ADEMCO LYNXR-EN Security System User Guide ARMED 1 2 RECORD VOLUME OFF ESCAPE 4 AWAY ADD STAY DELETE LIGHTS ON 7 SELECT K5964V3bx 5/04 Rev.
Your Honeywell security system is designed for use with devices manufactured or approved by Honeywell for use with your security system. Your Honeywell security system is not designed for use with any device that may be attached to your security system's keypad or other communicating bus if Honeywell has not approved such device for use with your security system.
TABLE OF CONTENTS SYSTEM OVERVIEW ................................................................................................................................5 Features .................................................................................................................................................5 General Operation .................................................................................................................................7 Quick View of System Functions ............
–4–
SYSTEM OVE OVERVIEW RVIEW Features General Information This system offers you three forms of protection: burglary, fire, and emergency, depending on the configuration of your system. The system consists of a master keypad for controlling system operation, various wireless sensors that provide perimeter and interior burglary protection, and optional smoke or combustion detectors to provide early fire warning.
SYSTEM OVERVIEW Features • AUX key function: Designated key lets you activate a predefined series of keystrokes with a single press of the AUX key plus user code, or manually send a pager message. It will also allow you to manually send a voice message to phone number that has been programmed by your installer. Ask your installer which of these features has been assigned to the AUX key in your LYNXR-EN. Refer to the AUX FUNCTION section for detailed information.
SYSTEM OVERVIEW General Operation Zones Your system's sensing devices have been assigned to various "zones." For example, the sensing device on your entry/exit door may have been assigned to zone 01, sensing devices on windows in the master bedroom to zone 02, and so on. These numbers appear on the display when an alarm or trouble condition occurs. UL LYNXR-EN is not intended for UL985 Household Fire applications unless a 24-hour backup battery (P/N LYNXRCHKIT-HC) is installed.
SYSTEM OVERVIEW General Operation until alarm bell timeout occurs. If your system is connected to a central monitoring station, an alarm message will be sent. To stop the alarm sounding, simply disarm the system. The zone(s) causing the alarm remain displayed indicating memory of alarm.
QUICK VIEW OF SYSTEM FUNCTIONS FUNCTIONS NOTE: = Boxes represent the entering of your 4-digit user code.
QUICK VIEW OF SYSTEM FUNCTIONS REMOTE PHONE CONTROL OPERATION To remotely disarm: --------------------- + [1] To remotely arm in AWAY mode: - + [2] To remotely arm in STAY mode: -- + [3] + [2] or [3] + [0] To remotely arm in AWAY or STAY mode with NO DELAY: To remotely activate X-10 devices 1-6: --------- [#] + [4] + device no. + [#] + [4] + device no. To remotely activate X-10 devices 7 & 8: ----- To remotely deactivate X-10 devices 1-6: ----- [#] + [7] + device no. + [#] + [7] + device no.
SYSTEM OVERVIEW About the Master Keypad General IMPORTANT: If the keypad beeps rapidly upon entering the premises, an alarm has occurred during your absence and an intruder may still be on the premises. LEAVE IMMEDIATELY and CONTACT THE POLICE from a nearby safe location. The keypad allows you to control all system functions.
SYSTEM OVERVIEW Master Keypad Definitions 20 21 3 2 1 4 19 5 18 17 ARMED READY 6 OFF 1 2 3 ESCAPE RECORD VOLUME PLAY AWAY 4 5 6 BYPASS ADD LIGHTS ON TEST STAY 7 8 9 DELETE LIGHTS OFF CODE CHIME * 0 # NO DELAY FUNCTION AUX SELECT STATUS 7 8 9 16 15 14 13 11 12 10 01009-022-V1 IMPORTANT! When you use the keypad to enter codes and commands, press the keys within 2 seconds of one another.
SYSTEM OVERVIEW Master Keypad Definitions 5. TEST 6. BYPASS CODE KEY: Removes individual protection KEY: Allows entry of additional user codes that can be given to other system users. 8. CHIME 16. AWAY KEY: Turns the Chime mode on and 9. INTERNAL SOUNDER: Source of alarm sounds (see "Summary of Audible Notifications" section). KEY: Allows alternate key 17. OFF functions. It is used as a “repeat” key during Clock/Calendar setting. 11.
