VoiceFinder AP200 VoIP Residential Gateway Installation Guide Release 1.0 June. 2003 AddPac Technology Co., Ltd. 2/ 3F, Jeong-Am Bldg, Kangnam-Gu, Seoul, Korea. Zip 135-080 Phone (82 2) 568-3848 Fax (82 2) 568-3847 E-mail: info@addpac.com http://www.addpac.
VoiceFinder AP200 VoIP Residential Gateway Installation Guide Version 1.0 AddPac Technology Co., Ltd.
VoiceFinder AP200 VoIP Residential Gateway Installation Guide Version 1.0 [Contents] About This Guide Chapter 1. VoiceFinder AP200 Overview ................................................................................................. 11 Introduction to VoiceFinder AP200 Gateway................................................................................... 11 Main Features ................................................................................................................................
VoiceFinder AP200 VoIP Residential Gateway Installation Guide Version 1.0 FXO Interface Connection ............................................................................................................32 VoiceFinder AP200 Interface connection example .......................................................................33 Booting................................................................................................................................................
VoiceFinder AP200 VoIP Residential Gateway Installation Guide Version 1.0 [Table of Figures] Figure 1-1: The network diagram using VoiceFinder AP200 Gateway ....................................................... 11 Figure 1-2: The exterior view of VoiceFinder AP200 Gateway ...................................................................12 Figure 1-3: VoiceFinder AP200 Gateway front view....................................................................................
VoiceFinder AP200 VoIP Residential Gateway Installation Guide Version 1.0 [Table of Tables] Table 1-1: The interfaces and explanation of the front panel of AP200 ......................................................18 Table 1-2: The interfaces and explanation of the rear panel of AP200 Gateway ........................................19 Table 1-3: Interfaces of VoiceFinder AP200 models ...................................................................................
VoiceFinder AP200 VoIP Residential Gateway Installation Guide Version 1.0 About This Guide This chapter outlines the structure of VoiceFinder AP200 VoIP Gateway Installation Guide and explains the symbols and legends. [Organization] The VoiceFinder AP200 VoIP Gateway Installation Guide is offered to assist the operation VoiceFinder AP200 VoIP Gateway. This manual is composed of 4 chapters. Experienced users may refer directly to the related chapters.
VoiceFinder AP200 VoIP Residential Gateway Installation Guide Version 1.0 For technical supports, please contact AddPac Technology Co. Ltd. AddPac Technology Co., Ltd 2/ 3 Fl. Jeong-Am Bulding, 769-12 YeoksamDong, Kangnam-Ku, Seoul, Korea Phone (02) 568-3848 Fax (02) 568-3847 E-mail: info@addpac.com http://www.addpac.com AddPac Technology Co., Ltd.
VoiceFinder AP200 VoIP Residential Gateway Installation Guide Version 1.0 The revision history of VoiceFinder AP200 VoIP Gateway Installation Guide is as follows. Revision No. Date Comments Version 1.0 June 2003 1 Edition AddPac Technology Co., Ltd.
VoiceFinder AP200 VoIP Residential Gateway Installation Guide Version 1.0 [Symbols and Legends] The symbols and legends used in this User’s Manual are as follows: z Commands and Keywords are typed in Bold. z Variables that require user inputs are typed in Italic. z Square brackets ([]) are optional values. z Keywords that are required but need to be selected are grouped in braces ({}) and are separated by Slashes (/). z Angle brackets (<>) are required parameters must be inputted.
VoiceFinder AP200 VoIP Residential Gateway Installation Guide Version 1.0 Chapter 1. VoiceFinder AP200 Overview Introduction to VoiceFinder AP200 Gateway Information VoiceFinder AP200 VoIP Residential Gateway (hereinafter “VoiceFinder AP200 Gateway”) is a VoIP gateway offering voice, fax and data service by connecting Local Area Networks, Wide Area Network or broadband network of ADSL and DOCSIS (Cable). The below is the network diagram using VoiceFinder AP200 Gateway.
VoiceFinder AP200 VoIP Residential Gateway Installation Guide Version 1.0 The below figure is the exterior view of VoiceFinder AP200 Gateway. Figure 1-2: The exterior view of VoiceFinder AP200 Gateway As a supplementary service, VoiceFinder AP200 Gateway provides Packet Filtering and Firewall function using an Access List method.
