User manual
©American DJ® - www.Americandj.com - Flat Par CWWW9 User Manual Page 10©American DJ® - www.Americandj.com - Flat Par CWWW9 User Manual Page 9
Flat Par CWWW9 Operating Instructions
played. “XX” represents the displayed fade speed number.
2. Use the UP and DOWN buttons to adjust the fade speed. “8-01” is
the slowest speed, and “8-16” is the fastest. After you have selected
your desired color you can activate strobing by pressing the SET UP
button to enter the Flash (strobe) mode.
3. “7-XX” will be displayed, this is Flash mode. The Flash can be
adjusted between “7-00” (flash off) to “7-20” (fastest flash).
Sound Active Mode:
In this mode the Flat Par CWWW9 will react to sound, and chase through
the different colors.
1. Plug the fixture in and press the MODE button until “9-SO” is dis-
played.
2. The fixture will now change via sound.
Auto Mode:
1. Plug the fixture in and press the MODE button until “AUTO” is dis-
played. Auto mode is now active.
Infrared Receiver:
This function is used to activate and deactivate the infrared receiver.
When this function is activated you can control the fixture using the
ADJ LED RC (Remote Control). Please see page 11 for ADJ LED RC
controls and functions.
1. Plug the fixture in and press the MODE button until “Ir-X” is dis-
played. “X” represents either “1” (On) or “2” (Off).
2. Press the UP or DOWN buttons to either activate the remote func-
tion (1) or deactivate it (2).
Master-Slave Configuration:
This function will allows you to link units together to run in a Master-Slave
mode. In Master-Slave operation one unit will act as the controlling unit
and the others will react to the controlling units built-in programs. Any
unit can act as a Master or as a Slave however, only one unit can be pro-
grammed to act as the “Master.”
Master-Slave Connections and Settings:
1. Daisy chain your units via the XLR connector on the rear of the unit.
Use standard XLR data cables to link your units together. Remember
that the Male XLR connector is the input and the Female XLR con-
nector is the ouput. The first unit in the chain (master) will use the
female XLR connector only. The last unit in the chain will use the
male XLR connector only.
2. On the “Master” unit, set your desired operating mode. For the
“Slave” unit, press the MODE button until “SLAV” is displayed
3. Now connect the “Slave” unit to the “Master” unit using the XLR con-
nections.
Flat Par CWWW9 Master-Slave Configuration
MODE Color Temperature DMX Values
etihW mraW etihWlooC
19 7400K 255 2
18 7200K 255 11
17 7000K 255 20
16 6800K 255 30
15 6600K 255 42
14 6400K 255 56
13 6200K 255 72
12 6000K 255 91
11 5800K 255 113
10 5600K 255 138
9 5400K 255 170
8 5100K 255 231
7 5000K 255 255
6 4800K 204 255
5 4600K 161 255
4 4300K 106 255
3 4000K 61 255
2 3800K 35 255
1 3400K 0 255
Flat Par CWWW9 Color Preset Chart
Flat Par CWWW9 Power Cord Daisy Chain
With this feature you can connect the xtures to one another
using the IEC input and output sockets. The quantity that can be
connected is 20 xtures maximum. After 20 xtures you will need
to use a new power outlet. They must be the same xtures. DO
NOT mix xtures.