SYSTEM OVERVIEW About the Display and Indicators AWAY Display Definitions (for other displays, see Trouble Messages) ALARM: AWAY: INSTANT: STAY: UL LOW BAT AC INSTANT CHIME TEST ALARM STAY REC MESSAGE FIRE BYPASS FAULT Appears when the system is armed and an intrusion has been detected (also appears during a fire alarm or audible emergency alarm). Accompanied by the protection zone that is in alarm. All burglary zones, interior and perimeter, are armed. Entry delay is turned off.
SECURING THE PREMISES Checking System Status General Information Before arming your system, all protected doors, windows, and other protection zones must be closed or bypassed (see the BYPASSING PROTECTION section). Pressing the STATUS key will announce all zones that are faulted, as well as any other abnormal system condition, making it easier for you to secure any open zones. READY LIGHT: The green READY indicator on the keypad will be lit if the system is ready to be armed.
SECURING THE PREMISES Arming the System Arming in Stay Mode Use this mode when you are staying home, but expect someone to use the entrance door later. Close all protected perimeter windows and doors before arming. The green READY indicator on the keypad should be lit if the system is ready to be armed. + STAY To arm in STAY mode: or press and hold STAY ** Your User code** ** See Quick Arming paragraph. The keypad beeps three times and displays the armed STAY message.
SECURING THE PREMISES Arming the System Arming the System With No Delay Use NO DELAY with STAY mode when you are staying home and do not expect anyone to use the entrance door. Use NO DELAY with AWAY mode when the premises will be vacant for extended periods of time such as vacations, etc. When armed with NO DELAY, the system will sound an alarm if a protected door or window is opened, including the entrance door.
SECURING THE PREMISES Entry/Exit Delays Exit Delay Exit delay begins immediately after arming the system, and gives you time to leave through the designated exit door without setting off an alarm. A slow beeping will sound throughout the exit delay period, if programmed. Exit Alarms Exit Alarm Active To minimize false alarms sent to the alarm monitoring company, your system may have been programmed for this feature. Ask your installer if Exit Alarm is active for your system.
SECURING THE PREMISES Disarming the System Use the OFF key to disarm the system and to silence alarm and trouble sounds. See the SUMMARY OF AUDIBLE NOTIFICATION section for information, which will help you to distinguish between fire and burglary alarm sounds. IMPORTANT: If you return and the main burglary sounder is on, DO NOT enter the premises, but call the police from a nearby safe location.
SECURING THE PREMISES Bypassing Protection Zones Bypassing Individual Zones Use the BYPASS key when you want to arm your system with one or more zones intentionally unprotected. Bypassed zones are unprotected and will not cause an alarm when violated while your system is armed. All bypasses are removed when an OFF sequence (security code plus OFF) is performed. Bypasses are also removed if the arming procedure that follows the bypass command is not successful.
SECURING THE PREMISES Panic Keys / Chime Mode Panic Keys Your system may have been programmed to use special keys to manually activate panic functions. The functions that might be programmed are listed below. See your installer for the function(s) that may have been programmed for your system. Active Panic Functions Your installer should note the functions that are active in your system.
USER FUNCTIONS Paging Feature Automatic Paging If the Paging feature has been programmed for your system, your pager will respond to certain conditions as they occur in your system by displaying a message that indicates the type of condition that has occurred. The message appears in a 7-digit format explained below. The system can also be programmed to send up to 16 additional digits that will appear in front of the 7-digit message.
USER FUNCTIONS “Follow Me” Announcement Feature “Follow Me” Reminder and System Announcements If the “Follow Me” Announcement feature has been programmed your system will automatically dial a telephone number and deliver a voice message. The two different types of “Follow Me” messages include system and reminder announcements.
USER FUNCTIONS “Follow Me” Announcement Feature NOTES: (1) (2) The “Follow Me” announcement will be terminated if any new report needs to be sent or if any key is pressed on the LYNXR-EN keypad or a wireless (RF) keypad. The [✻] key on a wireless keypad is ignored by the system when the “Follow me” feature is active and cannot be used to terminate the announcement or request status.
USER FUNCTIONS Using Powerline Carrier Device Commands (Lights On/Lights Off Keys) General Information Powerline Carrier devices (e.g. X-10 brand devices) are programmable switches that can be used to perform many different functions. Your system may be set up so that certain lights or other devices can be turned on or off by using the device command from the keypad. Ask your installer if this has been done in your system.
