VoiceFinder AP100 VoIP Gateway [Installation Guide] May 2006 Technical Sales Division AddPac Technology Co., Ltd. www.addpac.
VoiceFinder AP100 VoIP Gateway Installation Guide (Edition 1.0) [Table of Contents] Introduction CHAPTER 1 VoiceFinder AP100 Overview ..................................................... 9 1.1. Introduction to VoiceFinder AP100........................................................................................9 1.2. Main Features and Characteristics......................................................................................11 1.3. Hardware Configuration and Network Interfaces...........
VoiceFinder AP100 VoIP Gateway Installation Guide (Edition 1.0) [ List of Figures ] [Figure 1-1] Standard Configuration of Network Using VoiceFinder AP100 Gateway.............. 9 [Figure 1-2] Exterior of VoiceFinder AP100 VoIP Gateway ..................................................... 10 [Figure 1-3] Front Panel of VoiceFinder AP100 VoIP Gateway............................................... 15 [Figure 1-4] Rear Panel of VoiceFinder AP100 VoIP Gateway ...............................................
VoiceFinder AP100 VoIP Gateway Installation Guide (Edition 1.0) [ List of Tables ] [Table 1-1] Front Panel of VoiceFinder AP100 VoIP Gateway .................................................................... 16 [Table 1-2] Rear Panel of VoiceFinder AP100 VoIP Gateway..................................................................... 17 [Table 3-1] Package of VoiceFinder AP100.................................................................................................
VoiceFinder AP100 VoIP Gateway Installation Guide (Edition 1.0) Introduction This Introduction describes the organization of this document and the symbols and legend used in the document. [ Document Organization ] The purpose of this document is to help you install AP100 Gateway easily. This document consists of four chapters. If you have been used AP100 VoIP gateway before, refer to helpful chapters.
VoiceFinder AP100 VoIP Gateway Installation Guide (Edition 1.0) If you have any questions regarding AP100 or your product has any failures, please contact AddPac Technology Co., Ltd. AddPac Technology Co., Ltd. Fls. 2, 3, and 5, Jeong Am Bldg., 769-12, Yoksam-dong, Kangnam-ku, Seoul, Korea Phone: (02) 568-3848 (Rep.) Facsimile: (02) 568-3847 E-mail Address: info@addpac.com http://www.addpac.com The revision history of the VoiceFinder AP100 Installation Guide is as follows: Edition No.
VoiceFinder AP100 VoIP Gateway Installation Guide (Edition 1.0) [Symbols and Legends] The symbols and legends used in this document are as follows: z Commands and keywords are typed in Bold. z Variables that require user inputs are typed in Italic. z Square brackets ([]) are optional values. z Keywords that are required but need to be selected are grouped in braces ({}) and are separated by slashes (/). z Angle brackets (<>) are required parameters. They need to be replaced with numbers.
VoiceFinder AP100 VoIP Gateway Installation Guide (Edition 1.0) The following conventions are also used to draw the user’s attention: Category Description Danger Danger This symbol indicates possible danger. Misuse may result in physical injuries. Please follow the instructions to avoid any electric shocks. Warning Warning This symbol indicates that the users should be careful with the operation. Otherwise, it may result in hardware damage of the equipment or loss of data.
VoiceFinder AP100 VoIP Gateway Installation Guide (Edition 1.0) CHAPTER 1 VoiceFinder AP100 Overview 1.1. Introduction to VoiceFinder AP100 VoiceFinder AP100 VoIP Residential Gateway is a standard Voice over IP Gateway that allows you to use voice phones, facsimiles, or data communications by inter-connecting adjacent Local Area Network (LAN) or connecting LAN to Wide Area Network (WAN) or the broadband Internet such as ADSL and DOCSIS (Cable).
VoiceFinder AP100 VoIP Gateway Installation Guide (Edition 1.0) since it provides the same operation environment as the plain old AP VoIP gateway series to ensure very simple installation, operation, and maintenance, and can be used easily at home.
VoiceFinder AP100 VoIP Gateway Installation Guide (Edition 1.0) 1.2. Main Features and Characteristics VoiceFinder AP100 Voice Gateway is a small VoIP gateway solution available for small business environments (e.g. SOHO), cyber apartments, Internet games, and Internet users at home. This high quality VoIP product supports both routing and Internet-based voice calling to allow you to easily use VoIP phones at an affordable price.
VoiceFinder AP100 VoIP Gateway Installation Guide (Edition 1.0) Hardware Description (Hardware Specification) VoiceFinder AP100 VoIP gateway is based on state-of-the-art embedded hardware technologies, and supports various network interfaces and much system memory.
VoiceFinder AP100 VoIP Gateway Installation Guide (Edition 1.0) z Supports Transparent Bridging (IEEE Spanning Tree Protocol). Network Administration VoiceFinder AP100 VoIP Gateway supports the following network administration features for systematic management: z Supports standard SNMP Agent, MIB II, and Bridge MIB for systematic management. z Supports Telnet and Rlogin that enable remote control. z Performs management based on Web. z Ensures QoS through traffic queuing.
