：PL10W
Technical data .................................................................................................3 Introduction ....................................................................................................4 Safety information .......................................................................................... 4 General safety rules ........................................................................................5 Special safety rules for cordless impact wren.
ThankYou for Purchasing a ADEDAD Product.This manual provides information regarding the safe operation and maintenance of this product.Every effort has been made to ensure the accuracy of the information in this manual. ADEDAD reserves the right to change this product and specifications at anytime without prior notice. Please keep this manual available to all users during the entire life of the powertool.
Safety is a combination of common sense, staying alert, and knowing how your power tool works. . Do not operate this unit until you read this instruction manual for safety, operation and maintenance instructions. Failure to follow all instructions listed below may result in electric shock, fire, and/or serious personal injury. Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.
Do not force power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it is designed. Do not use the power tool if switch does not turn it on or off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. Disconnect the plug from the power source before making any adjustments, changing accessories, or storing the power tool.
Hold power tools by insulated gripping surfaces when performing an operation where the cutting tools may contact hidden wiring. Fasteners contacting a "live" wire may make exposed metal parts of the power tool "live" and could give the operator an electric shock. Wear ear protectors with. Exposure to noise can cause hearing loss. Check the impact socket carefully for wear, cracks or damage before installation. Hold the tool firmly. Keep hands away from rotating parts. Always be sure you have a firm footing.
Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the product better and safer. SYMBOL NAME Volts Amperes Hz Hertz Watts MIN Minutes Safety Alert DESIGNATION/EXPLANATION Voltage Current Frequency (cycles per second) Power Time Precautions that involve your safety.
1 4 2 3 5 7 6 1 3 5 Square drive anvil Trigger switch Handle 2 Worklight 4 Forward/Reversing lever & trigger lock 6 Battery 7 Battery capacity display and Reverse stop Unpack the power tool and all its parts, and compare against the list below. Do not discard the carton or any packaging materials. Please call 1-800-791-9458 or E-mail us at support@amerisuninc.com if any parts are damaged or missing.
Do not use this product if any parts on the packing list are already assembled to your product when you unpack it. Parts on this list are not assembled to the product by the manufacturer and require customer installation. Use of a product that may have been improperly assembled could result in serious personal injury. If any parts are damaged or missing do not operate this product until the parts are replaced. Use of this product with damaged or missing parts could result in serious personal injury.
: Always be sure that the tool is switched off and the battery cartridge is removed before carrying out any work on the tool. Align the belt hook with the mounting hole of the base and tighten the screw. The belt hook can be installed from the other side according to the operation habit. The battery pack is not charged when it is purchased. Before using the power tool for the first time, place the battery pack in the battery charger and charge.
After tool use, lock trigger in “OFF” position to help prevent accidental starts and accidental discharge. Your tool is equipped with a forward/ reversing lever and trigger lock located above the trigger (fig. 1). This lever was designed for changing rotation of the bit, and for locking the trigger in an “OFF” position. For forward rotation, (with chuck pointed away from you) move the lever to the far left. For reverse rotation move the lever to the far right.
When the temperature of battery is too high and the machine switches off automatically. • Switch the power tool off. • Allow the battery to cool down before continuing to work. When the power tool is blocked and switches off automatically. • Remove the power tool from the workpiece. • As soon as the blockage is corrected, the power tool will continue to work at the set stroke rate. Battery packs are shipped in a low charge condition to prevent possible problems.
Read instruction manual first! Remove battery pack from the tool before making adjustments or assembling accessories. 1. Battery pack not charged. 2. Battery pack not installed properly. 3. Battery pack temperature is too hot or cold for operation. 4. Burned out switch. 1. If equipped, check battery charge condition lights for charge status. Charge battery if needed. 2. Confirm battery is locked and secured to the tool. 3. Let battery sit a few minutes or until it reaches normal operating temperature. 4.
For questions / comments, technical assistance or repair parts – Please send 15