VoiceFinder AP200 VoIP Residential Gateway Installation Guide Version 1.0 Main Features Information VoiceFinder AP200 Gateway offers high speed Internet access function at enterprises, SOHO and ordinary households, also supports cutting-edge compression algorithm. It supports a LAN port for WAN connection, which can be connected to xDSL modem, maximum 2 FXS voice ports, LAN port for PC connection, and PTSN Backup (or FXO port) for PSTN connection.
VoiceFinder AP200 VoIP Residential Gateway Installation Guide Version 1.0 functions) z Compact, stylish design z AC-DC External Power Supply Adapter z Various System LEDs Voice over IP Service z VoiceFinder AP200 Gateway supports voice and data integration service, VoIP service. z Offers 1~2 channel Voice ports and offers VoIP service by interoperating with PBXs, ordinary telephones and fax machines. z Supports industry standard VoIP protocols such as H.323, SIP and MGCP.
VoiceFinder AP200 VoIP Residential Gateway Installation Guide Version 1.0 Network Managements VoiceFinder AP200 Gateway supports various network management protocols and functions. z Standard SNMP Agent (MIB v2), MIB II, Bridge MIB Support z Consol function with Async. Port. z Remote Management using Console, Rlogin, Telnet. z Traffic Queuing z Web based Managements Security Functions VoiceFinder AP200 Gateway supports various security functions.
VoiceFinder AP200 VoIP Residential Gateway Installation Guide Version 1.0 Operation and Managements VoiceFinder AP200 Gateway supports following operation and maintenance features.
VoiceFinder AP200 VoIP Residential Gateway Installation Guide Version 1.0 Hardware Configuration and Network Interface Information This Chapter explains the external form and network interfaces of VoiceFinder AP200 Gateway. VoiceFinder AP200 Gateway Part & Description VoiceFinder AP200 Gateway is made by the high intensity ABS with compact design. The front panel of VoiceFinder AP200 Gateway includes various LEDs indicating the operational status of the device.
VoiceFinder AP200 VoIP Residential Gateway Installation Guide Version 1.0 Table 1-1 shows the functional explanation about each LED of VoiceFinder AP200 Gateway. Table 1-1: The interfaces and explanation of the front panel of AP200 No. Interface Explanation (1) POWER (2) FXS0 Display the operation status of “FXS0” voice interface port. (Orange) (3) FXS1 Display the operation status of “FXS1” voice interface port.
VoiceFinder AP200 VoIP Residential Gateway Installation Guide Version 1.0 Rear View of AP200 The rear side of the VoiceFinder AP200 VoIP Gateway includes 10Mbps Ethernet Interface for WAN/LAN interface, PSTN port, RS-232C serial port for management, and FXS/ FXO interface port for voice signal processing. It can also form network environment for WAN-to-LAN routing service. Standard Configuration Model Following figure shows the standard configuration of the back panel of VoiceFinder AP200 gateway.
VoiceFinder AP200 VoIP Residential Gateway Installation Guide Version 1.0 Following figures show the back panel interface pictures of VoiceFinder AP200 Gateway. Figure 1-5: The real panel of VoiceFinder AP200B model Figure 1-6: The real panel of VoiceFinder AP200C model Figure 1-7: The rear panel of VoiceFinder AP200D model Figure 1-8: The rear panel of VoiceFinder AP200E model AddPac Technology Co., Ltd.
VoiceFinder AP200 VoIP Residential Gateway Installation Guide Version 1.0 Table 1-3: Interfaces of VoiceFinder AP200 models Model Ethernet FXS FXO PSTN Console AP200-B 2 x 10Mbps 2 None 1 1 AP200-C 2 x 10Mbps 1 None 1 1 AP200-D 2 x 10Mbps None 2 None 1 AP200-E 2 x 10Mbps 1 1 None 1 AddPac Technology Co., Ltd.
VoiceFinder AP200 VoIP Residential Gateway Installation Guide Version 1.0 Network Interface VoiceFinder AP200 Gateway supports the following network interfaces: z 1 Port 10Mbps Ethernet Interface for WAN z 1 Port 10Mbps Ethernet Interface for LAN z 1 Port RS232C Asynchronous Serial Interface With the above network interface, VoiceFinder AP200 Gateway can establish WAN and LAN network supporting TCP/IP network protocol.