VoiceFinder AP100 VoIP Gateway Installation Guide (Edition 1.0) z Performs system diagnostics, which allow you to analyze network packets. z Performs automatic boot along with watchdog. z Performs data logging and management. z Performs IP statistics and accounting. Other Scalability Features VoiceFinder AP100 VoIP Gateway supports the following supplementary features: z Supports the DHCP server, relay, and client for easy IP management. z Supports NAT/PAT for efficient IP management.
VoiceFinder AP100 VoIP Gateway Installation Guide (Edition 1.0) 1.3. Hardware Configuration and Network Interfaces This section describes the exterior and network interfaces of VoiceFinder AP100 VoIP Gateway. 1.3.1. Names and Features of VoiceFinder AP100 Parts AP100 VoIP gateway is a compact network product made of high-strength ABS.
VoiceFinder AP100 VoIP Gateway Installation Guide (Edition 1.0) No. LED Description ① POWER Power LED. Displays whether the power is properly being supplied (Yellow). ② LAN0 Shows that LAN0 is being used (Green). ③ LAN1 Shows that LAN1 is being used (Green). ④ PHONE Shows that the phone is being used (Green). ⑤ LINE Shows that the line is being used (Red). ※ The LEDs on the front panel may vary depending on models.
VoiceFinder AP100 VoIP Gateway Installation Guide (Edition 1.0) Rear View of AP100 The rear panel of AP100 VoIP gateway has the 10/100Mbps Fast Ethernet interface port for WAN/LAN, and phone interfaces for voice processing, and allows you to configure a network for WAN-to-LAN routing services.
VoiceFinder AP100 VoIP Gateway Installation Guide (Edition 1.0) 1.3.2.
VoiceFinder AP100 VoIP Gateway Installation Guide (Edition 1.0) 1.3.3. Voice Processing Interfaces The FXS voice processing interfaces of AP100 VoIP Gateway can be connected to regular phones, facsimiles, and PBXs. z FXS Interface-Type Voice Processing Port z Optional PSTN Backup Port (AP100P Model) AP100 VoIP gateway is a network device that supports integrated services such as voice services and data services.
VoiceFinder AP100 VoIP Gateway Installation Guide (Edition 1.0) CHAPTER 2 Preparatory Installation Information on AP100 2.1. Recommendations for Installation Recommendations for the safe use of this product are as follows: • Install and use this product in a clear and dust-free place. • Open the cover in a flat and safe place. • Do not wear loose clothes that may be stuck by the product chassis during operation. If you wear a necktie or a scarf, be wary of its falling. Also, tuck up your sleeves.
VoiceFinder AP100 VoIP Gateway Installation Guide (Edition 1.0) place and an ungrounded power extension cable. ESD Prevention z 9 The main chipset of this product is very precise. If you handle its elements in a wrong method, the product may be damaged due to ESD. 9 Wear a wrist strap for ESD prevention, if any, and ground the cord before handling the product. 9 If you do not have a wrist strap, hold the metal part of the product chassis with one hand to prevent ESD. 2.1.2.
VoiceFinder AP100 VoIP Gateway Installation Guide (Edition 1.0) 2.2. Preparatory Information on Network Access Conform to the EMI standard and distance limitations in accordance with the EIA standard during installation. The following section describes the Ethernet cables and console cables supported by VoiceFinder AP100 as well as tools required for installation: 2.2.1.
VoiceFinder AP100 VoIP Gateway Installation Guide (Edition 1.0) CHAPTER 3 AP100 Installation 3.1. Unpacking and Verification Check if the package box that prevents physical damage is broken before unpacking the product. If you do not find damage, open the box and check if the following content is contained: No.
VoiceFinder AP100 VoIP Gateway Installation Guide (Edition 1.0) 3.2. Sequence of Connecting Cables to AP100 Interfaces z Install AP100 in an environment that conforms to the recommendations of Chapter 2. 3.2.1. Connecting Ethernet Interfaces z Connect the LAN0 interface to the LAN interface of the WAN device by using an RJ45 UTP cable. Connect the LAN1 interface to the internal LAN of the PC.
VoiceFinder AP100 VoIP Gateway Installation Guide (Edition 1.0) 3.2.2. Connecting Phone Interfaces z Connect voice devices for subscribers to the FXS port by using an RJ11 cable.
VoiceFinder AP100 VoIP Gateway Installation Guide (Edition 1.0) 3.2.3. Connecting PSTN Interfaces z Connect the external PSTN to the PSTN port by using a RJ11 cable.
VoiceFinder AP100 VoIP Gateway Installation Guide (Edition 1.0) 3.3. Power Supply and Verification of Proper Operation Before supplying the power, you should be aware of the following procedure for booting AP100: z AP100 performs a self-test, and checks if the CPU, memory, and interfaces are properly operating. z The boot loader operates, and finds an appropriate software image file. In the default configuration, the product loads the software in the flash memory.
