Table of Contents Optical Time Domain Reflectometers (OTDRs) and Fault Locators C850 Compact QUAD OTDR with QUAD OLS and OPM . . . . . . . . . 3 M700 Compact Single-mode OTDR . . . . . . . . . . . . . . . . . . . . . . . 7 M650 Compact QUAD OTDR . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 M200 Handheld OTDR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 OFL 280 Handheld FTTx OTDR. . . . . . . . . . . . . . . . . . . . . . . . . . 15 OFL 250 Handheld Single-mode OTDR. . . . .
DFS1 Digital FiberScope The DFS1 Digital FiberScope supports magnified video inspection of optical fiber connector end-faces during fiber optic cable and connector installation and maintenance. The ergonomically designed hand-held unit illuminates fiber end-faces and delivers magnified images via USB port to AFL’s M-series OTDRs (M200, M700) or C-series OTDRs and Certification Testers (C840, C850, C860, C880).
C850 Compact QUAD OTDR with QUAD OLS and OPM Features The Noyes C850 from AFL Telecommunications is a full-featured QUAD OTDR in a compact case with a large transflective touch screen display suitable for both indoor and outdoor operation. The C850 offers built-in auto test functionality when used with another C850 or the C840 QUAD Certification Tester.
C850 Compact QUAD OTDR with QUAD OLS and OPM Ordering Information The C850 OTDR Kits and Options allow users to buy the test equipment functionality needed today and grow to meet the demands of certification testing. The C850 combined with an OLS 4 source will allow users to test and generate detailed reports with both OTDR and Loss results shown for each fiber and in charts by cable. Users can add a C840 or another C850 to perform Certification testing.
C850 Compact QUAD OTDR with QUAD OLS and OPM Ordering Information (continued) Each C850 kit includes the C850 OTDR, USB Flash drive, PC software for OTDR trace analysis and certification or OPM loss reporting, AC adapter, switchable test ports adapters and accessories (see table below).
C850 Compact QUAD OTDR with QUAD OLS and OPM Specifications (All specifications valid at 25°C unless otherwise specified) OTDR Multimode Single-mode Emitter Type Laser Safety Class Class I FDA 21 CFR 1040.10 and 1040.11, IEC 60825-1: 2007-03 Center Wavelengths Wavelength Tolerance 850/1300 nm 1310/1550 nm ± 20/30 nm ± 20/30 nm 22 dB 26 dB Dynamic Range (SNR = 1) 10, 30, 100, 300 ns; 1, 3, 10 ms Pulse Widths Range Settings 250 m to 64 km Sampling Points 250 m to 208 km 0.
M700 Compact Single-mode OTDR The Noyes M700 from AFL Telecommunications is a compact, full-featured, single-mode OTDR that includes an integrated Visual Fault Locator (VFL), an Optical Power Meter (OPM) capable of displaying up to three wavelengths simultaneously, and a large transflective touch screen display suitable for both indoor and outdoor operation.
M700 Compact Single-mode OTDR Specifications Power Meter OTDR Emitter Type Laser Safety Class Class I FDA 21 CFR 1040.10 and 1040.11, IEC 60825-1: 2007-03 Center Wavelengths 1310/1550 nm Dynamic Range (SNR = 1) 38/36 dB (1310/1550 nm) Accuracy Event Dead Zone 1 0.9 m Measurement Units dB, dBm, mW Attenuation Dead Zone 2 4.
M650 Compact QUAD OTDR Features •• 22 dB (MM), 26 dB (SM) dynamic range •• Integrated OPM and VFL (650 nm) •• Full Auto, Expert, and Real-Time OTDR test modes •• 6.5-inch transflective (indoor/outdoor) touch screen display •• Tool-free, switchable test port adapters •• Rechargeable Li-Ion battery (> 8 hours) or AC power •• USB host and function ports •• Bellcore (GR-196) .
M650 Compact QUAD OTDR M650-100-LP1-S1 Kit M650-100-LP1-H2 (or H5) Kit Ordering Information When placing an order, select options as follows: Model, Optical Configuration, Language, and Case.
M650 Compact QUAD OTDR Ordering Information (continued) Combining the M650 with an OLS 4 source will allow users to test and generate detailed reports with both OTDR and Loss results shown for each fiber and in charts by cable. Kit model number carry Case and Accessories Each M650 kit includes the M650 OTDR, USB Flash drive, PC software for OTDR trace analysis and OPM loss reporting, AC adapter, switchable test ports adapters, and accessories (see table below).
