ULTRA HEX BAR 12 ADJ Products, LLC 6122 S. Eastern Ave. Los Angeles, CA 90040 USA Tel: 323-582-2650 / Fax: 323-725-6100 Web: www.adj.com / E-mail: info@americandj.com A.D.J. Supply Europe B.V. Junostraat 2 6468 EW Kerkrade Netherlands service@adjgroup.eu / www.adj.
©2015 ADJ Products, LLC all rights reserved. Information, specifications, diagrams, images, and instructions herein are subject to change without notice. ADJ Products, LLC logo and identifying product names and numbers herein are trademarks of ADJ Products, LLC. Copyright protection claimed includes all forms and matters of copyrightable materials and information now allowed by statutory or judicial law or hereinafter granted.
Ultra Hex Bar 12 Notes Ultra Hex Bar 12 Introduction Unpacking: Thank you for purchasing the Ultra Hex Bar 12 by ADJ Products, LLC. Every Ultra Hex Bar 12 has been thoroughly tested and has been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have occurred during shipping. If the carton appears to be damaged, carefully inspect your fixture for any damage and be sure all accessories necessary to operate the unit has arrived intact.
Ultra Hex Bar 12 Features Ultra Hex Bar 12 Notes • • • • • • • Multi-Colors Six Operating Modes Electronic Dimming 0-100% Built in Microphone DMX-512 protocol 3-Pin DMX Connection 5 DMX Modes: 6 Channel Mode, 7 Channel Mode, 8 Channel Mode, 12 Channel Mode, & 36 Channel Mode. • ADJ RFC compatiable (Sold Separately) • Power Cord Daisy Chain (See page 22) Ultra Hex Bar 12 Warranty Registration The Ultra Hex Bar 12 carries a 2 year limited warranty.
Ultra Hex Bar 12 Warranty MANUFACTURER’S LIMITED WARRANTY A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products to be free of manufacturing defects in material and workmanship for a prescribed period from the date of purchase (see specific warranty period on reverse). This warranty shall be valid only if the product is purchased within the United States of America, including possessions and territories.
Ultra Hex Bar 12 Set Up Power Supply: The ADJ Ultra Hex Bar 12 contains a automatic voltage switch, which will auto sense the voltage when it is plugged into the power source. With this switch there is no need to worry about the correct power voltage, this unit can be plugged in anywhere. DMX-512: DMX is short for Digital Multiplex. This is a universal pro- tocol used as a form of communication between intelligent fixtures and controllers.
POWER Ultra Hex Bar 12 POWER DMX512 Photometric Chart DMX+,DMX-,COMMON Ultra Hex Bar 12 Set Up nect the cable’s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR’s outer casing. Grounding the shield could cause a short circuit and erratic behavior.
Ultra Hex Bar 12 Operating Instructions Menu Lock: You can set the menu to lock after 30 seconds. When the menu is set to lock, press and hold the MODE button for at least 5 seconds to unlock and access the menu. To set the menu to lock after 30 seconds, press the MODE button until “OTHER” is displayed. Press the SET UP button so that LOCK:XXX” is displayed. “XXX” represents either ON or OFF. Press the UP or DOWN buttons so that ON is displayed. Now the menu will lock after 30s.
Ultra Hex Bar 12 Channel 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 Value 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 36 Channel - DMX Values & Functions Function RED 0% - 100% PIXEL 1 & 2 GREEN 0% - 100% PIXEL 1 & 2 BLUE 0% - 100% PIXEL
Ultra Hex Bar 12 Operating Instructions the UP and DOWN buttons to adjust intensity. 8. After you have adjusted the colors to make your desired color you can then activate strobing by pressing the SET UP button to enter the strobe mode. 9. “STRO: XX” will be displayed, this is strobe mode. The strobe can be adjusted between “00” (flash off) to “15” (fastest flash). Ultra Hex Bar 12 Channel 10 Static Color Mode: 1. Plug the fixture in and press the MODE button until “CLR MACS” is displayed.
Ultra Hex Bar 12 Channel 1 Value 12 Channel - DMX Values & Functions 0 - 255 2 0 - 255 3 0 - 255 4 0 - 255 5 0 - 255 6 0 - 255 7 0 - 255 8 0 - 31 32 - 63 64 - 95 96 - 127 128 - 159 160 - 191 192 - 223 224 - 255 9 10 0 - 255 0 1 - 24 25 - 35 36 - 46 47 - 57 58 - 68 69 - 79 80 - 90 Function RED 0% - 100% GREEN 0% - 100% BLUE 0% - 100% WHITE 0% - 100% AMBER 0% - 100% UV 0% - 100% COLOR MACROS (See Color Macro Chart on page 20) STROBING OFF LED ON STROBING SLOW - FAST LED ON STROBE PULSE
Ultra Hex Bar 12 Operating Instructions 3. Use the UP or DOWN buttons to either activate the remote function (On) or deactivate it (Off). DMX State: Ultra Hex Bar 12 Channel 1 This mode can be used as a precaution mode, that in case the DMX signal is lost, the operating mode chosen in the setup is the running mode the fixture will go into when the DMX signal is lost. You can also set this as the operating mode you would like the unit to return to when power is applied. 1.
Ultra Hex Bar 12 Channel 1 Value 0 - 255 2 0 - 255 3 0 - 255 4 0 - 255 5 0 - 255 6 0 - 255 Ultra Hex Bar 12 Channel 1 2 3 4 5 6 7 Value 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 6 Channel - DMX Values & Functions Function RED 0% - 100% GREEN 0% - 100% BLUE 0% - 100% WHITE 0% - 100% AMBER 0% - 100% UV 0% - 100% 7 Channel - DMX Values & Functions Function RED 0% - 100% GREEN 0% - 100% BLUE 0% - 100% WHITE 0% - 100% AMBER 0% - 100% UV 0% - 100% MASTER DIMMER 0% - 100% ADJ
Ultra Hex Bar 12 ADJ RFC Operation The ADJ RFC remote (sold seperately) has many different functions and allows you to control your Ultra Hex Bar 12 from long distance. The ADJ RFC remote can control your system up to 150 ft. To use the RFC you must first activate the fixtures receiver, to activate the receiver please see the instructions on pages 10-11. BLACKOUT - Pressing this button will blackout the fixture. Press this button for more then 3 seconds to activate default mode.
