AP-IP120 IP Phone [Installation and Operation Guide] March, 2009 AddPac Technology Co., Ltd. www.addpac.
AP-IP120 IP Phone Installation Guide Version 1.0 AP-IP120 IP Phone Note. The specifications and information in this guide are subject to change without notice. All statements, information, and recommendations in this guide are believed to be accurate but are presented without warranty of any kind, express or implied.
AP-IP120 IP Phone Installation Guide Version 1.
AP-IP120 IP Phone Installation Guide Version 1.0 [Contents] Getting into AP-IP120 IP Phone Installation Guide ..................................................................... 13 Chapter 1. Product Overview ............................................................................ 15 Product Overview ........................................................................................................................... 15 Hardware Features ......................................................
AP-IP120 IP Phone Installation Guide Version 1.0 Tool Box – Ring Setup ................................................................................................................... 62 Tool Box – Auto Upgrade ...............................................................................................................66 ToolBox-User Loc ……………………….………………………………………………………………69 Tool Box-Version Info…………………………………………………………………………………….74 Network Setup Menu Category .............................................
AP-IP120 IP Phone Installation Guide Version 1.0 System Setup – Voice Class Codec ........................................................................................... 138 System Setup – Auto Answer ..................................................................................................... 141 System Setup – Hook…………………………………………………………………………………...144 System Setup – Emergency ........................................................................................................ 146 Chapter 5.
AP-IP120 IP Phone Installation Guide Version 1.0 [Figures] (Figure 1-1) Network Configuration Diagram ........................................................................ 17 (Figure 1-2) Front View ......................................................................................................... 21 (Figure 1-3) Rear View .......................................................................................................... 23 (Figure 3-1) Connecting WAN .......................................
AP-IP120 IP Phone Installation Guide Version 1.0 (Figure 4-25) IPv4 Setup Menu Section ................................................................................ 77 (Figure 4-26) IPv4 DHCP Setting Menu Detail ...................................................................... 79 (Figure 4-27) Static IP Menu Detail ....................................................................................... 80 (Figure 4-28) PPPoE Setting Menu Detail.........................................................
AP-IP120 IP Phone Installation Guide Version 1.0 (Figure 6-1) Terminal Emulator HyperTerminal on MS-Windows ........................................ 153 (Figure 6-2) Name Entry for HyperTerminal Connection ..................................................... 154 (Figure 6-3) Access to Telnet by Using TCP/IP ................................................................... 155 (Figure 6-4) Login Screen ...................................................................................................
AP-IP120 IP Phone Installation Guide Version 1.0 [Table] [Table 1-1] Hardware Specifications ...................................................................................... 18 [Table 1-2] Software Specifications ....................................................................................... 19 [Table 1-3] Description of the Button Features ...................................................................... 22 [Table 1-4] Description of the Interfaces on the Rear Side .....................
AP-IP120 IP Phone Installation Guide Version 1.0 [Table 4-18] Description of PPPoE Setting Menu Detail........................................................ 83 [Table 4-19] Description of LAN Setup Menu Section ........................................................... 85 [Table 4-20] Description of SIP Protocol Menu Detail ........................................................... 90 [Table 4-21] Description of QoS Menu Option .......................................................................
AP-IP120 IP Phone Installation Guide Version 1.0 [Table 9-1] The signal and Pinout specification ................................................................... 170 [Table 8-1] Console Port Pinout .......................................................................................... 170 [Table 8-2] Signal and Pinout of Direct Ethernet Cable .......................................................
AP-IP120 IP Phone Installation Guide Version 1.0 Getting into AP-IP120 IP Phone Installation Guide This chapter explains the AP-IP120 IP Phone installation guide. [ Contents of AP-IP120 Installation Guide] The purpose of this guide is to assist the users to install the AP-IP120 IP Phone easily. This guide is composed of five chapters as to follow. If you have a previous experience of using IP Phone, please refer to the chapters the user wants to know directly.
AP-IP120 IP Phone Installation Guide Version 1.0 If you have any questions and need any technical support of AP-IP300, please contact AddPac Technology in the followings: AddPac Technology Co., Ltd. 2nd Fl. Jeong-Am Building, 769-12 Yeoksam-Dong, Kangnam-Ku, Seoul , Korea Phone (02) 568-3848 Fax (02) 568-3847 E-mail : info@addpac.com http://www.addpac.com The revision history of AP-IP120 IP Phone installation guide is listed as to follow: Revision History Revision No. Version 1.
AP-IP120 IP Phone Installation Guide Version 1.0 Chapter 1. Product Overview AP-IP120 IP phone is designed to provide enhanced IP telephony functionality to meet the wide range of business user requirements. This cost effective IP phone optimally delivers rich featured voice telephony service on ordinary internet infrastructure as well as AddPac IP-PBX environment on local LAN as a fully featured IP extension for the complete AddPac VoIP solution.