M650 Compact QUAD OTDR Specifications (All specifications valid at 25°C unless otherwise specified) OTDR Multimode Single-mode Emitter Type Laser Safety Class Class I FDA 21 CFR 1040.10 and 1040.
M200 Handheld OTDR The Noyes M200 from AFL Telecommunications offers unmatched OTDR capabilities in a handheld package weighing less than 1 kg (2 lb). Multimode, Single-mode, and ‘Quad’ wavelength models are offered. With short dead zone and intermediate range specifications, the M200 is ideal for Tier 2 testing of premises (building and campus) networks or certification and troubleshooting of FTTX PON networks. And its bright, transflective display makes it suitable for both indoor and outdoor operation.
M200 Handheld OTDR in a Hard Case The Noyes M200 OTDR is also available in a tough injection molded ABS carrying case. The rugged transit case has a full length hinge, padlock loops, secure snap latches and an O-ring seal to protect the contents from dust and water. In addition to the OTDR, the custom case has room for cleaning products, launch and receive rings, documentation and more. Order the Hard Case alone or with one of the M200 configurations.
M200 Handheld OTDR Specifications OTDR Specifications Multimode Single-mode Emitter Type Laser Safety Class Class I FDA 21 CFR 1040.10 and 1040.11, IEC 60825-1:2007-03 Center Wavelengths 850/1300 nm 1310/1550 nm Wavelength Tolerance ± 20/± 30 nm ± 20/± 30 nm Dynamic Range (SNR = 1) 22 dB 26 dB Event Dead Zone 1 1.5 m 1.
OFL280 Handheld FTTx OTDR Installation (Live Fiber) and Construction Models The Noyes OFL280 from AFL Telecommunications is a singlemode OTDR offered in two FTTx-optimized models. The ‘installation and repair’ model can operate at three wavelengths (1310/1550/1625 nm) on dark fibers but automatically switches to a filtered, 1625 nm only mode if a live fiber is detected.
OFL280 Handheld FTTx OTDR Ordering Information Two OFL280 models are available as indicated below: Model WAVELENGTHS Description OFL280-102 1310/1490/1550 (nm) FTTx construction OTDR Measures loss at the (3) wavelengths used in FTTx PON networks. OFL280-103 1310/1550/1625 (nm) FTTx installation (live fiber) OTDR Includes filter to test live FTTx fibers @ 1625 nm, and a PON power meter to measure downstream (1490/1550 nm) power levels on FTTx networks.
OFL280 Handheld FTTx OTDR Specifications (All specifications valid at 25°C unless otherwise specified) OTDR Optical Power Meter Emitter Type Laser Calibrated Wavelengths 1310, 1490, 1550, 1625, 1650 nm Safety Class Class I FDA 21 CFR 1040.10 and 1040.
OFL 250 Handheld OTDR The Noyes OFL 250 from AFL Telecommunications is a single-mode OTDR with an integrated Optical Power Meter (OPM), Laser Source (OLS), and Visual Fault Locator (VFL) in a handheld package weighing only 0.8 kg (1.7 lb). With short dead zone and mid-range dynamic range performance, the OFL 250 is ideal for testing optical fibers in service provider metro areas and FTTx networks.
OFL 250 Handheld OTDR Specifications OTDR Optical Light Source Emitter Type Laser Safety Class Class I FDA 21 CFR 1040.10 and 1040.11, IEC 60825-1: 2007-03 Fiber Type Single-mode Center Wavelengths 1310/1550/1625 nm Wavelength Tolerance ± 20 / ± 20 / ± 10 nm Wavelength Tolerance ± 20/± 20/± 10 nm Spectral Width (FWHM) 5 nm (max) Dynamic Range (SNR=1) 26/26/26 dB Internal Modulation 1 kHz, 2 kHz Event Dead Zone 1.
OTDR Fiber Rings Measuring an insertion loss of the near-end and / or far-end connection of a fiber optic link with an OTDR requires a launch and / or receive test cable. A launch cable, which connects the OTDR to the link under test, reveals the insertion loss and reflectance of the near-end connection. A receive cable, which connects to the far-end of the link, reveals the insertion loss and reflectance of the far-end connection.
