ROUTINE (CAPTIVE) 82h READ LOG SECTOR
．READ NATIVE MAX ADDRESS ．FLUSH CACHE EXT ．READ DMA EXT ．READ NATIVE MAX ADDRESS EXT ．READ SECTOR(S) EXT ．READ VERIFY SECTOR(S) EXT ．SET MAX ADDRESS EXT ．WRITE DMA EXT ．WRITE MULTIPLE EXT ．WRITE SECTOR(S) EXT 3.7 Device Configuration Overlay Command Set The ASD26-MLC series 2.5" SATA SSD supports the Device configuration Overlay command set, which consists of ．DEVICE CONFIGURATION FREEZE LOCK ．DEVICE CONFIGURATION IDENTITY ．DEVICE CONFIGURATION RESTORE ．DEVICE CONFIGURATION SET 3.
4 SATA Command Sets 4.1 SATA Command The SATA 3.0 Specification is a super set of the ATA/ATAPI-8 specification with regard to supported commands. The ASD26-MLC series 2.5" SATA 6.0 Gb/s SSD supports the following features which are unique to the SATA 3.0 Specification. 4.1.1. Software Settings Preservation The ASD26-MLC series 2.5" SATA SSD supports the SET FEATURES parameter to enable/disable the preservation of software settings. 4.1.2. Native Command Queuing The ASD26-MLC series 2.
5 References This document references standards defined by a variety of organizations as listed below. Date Title Location Dec 2008 VCCI http://www.vcci.or.jp/vcci_e/general/jo in/index.html July 2007 ROHS Search for material description datasheet at http://intel.pcnalert.com July 2007 SFF-8144, 1.8” drive form factor http://www.sffcommittee.org February 2007 Serial ATA Revision 2.6 http://www.sata-io.org May 2006 SFF-8223, 2.5” Drive w/Serial Attachment Connector http://www.sffcommittee.
6 Getting Service Contact us should you require any service or assistance. ADLINK Technology, Inc. Address: 9F, No.166 Jian Yi Road, Zhonghe District New Taipei City 235, Taiwan 新北市中和區建一路 166 號 9 樓 Tel: +886-2-8226-5877 Fax: +886-2-8226-5717 Email: service@adlinktech.com Ampro ADLINK Technology, Inc. Address: 5215 Hellyer Avenue, #110, San Jose, CA 95138, USA Tel: +1-408-360-0200 Toll Free: +1-800-966-5200 (USA only) Fax: +1-408-360-0222 Email: info@adlinktech.com ADLINK Technology (China) Co., Ltd.
LiPPERT ADLINK Technology GmbH Address: Hans-Thoma-Strasse 11, D-68163, Mannheim, Germany Tel: +49-621-43214-0 Fax: +49-621 43214-30 Email: emea@adlinktech.com ADLINK Technology, Inc. (French Liaison Office) Address: 15 rue Emile Baudot, 91300 Massy CEDEX, France Tel: +33 (0) 1 60 12 35 66 Fax: +33 (0) 1 60 12 35 66 Email: france@adlinktech.com ADLINK Technology Japan Corporation Address: 〒101-0045 東京都千代田区神田鍛冶町 3-7-4 神田 374 ビル 4F KANDA374 Bldg.