VoiceFinder AP200 VoIP Residential Gateway Installation Guide Version 1.0 Voice Processing Interfaces The fixed voice interface of VoiceFinder AP200 Gateway can be connected to the ordinary telephones, fax machines and PBX. z FXS Interface voice processing port z FXO Interface voice processing port z PSTN Backup port for PSTN connection VoiceFinder AP200 Gateway is a network device offers not only data service, but also voice service at one device.
VoiceFinder AP200 VoIP Residential Gateway Installation Guide Version 1.0 Chapter 2. Before Installation Installation Requirements Warning The following recommendation should be followed for safe operation of the product. z Ensure VoiceFinder AP200 Gateway is in a dust-free environment before and after installation. z Make sure to open VoiceFinder AP200 Gateway cover on a flat and safe surface.
VoiceFinder AP200 VoIP Residential Gateway Installation Guide Version 1.0 z Prevention of Static Electricity 9 The main chip-set of the Gateway is very delicate and misuse may result in static electrical damage. 9 If a static prevention wrist strap is available, strap it around the wrist and earth the cord before operating the equipment. 9 If no wrist strap is available, earthening by holding a metal part of the Chassis will help prevent static electricity.
VoiceFinder AP200 VoIP Residential Gateway Installation Guide Version 1.0 Network Connection Requirements Consider EMI Standard and distance limitation while installing VoiceFinder AP200 Warning Gateway. The below explains PSTN cable, Ethernet cable, Console Cable of VoiceFinder AP200 Gateway. Necessaries Unless ordered in advance, the tools and certain cables are not provided in the package. Prepare the following equipments and tools before the installation.
VoiceFinder AP200 VoIP Residential Gateway Installation Guide Version 1.0 Ethernet Port VoiceFinder AP200 Gateway offers two (2) RJ45 type 10BaseTX Ethernet Ports on the rear panel and LEDs are indicating the port status are on the front panel. The PIN information of the Ethernet cable, refer to Chapter 4. RS-232C Serial Console Port VoiceFinder AP200 Gateway offers one (1) RJ-45 type RS-232C connector on the rear panel. This port is for the initial configuration, monitoring and debugging.
VoiceFinder AP200 VoIP Residential Gateway Installation Guide Version 1.0 Chapter 3. Gateway Installation Unpacking Before unpacking, check for external damage to the packaging box. If no external damages are found, confirm if the following items are enclosed. Table 3-1: VoiceFinder AP200 Gateway package No.
VoiceFinder AP200 VoIP Residential Gateway Installation Guide Version 1.0 VoiceFinder AP200 Interfaces and Cable connection z Install VoiceFinder AP200 Gateway at the suitable place illustrated at Chapter 2. Async Serial Interface Connection z Connect RJ45 connector of RS-232C serial console cable to the Console port and connect the other side of the cable at the serial port of the PC. Console Cable PC Figure 3-1: Connect VoiceFinder AP200 Gateway and Console PC AddPac Technology Co., Ltd.
VoiceFinder AP200 VoIP Residential Gateway Installation Guide Version 1.0 Ethernet Interface Connection z With RJ45 UTP cable, connect LAN0 port of VoiceFinder AP200 Gateway and LAN interface of the WAN equipment. Also, connect LAN1 interface of the gateway with LAN interface of the user PC. Ethernet Cable (RJ45) WAN (IP Network) PC Figure 3-2: Connect VoiceFinder AP200 Gateway with WAN and normal PC AddPac Technology Co., Ltd.
VoiceFinder AP200 VoIP Residential Gateway Installation Guide Version 1.0 FXS Voice Interface Connection z Connect FXS port to an analog phone with RJ11 cable. Figure 3-3: Connect VoiceFinder AP200 Gateway and a normal telephone PSTN Interface Connection z Connect the PSTN line to the PSTN port with RJ11 cable. RJ11 to RJ11 Phone Cable PSTN Figure 3-4: Connect VoiceFinder AP200 Gateway and a PSTN line AddPac Technology Co., Ltd.
VoiceFinder AP200 VoIP Residential Gateway Installation Guide Version 1.0 FXO Interface Connection z Connect FXO Interfaces to PBX (Private Branch eXchange) with RJ11 cable. z Applicable to the models supporting FXO Interface. Figure 3-5: Connect VoiceFinder AP200 Gateway and PBX AddPac Technology Co., Ltd.
VoiceFinder AP200 VoIP Residential Gateway Installation Guide Version 1.0 VoiceFinder AP200 Interface connection example The below figure is the interface connection example of VoiceFinder AP200 Gateway. PSTN PC PC Analog Phone WAN (IP Network) Figure 3-6: The example of interface connection AddPac Technology Co., Ltd.