OTDR Fiber Rings How to Generate a Baseline Trace Using Fiber Rings •• Use the Fiber Ring as a launch cable. Connect the Fiber Ring between your OTDR and the fiber link under test. This will allow you to measure the loss of the near-end connection. •• Use the Fiber Ring as a receive cable. Cconnect the Fiber Ring to the far-end connector of your fiber link under test. This will allow you measure the loss of the far-end connection.
C860 QUAD OTDR and Certification Test Kit Features The Noyes C860 QUAD Certification and OTDR Test Kit from AFL Telecommunications includes one handheld C840 QUAD OLTS Tester and one C850 QUAD OTDR/OLTS with built-in auto test functionality. With this kit, technicians can troubleshoot and perform both Tier 1 and Tier 2 certification tests of MM and SM fiber networks, store results and create professional test reports.
C860 QUAD OTDR and Certification Test Kit The C840 and C850 can be used together to perform Tier 1 dual wavelength MM (850/1300 nm) and SM (1310/1550 nm) auto loss tests of one or two fibers in one or both directions as well as measure both loss and length of the fibers and compare to industry standards (TIA/ISO/EN), applications and user-defined thresholds values to certify the fibers. Either unit can be identified as the Main or Remote.
C860 QUAD OTDR and Certification Test Kit Ordering Information (continued) Each kit includes one handheld C840 QUAD Certification Tester, one compact C850 QUAD OTDR/OLTS, USB Flash drive, PC software for OTDR trace analysis and certification or OPM loss reporting, (2) AC adapters, switchable test ports adapters, and accessories (see table below). Model carry Case Fiber Rings1 Test Cords2 OTDR/OLS Adapters OPM Cleaning Products VFI C860-100-LP1-H2 Soft and hard cases SC/LC SC/LC SC, ST, LC SC, 2.
C860 QUAD OTDR and Certification Test Kit Specifications (All specifications valid at 25°C unless otherwise specified) OTDR Multimode Single-mode Emitter Type Laser Safety Class Class I FDA 21 CFR 1040.10 and 1040.11, IEC 60825-1: 2007-03 Center Wavelengths Wavelength Tolerance 850/1300 nm 1310/1550 nm ± 20/30 nm ± 20/30 nm 22 dB 26 dB Dynamic Range (SNR = 1) 10, 30, 100, 300 ns; 1, 3, 10 ms Pulse Widths Range Settings 250 m to 64 km Sampling Points 250 m to 208 km 0.
FTK Pro Installer Kit The Noyes FTK Pro Installer Kit from AFL Telecommunications provides a wide selection of fiber optic testing, cleaning, and inspection equipment to enable technicians to install and maintain fiber optic networks. Available with multimode and single-mode test equipment, the kit also includes a broad array of cleaning and inspection equipment in a convenient tough injection-molded ABS carrying case.
C880 QUAD Certification Test Kit Features •• Handheld, 0.
C880 QUAD Certification Test Kit Ordering Information Each C880 kit or C840 kit includes two (2) C840s or one (1) C840 Tester respectively, USB Flash drive, PC software for OTDR trace analysis and certification or OPM loss reporting, AC adapters (two (2) with C880 kit, one (1) with C840 kit), switchable test ports adapters, and accessories (see table below). Model carry Case Test Cords2 Adapters Cleaning Products OLS OPM VFI SC, ST, LC SC, 2.5, 1.25mm 2.5, 1.25mm One-Click Cleaner SC/ST/FC, 2.
C880 QUAD Certification Test Kit Specifications (All specifications valid at 25°C unless otherwise specified) General Test Modes Visual Fault Locator Auto Test, OPM, OLS, VFL Emitter Type Laser Length Measurement Range 5 km (MM); 200 km (SM) Safety Class Class II FDA 21 CFR 1040.10 and 1040.11, IEC 60825-1: 2007-03 USB flash drive (2.0) Wavelength 650 nm Downloadable from unit directly to PC Output Power (nominal) 0.
NOYES TurboTest 500B Loss Test Set has been discontinued Turbotest 500B Optical Loss/Return Loss Test Sets The Turbotest 500B Series offers the latest technology in a single fiber bi-directional loss and return loss testing. The T500B is a handheld fiber optic test and measurement instrument. It performs Optical Power, Optical Return Loss, and Optical Loss measurements. Five compact models are available, including the three wavelength (1310/1550/1625) T506B and (1310/1550/1490) T506B-FTTH.