USER FUNCTIONS Message Recording/Playback/Volume Control The LYNXR-EN Message Center allows you to record, play and delete messages. The maximum message duration is 85 seconds. NOTES: (1) (2) (3) (4) The Record/playback functions can only be performed from the master keypad. It cannot be performed from any other wireless keypad (ex. 5827). If the system loses electrical power, all messages will be erased. Message Play/Record will not be available if a report must be sent.
USER FUNCTIONS Message Recording/Playback/Volume Control Adjusting the Volume The volume level of message playback, system announcements, and status beeps can be changed. You can also mute system announcements if desired. See NOTE below if using a wireless keypad. To adjust message playback/system announcement volume: FUNCTION + VOLUME + [3] or [6] † † [3] = increases volume one level, [6] = decreases volume one level. Repeat the key sequence until the desired volume level is achieved.
USER FUNCTIONS AUX Function General Information The AUX key may have been programmed to either perform a predefined function or to send a preset message to a pager/”Follow Me” system phone number (see Pager Feature section for pager operation or the Follow Me Announcement Feature section for “Follow Me” operation). Ask your installer which function has been assigned for your system.
USER FUNCTIONS Clock/Calendar Your system can display the current time (see your installer). The date is not displayed, but has an internal function. The system must be disarmed. + FUNCTION To set the time and date: + [63] Master user code or Installer Code The system will enter the Voice Prompt Calendar Setting mode. The [#] key can be pressed at any time to repeat a voice prompt. NOTES: 1. The keypad beeps twice for invalid data entries (e.g.
USER FUNCTIONS Clock/Calendar 5. The system will announce, “Enter two-digit day press ADD to accept, ESCAPE to quit”. Day 01 (The current day of the month will display.) Enter the 2-digit day of the month (i.e., 01-31). Press [ADD] to accept the entry and continue to the year setting. Press [ESCAPE] to back up to Month selection. 6. The system will announce, “Enter two-digit year press ADD to accept, ESCAPE to quit”. Year 02 (The current year will be displayed.
USER FUNCTIONS Scheduling User Interface + FUNCTION + [64] To access the Scheduling User Interface enter: Master user code or Installer Code The following entries will be sequentially prompted to the user. Note that all inputs are checked for validity upon entry and all invalid entries are rejected. Hitting a [*] will allow the entries to be accepted and advance to the next field. Hitting a [#] will reject the entry and back up one field.
USER FUNCTIONS Scheduling User Interface NOTE: The keypad beeps twice for invalid data entries (e.g.: an hour greater than 12), and the entry will not be accepted. The keypad beeps once for valid entries and four times when a schedule event is programmed successfully. [x] = the value that was last stored in the memory.
USER FUNCTIONS Scheduling User Interface b : xx xx : bd Begin Time (minute) [xx] = begin minute 0 to 59 [*] = continue [#] = return to previous prompt Begin Day [xx] = begin day 01 to 17 [*] = continue [#] = return to previous prompt • If the value programmed in the Event Identifier is “3”, “4”, or “5”, and the current entry is completed, the system will save all field data up to this field. The system will beep four times and go back to the first field (Schedule Number) with the schedule number advanced.
USER FUNCTIONS Scheduling User Interface Event Identifier Entries Entry 0 Event Empty Comment No event scheduled (or schedule is temporarily disabled) 1 X-10 Device Turn an X-10 device, either on or off at begin/end times. (will have a start and end time to program) (time driven) NOTE: SH10A siren cannot be used. 2 Latch Key Report Send a special pager report (7110000) indicating system not yet disarmed.
USER FUNCTIONS Scheduling User Interface Day of Week Entries Entry 00 Day Invalid day entry 01 Do event on next time match on the next Monday (will remove itself after executing) 02 Do event on next time match on the next Tuesday (will remove itself after executing) 03 Do event on next time match on the next Wednesday (will remove itself after executing) 04 Do event on next time match on the next Thursday (will remove itself after executing) 05 Do event on next time match on the next Friday (will
USER FUNCTIONS Remote Phone Control Feature The LYNXR-Series is equipped with a remote interactive phone capability that permits access to the security system from any off-site touch-tone telephone using all user codes. If this feature has been programmed, the system will provide the appropriate voice messages and any system beeping sounds indicating the status of the security system over the phone line. (Refer to Summary of Audible Notification for further information.
