SABER SPOT GO User Instructions
©2019 ADJ Products, LLC all rights reserved. Information, specifications, diagrams, images, and instructions herein are subject to change without notice. ADJ Products, LLC logo and identifying product names and numbers herein are trademarks of ADJ Products, LLC. Copyright protection claimed includes all forms and matters of copyrightable materials and information now allowed by statutory or judicial law or hereinafter granted.
Saber Spot GO Table of Contents Introduction 3 Safety Guidelines 5 Features I Warranty Registration Battery Precautions Installation I Safety Strap Overview 4 6 8 9 DMX Addressing 10 Color Macro Chart 13 DMX Modes System Menu Operating Instructions WiFly Set Up I WiFly Master-Slave I Runtime Mode ADJ UC IR/Airstream IR Control Dimmer Curve Chart Dimensional Drawings Frost Filter Installation I Trouble Shooting I Cleaning Limited Warranty (USA Only) Specifications 11 15 16 19 20 21 22 23
Saber Spot GO Introduction Unpacking: Thank you for purchasing the Saber Spot GO by ADJ Products, LLC. Every Saber Spot GO has been thoroughly tested and has been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have occurred during shipping. If the carton appears to be damaged, carefully inspect your fixture for any damage and be sure all accessories necessary to operate the unit has arrived intact.
Saber Spot GO Features / Included • Three Operating Modes • Electronic Dimming 0-100% • 5 Selectable Dimming Curves • Wireless DMX-512 Protocol • 64 Color Macros • • • • 12 DMX Channel Modes: 3/4/4/5/6/6/7/8/8/9/11/12 Rechargeable Lithium Battery Built-In ADJ’s WiFly TransCeiver Wireless DMX ADJ UC IR compatible (Not Included) and Airstream IR compatible (Transmitter Not Included) Included: • Charging Power Supply • 10 Degree & 45 Degree Frost Filters • Lens Retainer Ring • 2 x Velcro Safety Strap Sa
Saber Spot GO Safety Guidelines For Your Own Personal Safety, Please Read and Understand This Manual Completely Before You Attempt To Install Or Operate This Unit! • To reduce the risk of electrical shock or fire, do not expose this unit rain or moisture • Do not spill water or other liquids into or on to your unit. • Be sure that the local power outlet match that of the required voltage for your unit. • Do not attempt to operate this unit if the power cord has been frayed or broken.
Saber Spot GO Battery Precautions HANDLING OF BATTERIES DO NOT SHORT CIRCUIT THE BATTERY Try to never short circuit the battery. It generates a very high current which could cause the battery to overheat which may result in electrolyte gel leakage, harmful fumes, or explosion. The LIR tabs may easily short-circuit by placing them on conductive surface. A short circuit may lead to heat build up and damage of the battery.
Saber Spot GO Battery Precautions BATTERY STORAGE When storing the battery, it should be stored at room temperature, with a charge of at least 50%. We recommend that during long periods of storage that the battery be charged every 6 months. Doing this will prolong the life of the battery and will also make sure that the battery charge does not fall below the 30% mark.
Saber Spot GO Installation Fixtures should be mounted using a mounting clamp (not included), affixing it to the mounting bracket that is provided with the unit. Always ensure that the fixture is firmly fixed to avoid vibration and slipping while operating. Always ensure that the structure to which you are attaching the unit is secure and is able to support a weight of 10 times the unit’s weight.
Saber Spot GO Overview SAFETY CABLE RIGGING POINT POWER SWITCH POWER IN CHARGING INDICATOR LCD DISPLAY CONTROL PANEL (MODE/UP/DOWN/ENTER) MAGNETS ADJ Products, LLC - www.adj.
Saber Spot GO DMX Addressing All fixtures should be given a DMX starting address when using a DMX controller, so the correct fixture responds to the correct control signal. This digital starting address is the channel number from which the fixture starts to “listen” to the digital control signal sent out from the DMX controller. The assignment of this starting DMX address is achieved by setting the correct DMX address on the digital control display on the fixture.
Saber Spot GO 3 CH 4 CH 4 CH 5 CH DMX Modes 6 CH 6 CH 7 CH 8 CH 8 CH 9 CH HSI RGBW HSI+ RGBW sRGBWI RGBW RGBW RGBW 16Bit HSI 1 1 2 1 1 1 1 11 CH 12 CH sRGBWI RGBW 2 1 2 2 2 3 2 2 2 3 3 2 4 3 3 4 3 3 3 5 4 3 6 4 4 5 4 4 4 7 5 4 8 VALUES FUNCTIONS 000-255 RED 0-100% 000-255 RED FINE 0-100% 000-255 GREEN 0-100% 000-255 GREEN FINE 0-100% 000-255 BLUE 0-100% 000-255 BLUE FINE 0-100% 000-255 WHITE 0-100% 000-255 WHITE FINE 0-100% SHUTTER & STROBING 5
Saber Spot GO 3 CH 4 CH 4 CH 5 CH DMX Modes 6 CH 6 CH 7 CH 8 CH 8 CH 9 CH HSI RGBW HSI+ RGBW sRGBWI RGBW RGBW RGBW 16Bit HSI 11 CH 12 CH sRGBWI RGBW VALUES FUNCTIONS AUTO PROGRAMS 000 001-020 021-040 041-060 061-080 081-100 101-120 121-140 141-160 161-180 181-200 201-220 221-240 241-250 251-255 OFF AUTO PROGRAM 1 AUTO PROGRAM 2 AUTO PROGRAM 3 AUTO PROGRAM 4 AUTO PROGRAM 5 AUTO PROGRAM 6 AUTO PROGRAM 7 AUTO PROGRAM 8 AUTO PROGRAM 9 AUTO PROGRAM 10 AUTO PROGRAM 11 AUTO PROGRAM 12 AUTO PROGRAM 13
Saber Spot GO Color No. Color Macro Chart DMX RGBW COLOR INTENSITY VAULE RED GREEN BLUE Color No.