OLTS 5 Optical Loss Test Set The OLTS 5 Optical Loss Test Set series offers end-to-end single-mode testing at either 1310/1550 nm or 1550/1625 nm. The OLTS 5 may be operated in automatic or manual test modes. In its “two-unit” automatic test mode, a pair of OLTS 5 test sets may be used to measure the end-to-end, bi-directional insertion loss of a pair of single-mode fibers at 1310/1550 nm or 1550/1625 nm. Tests are started and controlled by the user from the OLTS 5 configured as the Main unit.
ORL3B Optical Return Loss Test Set The ORL3B is a handheld fiber optic test and measurement instrument that offers two modes of testing. It performs optical return loss measurements (ORL mode) and operates as an optical power meter (OPM mode). The ORL3B can store up to 1000 records (40 files) in any combination of its two operating modes. With the supplied PC software, saved test results can be transferred to a PC for storage, printing, and analysis.
OPM4-FTTx PON Power Meter The Noyes OPM4-FTTx from AFL Telecommunications is designed to measure optical power in FTTH and other passive optical networks (PONs) that use 1490 nm for downstream data and 1550 nm for downstream video traffic. In addition, the OPM4-FTTx provides an integrated Visual Fault Locator (VFL) - 650 nm (red) laser for short-range fault location and connectivity testing.
OPM5 Optical Power Meter The OPM5 from AFL Telecommunications is a full-featured, handheld optical power meter designed for measuring optical power in Premises, Telco, or Broadband networks and for performing insertion loss measurements on multimode or single-mode fiber optic links.
OPM4 Optical Power Meter The Noyes OPM4 from AFL Telecommunications is a handheld optical power meter designed for measuring optical power in Premises, Telco, or Broadband networks and for performing insertion loss measurements on multimode or single-mode fiber optic links.
OPM1 Optical Power Meter This portable optical power meter may be used to measure optical power in premises, telco, or broadband fiber optic networks. When used with an LED or laser light source, the OPM1 can also measure the attenuation (insertion loss) of multimode or single-mode cables. With only two controls – ON/OFF and wavelength – the OPM1 is our simplest to use optical power meter. Optical power in dBm and the calibration wavelength setting are displayed on an easy-to-read LCD display.
CSM1 Contractor Series Optical Power Meter The Noyes CSM1 from AFL Telecommunications is a palm-sized, cost-effective optical power meter designed for measuring optical power in Premises, Telco, or Broadband fiber optic networks and for performing insertion loss measurements on multimode or singlemode fiber optic links. Weighing only 0.4 lb, this power meter is ideal for field use.
OLS7-FTTH & OLS7-3 Triple Wavelength Laser Sources The OLS7-FTTH and OLS7-3 from AFL Telecommunications are handheld, rugged laser sources designed for performing insertion loss measurements on single-mode fiber optic links when used with an optical power meter. When paired with an optical fiber identifier, both models may be used for fiber identification. The LASER output is stabilized to ensure accurate test results per current TIA/EIA requirements.
OLS4 Integrated Laser and LED Source The OLS4 from AFL Telecommunication is a handheld, rugged, integrated two-port LED and LASER light source designed for performing insertion loss measurements on multimode or single-mode fiber optic links when used with an optical power meter. When paired with an optical fiber identifier, the OLS4 may be used for fiber identification. The LED and LASER outputs are stabilized to ensure accurate test results per current TIA/EIA requirements.
OLS2-Dual Laser Light Source The OLS2-Dual from AFL Telecommunications is a handheld, rugged laser source designed for performing insertion loss measurements on single-mode fiber optic links when used with an optical power meter. When paired with an optical fiber identifier, the OLS2-Dual may be used for fiber identification. The LASER output is stabilized to ensure accurate test results per current TIA/EIA requirements.
OLS1-Dual LED Light Source The OLS1-Dual from AFL Telecommunication is a handheld, rugged LED light source designed for performing insertion loss measurements on multimode fiber optic links when used with an optical power meter. The LED output is stabilized to ensure accurate test results per current TIA/EIA requirements. The OLS1-Dual features 850 nm and 1300 nm LED output from a single output port and is easy to operate with only a power button and a wavelength select button.
