Install Instructions

Exceptional protection for 1½” hydronic heating systems.
MagnaClean
®
DualXP has been developed by the industry leading and multi-award
winning company that pioneered magnetic filtration within this sector. ADEY’s filters
are already protecting over three million heating systems throughout Europe.
MagnaClean DualXP can be installed anywhere on the main circuit. However, to
achieve the best level of protection for the boiler or baseboard, it is recommended
to install the filter after the last radiator on the system and before the boiler.
It is important to install valves either side of the MagnaClean DualXP.
Isolation valves, fittings for copper pipework and reducing bushes are not included.
Installation
The following instructions are designed to
support engineers in the safe and effective
installation and servicing of MagnaClean
DualXP and should be followed at all times.
Any queries should be directed to ADEY on
844 378 0442
MagnaClean DualXP is suitable for both
residential hydronic heating systems shown
here as well as larger light commercial systems.
Open vented system Tankless / Sealed system
Your system is protected by
Annual service required
adeyusa.com
Servicing
D
DETAIL D
SCALE 1 : 2
Dual
Note: We firmly recommend
MagnaClean DualXP is installed
and serviced by a qualified
heating engineer.
Knurled nuts should be
hand-tightened only.
In both diagrams, position A is best
practice, while B is suitable.
D
DETAIL D
SCALE 1 : 2
1 2 3
4 5
6 7
D
DETAIL D
SCALE 1 : 2
1
2
3
Open
1
Close
1
2
Open
3
Close
Remove
cover
1
2
3
Clean
Clean
4
Clean
1
2
1
1
D
DETAIL D
SCALE 1 : 2
D
DETAIL D
SCALE 1 : 2
D
DETAIL D
SCALE 1 : 2
2
3
Open
Close
5
û
û
C
15 ⁄”
1½“ iron
1
1”
1”
1½’’
NPT
1½’’
NPT
1
2
2
2
1
1
A
A
375
PIPE CUT LENGTH
118
FIXED PORT CENTRES
SECTION A-A
SCALE 1 : 2
1. AFTER CUTTING PIPE AND CUTTING
THREAD. FIT BOTTOM ELBOW ASSEMBLY.
2. BOTTOM ELBOW TO BE IN FULLY RETRACTED
POSITION, AFTER LOCKING BLACK NUT AGAINST RED
BUSH. TURN RED BUSH CLOCKWISE UNTIL COMPLETE
ASSEMBLY HAS BECOME RIGID (CONNECTION TO FILTER,
CANNOT BE TURNED).
3. FIT TOP ELBOW, DO NOT LOCK - MOVE
CONNECTION AND PUSH FILTER ON TO SPIGOTS -
DO NOT LOCK FILTER TO CONNECTORS.
4. LOCK CONNECTOR - BLACK NUT AGAINST RED
NUT ONLY.
5. LOCK CONNECTORS TO FILTER.
FITTING DUAL XP TO 1-1/2" PIPEWORK
3
Hold
1
1
û
ü
A
A
375
PIPE CUT LENGTH
118
FIXED PORT CENTRES
SECTION A-A
SCALE 1 : 2
1. AFTER CUTTING PIPE AND CUTTING
THREAD. FIT BOTTOM ELBOW ASSEMBLY.
2. BOTTOM ELBOW TO BE IN FULLY RETRACTED
POSITION, AFTER LOCKING BLACK NUT AGAINST RED
BUSH. TURN RED BUSH CLOCKWISE UNTIL COMPLETE
ASSEMBLY HAS BECOME RIGID (CONNECTION TO FILTER,
CANNOT BE TURNED).
3. FIT TOP ELBOW, DO NOT LOCK - MOVE
CONNECTION AND PUSH FILTER ON TO SPIGOTS -
DO NOT LOCK FILTER TO CONNECTORS.
4. LOCK CONNECTOR - BLACK NUT AGAINST RED
NUT ONLY.
5. LOCK CONNECTORS TO FILTER.
FITTING DUAL XP TO 1-1/2" PIPEWORK
2
ü
4¼”
A
A
375
PIPE CUT LENGTH
118
FIXED PORT CENTRES
SECTION A-A
SCALE 1 : 2
1. AFTER CUTTING PIPE AND CUTTING
THREAD. FIT BOTTOM ELBOW ASSEMBLY.
2. BOTTOM ELBOW TO BE IN FULLY RETRACTED
POSITION, AFTER LOCKING BLACK NUT AGAINST RED
BUSH. TURN RED BUSH CLOCKWISE UNTIL COMPLETE
ASSEMBLY HAS BECOME RIGID (CONNECTION TO FILTER,
CANNOT BE TURNED).
3. FIT TOP ELBOW, DO NOT LOCK - MOVE
CONNECTION AND PUSH FILTER ON TO SPIGOTS -
DO NOT LOCK FILTER TO CONNECTORS.
4. LOCK CONNECTOR - BLACK NUT AGAINST RED
NUT ONLY.
5. LOCK CONNECTORS TO FILTER.
FITTING DUAL XP TO 1-1/2" PIPEWORK
4
2
1
6
Hold
1
ü
1
7
1
1
2
2
ü
ü
Add
MC1+
Protector