USER FUNCTIONS Remote Phone Control Feature (within eight seconds) Enter: Your user code Upon entering remote phone control mode the Lynx will announce “System, enter code”. Remote Phone Control Commands + [1] To remotely disarm system: Your user code + [2] To remotely arm in AWAY mode: Your user code + [3] To remotely arm in STAY mode: Your user code + [2] or [3] + [0] To remotely arm in AWAY or STAY mode with no delay: Your user code To remotely activate X-10 devices 1-6: [#] + [4] + device no.
USER FUNCTIONS Speaker Phone Feature If this feature has been programmed the LYNXR-EN is capable of operating as a speaker phone. During speaker phone operation the system will provide the following functions: • All function/event processing will continue to operate, but there will be no announcements. • The ARMED (red) and READY (green) LEDs will alternately blink. • “PH” will be displayed. NOTE: The system will enter the Speaker phone mode even if an alarm or trouble is stored in the system memory.
USER FUNCTIONS Speaker Phone Feature LYNXR-EN Speaker Phone Functions To place a call using the Speaker Phone: [#] + AUX and dial the desired phone number. To answer a call using the Speaker Phone: [#] + AUX To flash (switch between two calls using call waiting): AUX To hang up: OFF To activate/deactivate (toggle) ringer: [#] + VOLUME + AUX NOTE If you are using pulse (rotary) dialing, make sure that LYNXREN has finished dialing the last digit you dialed, (listen to pulses) before dialing the next digit.
FIRE ALARM SYSTEM SYSTEM (If Installed) General Information UL LYNXR-EN is not intended for UL985 Household Fire applications unless a 24-hour backup battery (P/N LYNXRCHKIT-HC) is installed. General Your fire alarm system (if installed) is active 24 hours a day, providing continuous protection. In the event of an emergency, the installed smoke and heat detectors will automatically activate your security system, triggering a loud, intermittent sound from the keypad.
FIRE ALARM SYSTEM National Fire Protection Association’s Smoke Detector Recommendations UL LYNXR-EN is not intended for UL985 Household Fire applications unless a 24-hour backup battery (P/N LYNXRCHKIT-HC) is installed. With regard to the number and placement of smoke and heat detectors, we subscribe to the recommendations contained in the National Fire Protection Association's (NFPA) Standard #74 noted below.
FIRE ALARM SYSTEM Emergency Evacuation UL LYNXR-EN is not intended for UL985 Household Fire applications unless a 24-hour backup battery (P/N LYNXRCHKIT-HC) is installed. Establish and regularly practice a plan of escape in the event of fire. The following steps are recommended by the National Fire Protection Association: Position your detector or your interior and/or exterior sounders so that they can be heard by all occupants. 2. Determine two means of escape from each room.
SYSTEM FUNCTIONS Security Codes General Information For additional security you (the Master User Code) can assign secondary user codes to individual users enabling them to perform specific system functions. These secondary users are identified by "user numbers" when their codes are assigned. You can assign up to 6 user codes (2-digit user numbers 0308). Note that the master user is the only one who can assign codes to secondary users, and is designated user no. 02; user no. 01 is the Installer’s code.
SYSTEM FUNCTIONS Testing the System (to be conducted weekly) Entering Test Mode The TEST key puts your system into the Test mode, which allows each protection point to be checked for proper operation. The keypad sounds a single beep every 45 seconds as a reminder that the system is in the Test mode. NOTE: An alarm message will not be sent to your alarm monitoring company during the following tests. Disarm the system and close all protected windows, doors, etc. The “READY” indicator should be lit.
SYSTEM FUNCTIONS Trouble Messages Typical Trouble Condition Displays To silence the beeping sound for fault conditions, press any key. FAULT FC CC dI CA EA 90 93 LOW BAT Indicates that a problem exists with the zone(s) displayed, accompanied by rapid beeping. First, determine if the zone(s) displayed are intact and make them so if they are not. If the zone uses a wireless detector, check that changes in the room (moving furniture, televisions, etc.) are not blocking wireless signals from the detector.
SYSTEM FUNCTIONS Maintaining your system The components of your security system are designed to be as maintenance-free as possible. To make sure that your system is in working condition, do the following: 1. Test your system weekly. 2. Test your system after any alarm occurs (see the TESTING THE SYSTEM section). Low Battery Conditions in Wireless Sensors Each wireless sensor in your system has a 9-volt or 3-volt battery.