OLS1 LED Light Source The OLS1 LED light source is a cost-effective, rugged, handheld instrument designed for performing insertion loss measurements on fiber optic links when used with an optical power meter. The LED output is stabilized to ensure accurate test results per current TIA/EIA requirements. The OLS1 is easy to operate with only a [Wavelength/ Power] switch, which selects optical wavelengths or disables unit ( position).
CSS1-SM Contractor Series Dual Laser Light Source The Noyes CSS1-SM from AFL Telecommunications is a palm-sized, cost-effective dual LASER source designed for performing insertion loss measurements on single-mode fiber optic links when used with an optical power meter. When paired with an optical fiber identifier, the CSS1-SM may be used for fiber identification. The LASER output is stabilized to ensure accurate test results per current TIA/EIA requirements. Weighing only 0.
CSS1-MM Contractor Series Dual LED Light Source The Noyes CSS1-MM from AFL Telecommunications is a palm-sized, cost-effective dual LED light source designed for performing insertion loss measurements on multimode fiber optic links when used with an optical power meter. When paired with an optical fiber identifier, the CSS1-MM may be used for fiber identification. The LED output is stabilized to ensure accurate test results per current TIA/EIA requirements. Weighing only 0.
SMLP5-5 Single-mode/Multimode Test Kit with Wave ID, Set Reference, and Data Storage The SMLP5-5 test kit combines the OPM5-2D optical power meter and OLS4 integrated LED and LASER light source and is ideally suited for testing fiber optic networks with hybrid (single-mode and multimode) cables.
SMLP5-5 Single-mode/Multimode Test Kit with Wave ID, Set Reference, and Data Storage OLS4 Light Source specifications Optical Wavelength Emitter type Spectral width Output power Output Stability MM Optical Port SM Optical Port 850 ± 30 nm 1300 -10/+50 nm 1310 ± 20 nm 1550 ± 20 nm LED Laser Class I FDA 21 CFR 1040.10 and 1040.11, IEC 60825-1: 2007-03 40 nm (typ) 120 nm (typ) 5 nm (max) 5 nm (max) 0 dBm, 9 µm single-mode > - 20 dBm, 62.5 µm multimode* ± 0.1 dB over 8 hours ± 0.
SMLP4-4 Single-mode/Multimode Test Kit with Wave ID and Set Reference The SMLP4-4 test kit combines the OPM4-2D optical power meter and OLS4 integrated LED and LASER light source and is ideally suited for testing fiber optic networks with hybrid (single-mode and multimode) cables.
SMLP4-4 Single-mode/Multimode Test Kit with Wave ID and Set Reference OLS4 Light Source specifications Optical Wavelength Emitter type Spectral width Output power Output Stability MM Optical Port SM Optical Port 850 ± 30 nm 1300 -10/+50 nm 1310 ± 20 nm 1550 ± 20 nm LED Laser Class I FDA 21 CFR 1040.10 and 1040.11, IEC 60825-1: 2007-03 40 nm (typ) 120 nm (typ) 5 nm (max) 5 nm (max) 0 dBm, 9 µm single-mode > - 20 dBm, 62.5 µm multimode* ± 0.1 dB over 8 hours ± 0.05 dB over 1 hour (after 15 min.
SLP5 Triple Wave Test Kits with Wave ID, Set Reference, and Data Storage The SLP5 triple wavelength single-mode test kits are available in two models, SLP5-FTTH and SLP5-7. The SLP5-FTTH and SLP5-7 model combine the OPM5-4D optical power meter and either OLS7-FTTH (1310/1490/1550 nm) or OLS7-3 (1310/1550/1625 nm) LASER source respectively.
SLP5 Triple Wave Test Kits with Wave ID, Set Reference, and Data Storage OLS7 Specifications Optical Wavelength (±20 nm) Emitter type Spectral width Output power Output stability Tone output General Model OLS7-FTTH Model OLS7-3 1310 nm 1490 nm 1550 nm 1310 nm 1550 nm 1625 nm Laser, Class I FDA 21 CFR 1040.10 and 1040.11, IEC 60825-1: 2007-03 5 nm 3 nm 5 nm 5 nm 5 nm 2 nm -5 dBm (typical) into 9/125 fiber ± 0.05 dB over 1 hour (after 15 min warm-up, after 30 sec typical) ± 0.