VoiceFinder AP200 VoIP Residential Gateway Installation Guide Version 1.0 Booting When power is supplied, the system is booted as described below z VoiceFinder AP200 Gateway performs a self-test and checks basic operations of the CPU, the memory and interfaces. z The boot loader is executed, and the boot loader seeks for proper software image files. z The boot loader loads APOS software from the flash memory.
VoiceFinder AP200 VoIP Residential Gateway Installation Guide Version 1.0 Danger After connecting all the interfaces, supply the power to VoiceFinder AP200 Gateway. Turn on the power after connecting the power adapter to VoiceFinder AP200 Gateway. not connect the adapter to the power supply before connecting it to the gateway. use 110V adapter in case the power supply is 110V. Do Also, However, free voltage power adapter detects both 110V and 220V, so there is no additional setting required.
VoiceFinder AP200 VoIP Residential Gateway Installation Guide Version 1.0 Use Console terminal with HyperTerminal z To use a PC as a Console terminal, the communication emulator application should be installed. When the PC is MS-Windows line, use the HyperTerminal Application. Figure 3-7: MS-Windows Communication Emulator HyperTerminal AddPac Technology Co., Ltd.
VoiceFinder AP200 VoIP Residential Gateway Installation Guide Version 1.0 Assign a name to the connection. “AddPac” is used at the below example. Figure 3-8: Assign a name for the new connection AddPac Technology Co., Ltd.
VoiceFinder AP200 VoIP Residential Gateway Installation Guide Version 1.0 z Select the interface whether the Console cable is connected. Typically, the Console cable is connected to the RS-232C 9Pin Serial Port, so select the right port according to the user environment. “COM1” is selected at the below example. Figure 3-9: Select the interface for Console cable AddPac Technology Co., Ltd.
VoiceFinder AP200 VoIP Residential Gateway Installation Guide Version 1.0 z Set the port information. The below examples is based on “COM1” port. Figure 3-10: COM1 Properties AddPac Technology Co., Ltd.
VoiceFinder AP200 VoIP Residential Gateway Installation Guide Version 1.0 z After the configuration, press “Enter” button, then the below message will be displayed on the HyperTerminal. This message shows the routing S/W version, Gateway H/W test result, memory and etc. System Boot Loader, Version 1.3.6/1 Copyright (c) by AddPac Technology Co., Ltd. Since 1999.
VoiceFinder AP200 VoIP Residential Gateway Installation Guide Version 1.0 The System is ready. Please login to system. login: Interface ethernet0.0, changed state to UP login: root password:****** RGW - Login : root at Console on Thu Jan 1 03:14:59 1970 router# Figure 3-11: The HyperTerminal message of VoiceFinder AP200 Gateway z With the log-in message, input the user name “root” and the password “router”. After the log-in process, the prompt “router#” is displayed on the console terminal.
VoiceFinder AP200 VoIP Residential Gateway Installation Guide Version 1.0 Chapter 4. Appendix VoiceFinder AP200 Gateway Technical Description This Chapter explains the supported Technical Specification of VoiceFinder AP200 VoIP Gateway. (* means that the item is not yet implemented.) IP Routing Service IP Routing Protocols Static IEEE 802.
VoiceFinder AP200 VoIP Residential Gateway Installation Guide Version 1.
VoiceFinder AP200 VoIP Residential Gateway Installation Guide Version 1.
VoiceFinder AP200 VoIP Residential Gateway Installation Guide Version 1.0 Cable Specification This Appendix provides information about the Pinout specifications of the following cables used with VoiceFinder AP200 Gateway. z Console Port Signal and Pinout (RJ-45 to DB9) z Ethernet Cable Assemble (RJ-45 to RJ-45) Pinout [Console Port Signal & Pinout] In order to connect the gateway console port with the Terminal Emulating PC, the RJ45 to DB9 (Female DTE Connector) cable is used.
VoiceFinder AP200 VoIP Residential Gateway Installation Guide Version 1.0 [Ethernet Cable Assemble (RJ-45 to RJ-45) Pinout] In order to connect the gateway with other equipments (i.e. HUB), the RJ-45 to RJ-45 Ethernet Cable is used. The RJ-45 Connector Pin sequence is provided below and the transferred signal and Pinout specifications are enlisted at the below table.