Saber Spot GO Y Color No.
Saber Spot GO System Menu Software Update Please Wait.... ADJ SOFTWARE V1.01 MENU FUNCTION DMX MODE ADDR: 001 001-510 CHANNEL 3/4/4/5/6/6/7/8/8/9/11/12CH Slave Slave Setting LOOK Store: 01-13 Reset ? Restore Factory Defaults Manual Manual Dimmer R000-255 / G000-255 / B000-255 / W000-255 / Strobe: S000-255 DimCurve 5 Dimmer Curves Standard/Stage/TV/Architec/Theatre NO DMX Blackout/Hold/LOOK White BL TempUnit White Balance R255 / G255 / B255 / W255 Temp.
Saber Spot GO Operating Instructions When making adjustments press ENTER to confirm your setup. To exit without making any adjustments press the MODE button. The display will lock after 1 minute. Press the MODE button for 7 seconds to unlock. DMX MODE - DMX Address Setting. 1. Press either the MODE, UP, or DOWN buttons until “DMX MODE” is displayed, press ENTER. 2. The current address will now be displayed and flashing. Press the UP or DOWN buttons to find your desired address.
Saber Spot GO DimCurve - This will let select your desired dimmer curve. Operating Instructions 1. Press either the MODE, UP, or DOWN buttons until “DimCurve” is displayed, and press ENTER. 1 of 5 dimmer curves will be displayed. “Standard”, “Stage”, “TV”, “Architec” (Architectural), or “Theatre”. See the dimmer curve chart on page 21 for more info. 2. Press the UP or DOWN buttons to find your desired dimmer curve and press the ENTER button to confim your selection.
Saber Spot GO Operating Instructions Autolock - This function will lock the control panel after a minute of no use. Press the MODE button for at least 7 seconds to unlock. 1. Press either the MODE, UP, or DOWN buttons until “AUTOLOCK” is displayed, press ENTER. 2. The display will show either “ON” or “OFF”. Press the UP or DOWN buttons to select “ON” to have the keys lock after 10 seconds, or “OFF” so that the keys will remain unlocked. 3. Press the ENTER button to confirm.
Saber Spot GO WiFly Set Up This unit can only be controlled using WiFly. Your DMX controller must be connected to a ADJ WiFly Transceiver to use this function. You are able to communicate up to 2500 feet/760 meters (open line of sight). 1. Follow the instructions on page 18 to set the WiFly channel. The channel must match the channel setting on the WiFly WiFly Transceiver. 2.
Saber Spot GO ADJ UC IR/ Airstream IR Control The ADJ UC IR (not included) infrared remote gives you control of various functions (See below). To control the Saber Spot GO you must aim the remote at the front of the fixture and be no more than 30 feet away. To use the ADJ UC IR you must first activate the fixtures infrared sensor, to activate the sensor please see the instructions on page 18. The ADJ Airstream IR remote transmitter (not included) plugs into the headphone jack of your iOS phone or tablet.
Saber Spot GO Dimmer Curve Chart DIMMER 100% 50% 10% 0% Time (ms) Rise Time 0 Sec Down Time 0 sec Fade Time 1 sec Fade Time 255 Dimming Curve Ramp Effect 0 Standard (default) Stage TV Architectural Theatre 255 0 Rise Time (ms) Down Time (ms) Rise Time (ms) Down Time (ms) 0 780 1180 1380 1580 0 1100 1520 1730 1940 0 1540 1860 2040 2230 0 1660 1940 2120 2280 ADJ Products, LLC - www.adj.
Saber Spot GO Dimensional Drawing 6.8” / 172mm 5” / 127mm 3.5” / 90mm 6.3” / 158.97mm 6.3” / 160mm 3.9” / 100mm ADJ Products, LLC - www.adj.
Saber Spot GO Frost Filter Installation 2. 1. 3. The Saber Spot GO comes with 2 frost filters. Before installation, peel off the adhesive backing on both sides of the lens. Install the frost filter in front of the main lens (1 & 2). Insert the inlcuded retainer ring by “squeezing” the ring and gently sliding it in place in front of the newly installed lens (3). Saber Spot GO Trouble Shooting Listed below are a few common problems the user may encounter, with solutions. Unit not responding to DMX: 1.
Saber Spot GO Limited arranty MANUFACTURER’S LIMITED WARRANTY A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products to be free of manufacturing defects in material and workmanship for a prescribed period from the date of purchase (see specific warranty period on reverse). This warranty shall be valid only if the product is purchased within the United States of America, including possessions and territories.
Saber Spot GO Power Supply: LEDs: Working Position: Power Draw: Weight: Dimensions: Colors: DMX Modes: Battery Charge Time: Battery Lifetime*: Battery Type: Battery Energy: Battery Weight: Battery Voltage: Battery Capacity: Total Lithium Ion Cells: Battery Wrap Material: Warranty**: * This depends on charging frequency **See Warranty page for more details Specifications DC 13-16V 1 x 15W RGBW 4-in-1 LED Any safe working position 27W 2.5 lbs./ 1.1 Kgs. 6.