SLP5-6D Single-mode Test Kit with Wave ID, Set Reference, and Data Storage The SLP5-6D test kit combines the OPM5-4D optical power meter and OLS2-Dual LASER light source and is ideally suited for testing single-mode fiber optic networks.
SLP5-6D Single-mode Test Kit with Wave ID, Set Reference, and Data Storage OLS2-Dual specifications Optical OLS2-Dual (single port) Wavelength Emitter type 1310 ±20 nm 1550 ±20 nm Laser, Class I FDA 21 CFR 1040.10 and 1040.11, IEC 60825-1: 2007-03 Spectral width (FWHM) 5 nm (max) Output power 0 dBm* Output stability ± 0.05 dB over 1 hour (after 15 min. warm-up) ± 0.1 dB over 8 hours (after 15 min.
SLP4 Triple Wave Test Kits with Wave ID and Set Reference The SLP4 triple wavelength single-mode test kits are available in two models, SLP4-FTTH and SLP4-7. The SLP4-FTTH and SLP4-7 model combine the OPM4-4D optical power meter and either OLS7-FTTH (1310/1490/1550 nm) or OLS7-3 (1310/1550/1625 nm) LASER source respectively.
SLP4 Triple Wave Test Kits with Wave ID and Set Reference OLS7 Specifications Optical Wavelength (±20 nm) Emitter type Spectral width Output power Output stability Tone output General Model OLS7-FTTH Model OLS7-3 1310 nm 1490 nm 1550 nm 1310 nm 1550 nm 1625 nm Laser, Class I FDA 21 CFR 1040.10 and 1040.11, IEC 60825-1: 2007-03 5 nm 3 nm 5 nm 5 nm 5 nm 2 nm -5 dBm (typical) into 9/125 fiber ± 0.05 dB over 1 hour (after 15 min warm-up, after 30 sec typical) ± 0.
SLP4-6D Single-mode Test Kit with Wave ID and Set Reference The SLP4-6D test kit combines the OPM4-4D optical power meter and OLS2-Dual LASER light source and is ideally suited for testing single-mode fiber optic networks.
SLP4-6D Single-mode Test Kit with Wave ID and Set Reference OLS2-Dual specifications Optical OLS2-Dual (single port) Wavelength Emitter type 1310 ±20 nm 1550 ±20 nm Laser, Class I FDA 21 CFR 1040.10 and 1040.11, IEC 60825-1: 2007-03 Spectral width (FWHM) 5 nm (max) Output power 0 dBm* Output stability ± 0.05 dB over 1 hour (after 15 min. warm-up) ± 0.1 dB over 8 hours (after 15 min.
MLP5-2 Multimode Test Kit with Wave ID, Set Reference, and Data Storage The MLP5-2 test kit combines the OPM5-2D optical power meter and OLS1-Dual LED light source and is ideally suited for testing multimode fiber optic networks.
MLP5-2 Multimode Test Kit with Wave ID, Set Reference, and Data Storage OLS1-Dual specifications Optical OLS1-Dual (single port) Wavelength 850 ±30 nm Emitter type 1300 +50/-10 nm LED, Class I FDA 21 CFR 1040.10 and 1040.11, IEC 60825-1: 2007-03 Spectral width 40 nm (typ) 120 nm (typ) Output power >-20 dBm* Output stability ± 0.1 dB over 8 hours (after 5 min. warm-up) 62.
MLP4-2 Multimode Test Kit with Wave ID and Set Reference The MLP4-2 test kit combines the OPM4-2D optical power meter and OLS1-Dual LED light source and is ideally suited for testing multimode fiber optic networks.
MLP4-2 Multimode Test Kit with Wave ID and Set Reference OLS1-Dual specifications Optical OLS1-Dual (single port) Wavelength Emitter type 850 ±30 nm 1300 +50/-10 nm LED, Class I FDA 21 CFR 1040.10 and 1040.11, IEC 60825-1: 2007-03 Spectral width 40 nm (typ) 120 nm (typ) Output power >-20 dBm* Output stability ± 0.1 dB over 8 hours (after 5 min. warm-up) Fiber size 62.
MLP1 Fiber Optic Loss Test Kits The MLP1 test kits are inexpensive solutions for testing multimode and single-mode systems. By joining the OPM 1 optical power meter and the OLS1 optical light source, the MLP1 is a great kit for beginners or network owners. Two versions of the MLP1 test kit are available for testing Premises networks, LAN, and Gigabit Ethernet. The MLP1-1S test kit includes the OPM1-2C power meter and OLS1-1C light source.