VoiceFinder AP100 VoIP Gateway Installation Guide (Edition 1.0) After AP100 is installed and the interfaces are connected, the power should be supplied. The external power adapter should be connected to AP100 before power supply. Do not connect the adapter to AP100 after supplying the power to the adapter. If the power of 110V is supplied, you should use an external power adapter for 110V.
VoiceFinder AP100 VoIP Gateway Installation Guide (Edition 1.0) 3.3.1. Using AP100 Web Server Using Web Browser z To access from the user PC to AP100 Web Server, the IP address of 192.168.10.x should be set. (The IP address of AP100 Web Server is 192.168.10.1.) z The user PC should be connected to the LAN1 interface of AP100 one to one in order to access AP100 Web Server. z Run Internet Explorer, and then access AP100 Web Server. By default, the IP address of AP100 Web Server is 192.168.10.
VoiceFinder AP100 VoIP Gateway Installation Guide (Edition 1.
VoiceFinder AP100 VoIP Gateway Installation Guide (Edition 1.0) No. Option ① System ② Network ③ Speed Dial ④ VoIP Sets voip-peer. ⑤ SIP Sets the information on SIP register. ⑥ MGCP Sets the information on MGCP register. ⑦ H.323 Sets the information on H323 register. ⑧ Service Enables or disables FTP/HTTP/NTP. ⑨ ⑩ ⑪ Auto Description Allows you to check the current system information. Sets accounts. Sets WAN/LAN interfaces. Sets the speed dial. Sets up the auto-upgrade server.
VoiceFinder AP100 VoIP Gateway Installation Guide (Edition 1.0) 3.3.2. Connecting to Telnet Using HyperTerminal z If you want to connect to Telnet from the PC, a terminal emulator application should be installed. If you use a Microsoft Windows operating system, use the built-in HyperTerminal application. z Execute HyperTerminal, and name the connection in the New Connection dialog box randomly. For instance, name the connection AddPac.
VoiceFinder AP100 VoIP Gateway Installation Guide (Edition 1.0) z Set Connect Using: to TCP/IP (Winsock) from Connect to:. The IP address of the AP100 connected to the PC is, and the AP100 uses Port 23 by default.
VoiceFinder AP100 VoIP Gateway Installation Guide (Edition 1.0) z Once the login message is displayed, enter the login default, “root” and the password default, “router”. Then, the login will be complete. Once the login is complete, a prompt, “AP100>” will be displayed on the console terminal. [Figure 3-8] Example of Telnet Connection z The prompts displayed at AP100 Gateway are “AP100>” and “AP100#”.
VoiceFinder AP100 VoIP Gateway Installation Guide (Edition 1.0) CHAPTER 4 Appendix 4.1. Specification of VoiceFinder AP100 VoIP Gateway This Appendix describes the technical specifications of VoiceFinder AP100 VoIP Gateway. (* refers to ‘To be enabled’.) IP Routing Service IP Routing Protocols Static IEEE 802.1Q VLAN Routing LAN Service Ethernet Interface 10/100 Mbps Ethernet Interface Configures a port. Supports a secondary subnet. Configuration Management Changes the MTU size.
VoiceFinder AP100 VoIP Gateway Installation Guide (Edition 1.0) Voice over IP Service (Integrated Voice and Data Services) ITU-T H.323 v2 Protocol with ITU-T H.235 Security VoIP Protocols Feature Session Initiation Protocol (SIP) Media Gateway Control Protocol (MGCP) G.723.1 MP-MLQ, 6.3 Kbps, 5.3 Kbps Voice Compression G.729.A CS-ACELP, 8 Kbps G.711 PCM, 64 Kbps Voice Activity Detection (VAD) T.
VoiceFinder AP100 VoIP Gateway Installation Guide (Edition 1.
VoiceFinder AP100 VoIP Gateway Installation Guide (Edition 1.
VoiceFinder AP100 VoIP Gateway Installation Guide (Edition 1.0) 4.2. Cable Specification This section describes the pinout specification of the following cable used for AP100: z Pinout of Ethernet cable assembly (RJ-45 to RJ-45) [ Pinout of Ethernet Cable Assembly (RJ-45 to RJ-45) ] An RJ-45 to RJ-45 Ethernet cable is used to connect AP100 to another device (typically hub). The pin sequence of the RJ-45 connector is shown in Figure C-1.
VoiceFinder AP100 VoIP Gateway Installation Guide (Edition 1.0) AddPac Technology Co., Ltd. Floor Nos. 2/3/5, Jeong Am Bldg., 769-12, Yoksam-dong, Kangnam-ku, Seoul, Korea Phone: (02) 568-3848 (Rep.) Facsimile: (02) 568-3847 E-mail Address: info@addpac.com http://www.addpac.
