User manual
ADJ Products, LLC - www.adj.com - WiFly EXR QA5 IP User Manual Page 16
tion (On) or deactivate it (Off).
WiFLY Address Setting/WiFly On/Off:
This function is used to set the WiFly address and activate/deactivate
the WiFly function. The address must match the address that is set to
your WiFly TransCeiver or WiFly controller.
1. Plug the fixture in and press the MODE button until “WIFI SET
ADDR: XX” is displayed. “XX” represents a number between
00-15.
2. Use the UP or DOWN buttons to find and set your desired WiFly
address. The address must match the address that is set to your
WiFly TransCeiver or WiFly controller.
3. After you have found and set your WiFly address, press the SET
UP button to activate WiFly. “WIFI SET STAT: XXX” will now be
displayed. Use the UP or DOWN button to set the display to “On”
to activate WiFly. To deactivate WiFly set the display to “Off”.
DMX State:
This mode can be used as a precaution mode, that in case the DMX
signal is lost, the operating mode chosen in the setup is the running
mode the xture will go into when the DMX signal is lost. You can also
set this as the operating mode you would like the unit to return to when
power is applied.
1. Plug the fixture in and press the MODE button until “DMX MODE
ADDR:XXX” is displayed.
2. Press the SET UP button until “DMX MODE NO: XXXX” is dis-
played. “XXXX” represents the current DMX state that is displayed.
3. Use the UP or DOWN buttons to select the operating mode you
would like the unit to start up in when power is applied or the
DMX signal is lost.
• AUTO - If the DMX signal is lost or power is applied, the unit will auto-
matically into Auto Run.
• BLACK - If the DMX signal is lost or power is applied, the unit will
automatically go into stand by mode.
• HOLD - If the DMX signal is lost the xture will stay in the last DMX
set up. If power is applied and this mode is set, the unit will automati-
WiFly EXR QA5 IP Operating Instructions
ADJ Products, LLC - www.adj.com - WiFly EXR QA5 IP User Manual Page 19
WiFly EXR QA5 IP WiFly Set Up
WiFly EXR QA5 IP WiFly Master-Slave Set Up
With this feature you are able to control the unit with DMX without the
need of XLR cables. Your DMX controller must be connected to a ADJ
WiFly Transceiver to use this function. You are able to communicate
up to 2500 feet/760 meters (open line of sight).
1. Follow the instructions on pages 15-16 to set the WiFly address
and to activate WiFly. The address must match the address set
on the WiFly WiFly Transceiver. Note: WiFly address 15 operates
in a receive only state.
2. After you have set the WiFly address, follow the DMX instructions
on page 14 to select your desired DMX Channel mode and set
your DMX address.
3. Apply power to the ADJ WiFly Transceiver. The fixture must be set
up first before you apply power to WiFly Transceiver.
4. If everything is set up properly and the fixture is receiving a
Wireless signal, you should now be able to control it with a DMX
controller.
This feature will let you link units to run in a master-slave mode with-
out the use of XLR cables.
1. Follow the instructions on pages 15-16 to set the WiFly address
and to activate WiFly. The addresses on each fixture must be the
same. Note: WiFly address 15 acts in a operates in a received
only state.
2. After you have set the WiFly address, select your “Master” unit
and set your desired operating mode.
3. For the “Slave” unit(s), put the unit in Slave mode. See page 12
Master-Slave configuration when setting the unit as a Slave.
4. If everything is set up correctly, the “Slave” units will start follow-
ing the “Master” unit.