CKSM-2 Contractor Series Multimode & Single-mode Test Kit with Set Reference Combining the CSM1-2 optical power meter, CSS1-MM Dual LED light source, and CSS1-SM Dual LASER source, the CKSM-2 is a cost-effective test kit designed for performing insertion loss measurements on multimode as well as single-mode fiber optic links. Weighing only 0.4 lb each, units are compact and convenient for field use.
CKSM-2 Contractor Series Multimode & Single-mode Test Kit with Set Reference CSS1-SM Specifications CSS1-MM Specifications Optical CSS1-SM (single port) Optical Output wavelength 1310 nm ±20 nm, 1550 nm ±20 nm Output wavelength 850 nm ±20 nm 1300 nm +40/-60 nm Spectral width (max) 5 nm Spectral width (max) 35 nm 170 nm Output power 0.0 dBm into 9/125 fiber CSS1-MM (single port) Output power Emitter type Laser, Class I FDA 21 CFR 1040.10 and 1040.
CKM-2 Contractor Series Multimode Test Kit with Set Reference Combining the CSM1-2 optical power meter and CSS1-MM Dual LED light source, the CMK-2 is a cost-effective test kit designed for performing insertion loss measurements on multimode fiber optic links. Weighing only 0.4 lb each, both units are compact and convenient for field use.
CKM-2 Contractor Series Multimode Test Kit with Set Reference CSS1-MM Specifications Optical CSS1-MM (single port) Output wavelength 850 nm ±20 nm 1300 nm +40/-60 nm Spectral width (max) 35 nm 170 nm Output power -20.0 dBm into 62.5/125 fiber Emitter type LED, Class I FDA 21 CFR 1040.10 and 1040.11, IEC 60825-1: 2007-03 Output stability ± 0.1 dB over 1 hour (after 30 sec typically) ± 0.
HiLite and VFI2 Visual Fault Identifiers The HiLite and VFI2 are compact and powerful visible red laser sources designed to troubleshoot faults on fiber optic cables. Light generated by these units will escape from sharp bends and breaks in jacketed or bare fibers, as well as poorly mated connectors. They enable technicians to quickly identify faults in fiber optic jumper cables, distribution frames, patch panels, and splice trays.
MT Tracer 12-Fiber Visible Laser Source & Display The MT Tracer is a compact multi-fiber visual fault identifier (red laser source) supporting 8 or 12 fiber MTP® connections. The user simply connects the 12-fiber cable directly to the unit. Fibers can be tested individually or all at once. By progressing sequentially through the fibers, cables can be quickly checked for polarity by verifying the proper order at the output.
OFI-FTTx Active ONT Detector The OFI-FTTx is a rugged, handheld optical fiber identifier designed to identify the presence or absence of an active Optical Network Terminal (ONT) on FTTx F2 fibers at the Fiber Distribution Hub (FDH). During a test the F2 fiber does not have to be removed from service. Thus the OFI-FTTx can verify whether a splitter pigtail at the FDH is connected to an active circuit before it is disconnected for fault location or re-use.
OFI Optical Fiber Identifiers Noyes Optical Fiber Identifiers are rugged, handheld, and easy-to-use fiber optic test instruments designed to detect optical signals transmitted through a single-mode fiber without disrupting traffic. During installation, maintenance, rerouting, or restoration; it is often necessary to isolate a specific fiber.
OFI Optical Fiber Identifiers Applications • Live fiber identification - used during installation, maintenance, rerouting, or restoration to positively identify fibers prior to cutting and splicing • Tone detection • The OFI 400 models may also be used for measuring core power or relative power Ordering Information Model Includes OFI 200D User's guide and carry case OFI 400 User's guide and carry case Specifications Detectable signal range Fiber Type Parameter 250 μm coated fiber (SMF-28 with 250 μm
DFS1 Digital FiberScope The DFS1 Digital FiberScope supports magnified video inspection of optical fiber connector end-faces during fiber optic cable and connector installation and maintenance. The ergonomically designed hand-held unit illuminates fiber end-faces and delivers magnified images via USB port to AFL’s M-series OTDRs (M200, M700) or C-series OTDRs and Certification Testers (C840, C850, C860, C880).