AP-IP120 IP Phone Installation Guide Version 1.0 Buttons. Adapt to the Future Environment : Firmware Upgradeable Technology Designed on programmable high performance RISC Integrated DSP Technology, AP-IP120 is capable of adopting new capabilities and improvement by downloading firmware from website or with its autoupgrade option as the customers' needs grow.
AP-IP120 IP Phone Installation Guide Version 1.
AP-IP120 IP Phone Installation Guide Version 1.0 Hardware Features [Table 1-1] Hardware Specifications Category Specification Model Product Category Microprocessor Digit and Key Buttopns AP-IP120 IP Phone (Built-in Speaker Phone) High Performance RISC CPU Architecture 3 x 4 Standard Numeric Buttons, 17 Menu/ Function Key Speed Dialing Keys, 12 SpeedDial and Presence Indication Keys 4 Line Graphic LCD 512Kbyte Flash Memory 4MB Flash Memory 16MB High Speed SDRAM One(1)-3.
AP-IP120 IP Phone Installation Guide Version 1.0 Software Features [Table 1-2] Software Specifications Category Specification LAN Protocol Static IPv4 Routing WAN Protocol Point-to-Point Protocol (PPPoE for ADSL), etc. Audio Service Voice Codec & - G.711, G.723.1, G.726, G.729, etc. Signaling Protocol SIP, and MGCP Triple Stack Support ITU-T H.235 Security Feature Voice Processing Features Supports - VAD, DTMF, CNG, G.168 and T.
AP-IP120 IP Phone Installation Guide Version 1.
AP-IP120 IP Phone Installation Guide Version 1.0 Physical Description-Front View This chapter explains the front part’s DIAL and FUNCTION KEY of AP-IP300 IP Phone. The external case is made of high degree of solidity ABS. Main key buttons are equipped on front part so that user can operate all the functions with these buttons.
AP-IP120 IP Phone Installation Guide Version 1.0 The following Table 1-3explains each button feature of AP-IP300 on the front side. [Table 1-3] Description of the Button Features No. Button Names Features (1) Menu Enter the UI Main Menu (2) F1~F4 The soft keys which are displayed on the bottom of LCD screen and can be assigned with each different function such as Phonebook and Speed-Dial.
AP-IP120 IP Phone Installation Guide Version 1.0 Physical Description-Rear View The rear side is composed of FXO PSTN backup interface, USB interface, power switch and connector and two (2) Fast Ethernet for WAN/LAN connections. (Figure 1-3) Rear View [Table 1-4] explains the interfaces on the rear side. [Table 1-4] Description of the Interfaces on the Rear Side No. Interface Description (1) DC 5V 2A External Power Adaptor connector (DC 5V 2A).
AP-IP120 IP Phone Installation Guide Version 1.0 Chapter 2. Preparing for Installation Installation Requirement The followings are the recommendation for safe operation of the equipment. • Ensure AP-IP120 IP Phone is in a dust-free environment before and after installation. • Ensure AP-IP120 IP Phone upper part is empty on a flat and safe surface. • To prevent accidents, avoid ties, scarf, sleeves, and any other loose clothing from entangling with the chassis.
AP-IP120 IP Phone Installation Guide Version 1.0 Site Requirements The AP-IP120 is ready for use where electronic products are used. However, a location with the following conditions is recommended for the maximum performance: • A level and well ventilated location is recommended. • Secure the equipment safely where intended to install. • Avoid placing objects on top of the equipment. • • Install the equipment in a cool location avoiding direct sunlight.
AP-IP120 IP Phone Installation Guide Version 1.0 Requirements for Network Connection This procedure is to follow EIA standards and other EMI regulations when you install the Gateway The following section describes the Ethernet Cable, and the Console Cable which can be connected to the AP-IP120. Required Tools and Equipment Some cables and equipment are not included and your need to purchase them separately.
AP-IP120 IP Phone Installation Guide Version 1.
AP-IP120 IP Phone Installation Guide Version 1.0 Chapter 3. Installing Connecting Ethernet • A connection to Internet is made through the LAN interface of the WAN accessing equipment such as router, ADSL or cable modem. The LAN is connected by RJ45 standard of the UTP cable.
AP-IP120 IP Phone Installation Guide Version 1.0 • When LAN1 is set to IP-Share mode, it is connected to PC on Direct-Through cable.
AP-IP120 IP Phone Installation Guide Version 1.0 Connecting PSTN Line (FXO-Optional) This PSTN port is used for connecting PSTN Central Office line in case of a network failure. The user may connect the PSTN cable to the PSTN port in order to implement PSTN backup. As shown in the figure below, connect the PSTN cable. ( available in AP-IP120E).