Summary Of Audible Notificat Notification ion *UPPER CASE indicates announcements after pressing STATUS once. Lower case indicates announcements after pressing STATUS twice. SOUND CAUSE DISPLAY ANNOUNCEMENT* FIRE ALARM FIRE ALARM is displayed; zone fire alarm + zone voice INTERRUPTED number in alarm displayed.
Summary Summary Of Audible Notification Additional Announcements: Pressing STATUS key once will announce the following primary messages, depending on the system’s status at the time: Disarmed–Ready to Arm [check system] Disarmed [not ready to arm] Armed [away] [stay] [instant] [check system] [exit now] Pressing the STATUS key twice will announce the following secondary messages, depending on the system’s status at the time: Fire Alarm + zone voice descriptor Alarm + zone voice descriptor Fire Fault + zone v
UL NOTICE: This is a "Grade A" residential system. FCC ID: CFS8DLLYNXREN-2 CANADA: 1748A-LYNXREN-2 FCC STATEMENT THIS DEVICE COMPLIES WITH PART 15 OF FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
Federal Communications Commission (FCC) Part 68 This equipment complies with Part 68 of the FCC rules and the requirements adopted by ACTA. On the front cover of this equipment is a label that contains the FCC registration number and Ringer Equivalence Number (REN). You must provide this information to the telephone company when requested. This equipment uses the following USOC jack: RJ31X This equipment may not be used on telephone-company-provided coin service.
IN THE EVENT OF TELEPHONE OPERATIONAL PROBLEMS In the event of telephone operational problems, disconnect the control by removing the plug from the RJ31X (CA38A in Canada) telephone wall jack. We recommend that your certified installer demonstrate disconnecting the phones on installation of the system. Do not disconnect the phone connection inside the control/communicator. Doing so will result in the loss of your phone lines.
SERVICING INFORMATION Your local Honeywell dealer is the person best qualified to service your alarm system. Arranging some kind of regular service program with him is advisable.
OWNER'S INSURANCE PREMIUM CREDIT REQUEST This form should be completed and forwarded to your homeowner's insurance carrier for possible premium credit. A. GENERAL INFORMATION: Insured's Name and Address: Insurance Company: Policy No.: ADEMCO LYNXR-EN Type of Alarm: ______________________________________ Other Burglary Fire Installed by: Both Serviced by: Name Name Address Address B. NOTIFIES (Insert B = Burglary, F = Fire) Local Sounding Device Central Station Police Dept. Fire Dept.
OWNER'S INSURANCE PREMIUM CREDIT REQUEST (cont.) E. SMOKE DETECTOR LOCATIONS Furnace Room Kitchen Bedrooms Attic Basement Living Room Dining Room Hall All Exterior Doors F. BURGLARY DETECTING DEVICE LOCATIONS: Front Door Basement Door Rear Door 1st Floor Windows All Windows Interior Locations All Accessible Openings, Including Skylights, Air Conditioners and Vents G.
INDEX A AC...................................................................12 Adjusting the volume.....................................25 Alarm .........................................................5, 12 Alarm monitoring company...........................19 Armed indicator .............................................10 Audible emergency/audible alarm ................19 Aux function...............................................8, 26 Aux key function ..............................................
P Pager ..........................................................8, 26 Pager Code .....................................................20 Paging feature..................................3, 20, 2, 26 Panic key ....................................................3, 19 Personal emergency/aux. alarm....................19 Phone access feature................................34, 36 Phone control ...................................................4 Play back a message ........................................
WARNING! THE LIMITATIONS OF THIS ALARM SYSTEM While this system is an advanced design security system, it does not offer guaranteed protection against burglary or fire or other emergency. Any alarm system, whether commercial or residential, is subject to compromise or failure to warn for a variety of reasons. For example: • Intruders may gain access through unprotected openings or have the technical sophistication to bypass an alarm sensor or disconnect an alarm warning device. • Intrusion detectors (e.g.
ONE YEAR LIMITED WARRANTY Honeywell International Inc., acting through its Security & Custom Electronics business ("Seller"), 165 Eileen Way, Syosset, New York 11791, warrants its security equipment (the "product") to be free from defects in materials and workmanship for one year from date of original purchase, under normal use and service.
NOTES – 59 –
NOTES – 60 –
NOTES – 61 –
NOTES – 62 –
– 63 –
165 Eileen Way, Syosset, New York 11791 ‡K5963V3oŠ K5964V3bx 5/04 Rev. A Copyright © 2004 Honeywell International Inc. www.honeywell.