DFS1 Digital FiberScope Specifications DFS1 Digital FiberScope with M700 OTDR (All specifications valid at 25°C unless otherwise specified) MODEL DFS1 Magnification 400X Field of View ~400 µm x 300 µm Resolution 0.
DFS1 Digital FiberScope Ordering Information (continued) DFS1 Accessories DFS1-00-0001MR MODEL DFS1-04-0001MZ DESCRIPTION Soft carry case for DFS1 Digital FiberScope and adapters 1400-01-0093MZ 6-compartment adapter tip storage box 1400-01-0094MZ 11-compartment adapter tip storage box 8500-05-0001MZ One-Click Cleaner SC, ST, FC 8500-05-0002MZ One-Click Cleaner LC/MU DFS1 Adapter Tips The following table identifies commonly required adapter tips. Other adapter tips available.
DFS1 Digital FiberScope Ordering Information (continued) MODEL DESCRIPTION DFS1-00-0025MR Long extended tip for E2000/PC bulkhead adapter MU/PC BULKHEAD ADAPTER TIPS DFS1-00-0026MR Tip for MU/PC bulkhead adapter DFS1-00-0027MR Short extended tip for MU/PC bulkhead adapter DFS1-00-0028MR Medium extended tip for MU/PC bulkhead adapter DFS1-00-0029MR Long extended tip for MU/PC bulkhead adapter DFS1-00-0030MR 60° angled tip for MU/PC bulkhead adapter MTP/PC MULTI-FIBER ADAPTER TIPS (FERRULE & BULKHEAD) DFS1-00
OFS 300 Optical Fiber Scope The Noyes OFS 300 from AFL Telecommunications is a versatile Optical Fiber Scope with precision 200X magnification. This handheld and rugged scope is used for inspection of optical fiber connectors for scratches, dirt, or other problems normally associated with poor transmission performance. A built-in laser safety filter provides > 40 dB IR protection to reduce risk of injury to the eye if accidentally viewing an active fiber.
VS 300 View Safe Inspection Scope The VS 300 Video Fiber Scope removes concerns for eye safety while inspecting optical fiber connectors. The design eliminates the optical path to the eye by utilizing a miniature camera and a state-of-the-art micro-display that achieves unparalleled clarity and resolution. The VS 300 is modeled after the functionality of our highly successful OFS 300 product line with the following improvements: • The VS 300 has no optical path to the user’s eye.
VFS 2 Video Fiber Scope 2nd Generation The VFS 2 is a small versatile video fiber scope, which retains the superior image quality associated with Noyes inspection products. The unique “optical-knuckle” allows the user to orient the probe head in virtually any direction. This feature allows the user to view connectors that may be located in tight or difficult locations. With a probe head length of less than 8 cm (3.25”), access into crowded/cramped quarters becomes a reality.
VCP 1 USB Video Capture Port The VCP 1 Video Capture Port is an interfacing module that provides high-speed composite video signal to a digital format conversion for capturing and displaying video data on a PC. The VCP 1 simply attaches via a standard USB connector to you computer and offers “plug and play” installation.
FTS Series Fiber Optic Talk Sets Fiber Optic Talk Sets are an inexpensive solution to meet your communication needs when testing multimode or single-mode fiber optic cables. Designed for voice communication over spare fibers, they provide full duplex, hands-free operation. Ease of use and compact size allow the operators to focus on the task at hand, rather than operating the talk set.
SVA 1 Singlemode Variable Attenuator The SVA 1 Singlemode Variable Attenuator advances fiber optic field testing by offering superior performance in a low cost hand-held package. Utilizing a simplified, industry accepted attenuation technique, the innovative design of the SVA 1 offers superior resolution across the entire 60 dB dynamic range. Intended for field testing during installation, new equipment turn-ups, or routine maintenance, the SVA 1 is a complete, easy to use attenuator.
VOA5 Variable Fiber Optic Attenuator The Noyes VOA5 from AFL Telecommunications is a handheld variable optical attenuator suited for a wide range of fiber link certification and production test applications. Two models are available, the VOA5-MM multimode and the VOA5-SM single mode model. The VOA5 attenuator offers high bi-directional return loss and will maintain the set attenuation level when the unit is powered down.
Fusion Splicer Systems Catalogue
