User manual

ADJ Products, LLC - www.adj.com - PinPoint Gobo User Manual Page 5
1. Handling of Batteries
1.1 Do Not Short Circuit the Battery
Try to never short circuit the battery. It generates a very high current
which could cause the battery to overheat which may result in elec-
trolyte gel leakage, harmful fumes, or explosion. The LIR tabs may
easily short-circuit by placing them on conductive surface. A short cir-
cuit may lead to heat build up and damage of the battery. An appro-
priate circuitry with PCM is employed to protect accidental short
circuit of the battery pack.
1.2 Mechanical shock
Droping the unit, impact hit, bending, etc. may cause failure or short-
end life of the LIR battery.
2. Other
2.1 Battery connection
1). Direct soldering of wire leads or devices to the battery is strictly
prohibited.
2). Lead tabs with pre-soldered wiring shall be spot welded to the
batteries. Direct soldering may cause damage of components, such
as separator and insulator, by heat build up.
2.2 Prevention of short circuit within a battery pack
There is enough insulation layers between wiring and the batteries to
provide extra safety protection. The battery pack is constructed in a
way that no short circuit will occur which may cause smoke or re.
2.3 Do No Disassemble the Batteries
1). Never disassemble the batteries.
Doing this may cause a internal short circuit in the battery, which may
lead to harmful fumes, re, explosion, or other problems.
2). Electrolyte Gel is harmful
Electrolyte Gel should not leak from the LIR battery. Should the
electrolyte gel come into contact with the skin or eyes, ush the area
of contact immediately with fresh water and seek medical attention
immediately.
2.4 Do Not Expose the Battery to Heat or Fire
Never incinerate or dispose of the batteries in re. This may cause an
explosion, which would be very dangerous.
PinPoint Gobo Battery Precautions
ADJ Products, LLC - www.adj.com - PinPoint Gobo User Manual Page 10
The UC IR (sold separately) infrared remote gives you control of
various functions (See below). To control the fixture you must aim the
remote at the front of the fixture and be no more than 30 feet away.
The PinPoint Gobo comes with the Airstream IR remote transmit-
ter. The transmitter plugs into the headphone jack of your iOS phone
or tablet. To control your IR fixture you must raise the volume to the
maximum on your iOS phone or table and aim the transmitter at the
front of the fixture and be no more than 15 feet away. After you have
purchased the Airstream IR transmitters, the app is a free download
from the app store for your iOS phone or tablet. The app comes with
3 pages of control depending on the IR fixture you are using. Please
see below for IR functions including the corresponding app page.
Works with App page 1.
STAND BY - Pressing this button will blackout the fixture. Press the
button again to return to the initial state. This button is also used to
switch between full on mode, 3.3W mode, and energy saving mode.
To switch between the modes see page 7.
FULL ON - Hold this button down to fully light up the unit. When you
let the button go, the unit will return to its previous state.
FADE/GOBO - Press this button to activate fade mode.
“DIMMER +” and “DIMMER -” - Use these buttons to output inten-
sity.
STROBE - Press and hold this button for strobing.
COLOR - Press this button to activate white color mode. Use the
“DIMMER +” and “DIMMER -” to adjust output intensity. Press and
hold the strobe button to activate strobing.
1-9 - When SHOW 0 is active button’s 1 & 2 will switch between fast
fade and slow fade. Button’s 3-9 are not valid for this fixture.
SHOW 0 - Press this button to activate show mode. Use button’s 1 &
2 to switch between fast fade and slow fade.
PinPoint Gobo UC IR Remote & Airstream IR