AP-IP120 IP Phone Installation Guide Version 1.0 Connecting Analog Phone Line (FXS) This PSTN port is used for connecting PSTN Central Office line in case of a network failure. The user may connect the PSTN cable to the PSTN port in order to implement PSTN backup. As shown in the figure below, connect the PSTN cable.
AP-IP120 IP Phone Installation Guide Version 1.0 Connecting Audio-In/Out Interface Audio-In/Out port located at left side of AP-IP120 IP Phone is for audio devices such as MIC, Speaker System or Headset Device etc. Connect this port to MIC system or External Speaker System using ‘3.5mm stereo jack’ cable. .
Using the Dial Pad Buttons You can enter the characters by using the dial pad buttons in the Menu options: (Figure 3-6) Dial Pad Buttons Layout [Table 3-1] The Characters Associated with the Dial Pad Buttons Dial Pad Characters Description Buttons 1 1 < > & ( ) The characters can be changed in the order as you press the same button consistently.
AP-IP120 IP Phone Installation Guide Version 1.0 may wait 2 seconds to enter the second character after entering the first one.
AP-IP120 IP Phone Installation Guide Version 1.0 (Figure 3-8) Cancel Button on the Keypad [Table 3-3] Using Cancel Button on the Keypad Functions Description hang off The END button works as to hang off the phone while you are in conversation drop call When you make a call by pressing the Call button, you can use the END button to drop the call.
AP-IP120 IP Phone Installation Guide Version 1.0 Using the Soft-key Interworking with SSCP Softkey functions are supported by SSCP and change depending on the status of the phone (for example, when you are on a call or the phone is not in use) which are shown at the bottom of the LCD screen and they are interconnected with the 4 buttons of the softkey. When more than 4 softkeys present, you can see more softkeys by pressing F4 (‘More’) in the next screen.
AP-IP120 IP Phone Installation Guide Version 1.0 group 4 EndC (End Call) Allows you to pick up incoming calls within their own group [Table 3-6] Available Softkey Features in Busy State No Function Description 1 Hold Places a call on hold 2 EndC (End Call) Ends a call 3 Tran(Transfer) Transfers a call to the other extension 4 Park Allows you to place an incoming call on hold by pressing Park button, then you can see the Park number on the LCD screen.
AP-IP120 IP Phone Installation Guide Version 1.
AP-IP120 IP Phone Installation Guide Version 1.
AP-IP120 IP Phone Installation Guide Version 1.0 Chapter 4. Using AP-IP120 Default Screen Once the start-up operation is completed, the default screen is organized as it is shown in (Figure 4-1). (Figure 4-1) Default Screen [Table 4-1] Description of Default Screen No. Description Date and Time ① Display the present date & time.
AP-IP120 IP Phone Installation Guide Version 1.0 Phone Book Menu Category The Phone Book is a directory in which user can search by name and number and has the functions including phone number registration, recent call history, group lookup, button list, the default setting. It also has call log and speed dial menu.
AP-IP120 IP Phone Installation Guide Version 1.0 Phonebook – Search The Phonebook uses the registered name, phone number and speed dial number to search the phone number.
AP-IP120 IP Phone Installation Guide Version 1.0 [Table 4-2] Description of Search Menu Section Category Description Search by the name which has been saved in the Phone Book previously. If the Name has more than 2 fields that are same as the search word, all of them are displayed.
AP-IP120 IP Phone Installation Guide Version 1.0 Phone Book – Registration This option allows you to register a new telephone number to the Phone Book. You can use this registered number for other option of search and speed dial.
AP-IP120 IP Phone Installation Guide Version 1.0 [Table 4-3] Description of Register Menu Section Registration Parameters Description Enter the index number for the speed dial. Register a name of the other party to Phone Book Enter the other party’s group in Phone Book. Enter the other party’s number in Phone Book. Enter the other party’s IP address in Phone Book. * You must press OK button to apply all the settings after completing registration.
AP-IP120 IP Phone Installation Guide Version 1.0 Phonebook – Speed Dial The telephone numbers are listed per LCD display by simply using name. User can quickly find and make a call to others on the list in this menu. You can also press Call button by using a saved phone number.
AP-IP120 IP Phone Installation Guide Version 1.
AP-IP120 IP Phone Installation Guide Version 1.0 Phonebook – Group You can use Group Menu Section to store, manage and use the phone number by group. You can differentiate the bell sound for each group.
AP-IP120 IP Phone Installation Guide Version 1.0 [Table 4-5] Description of Group Menu Section Option Description Select a group number to be used in Phone Book. Enter a group name in Phone Book. Make a selection of bell sound for each group. * You must press OK button to apply all the settings after completing registration. If you want keep the settings after restart, the settings must be saved to Tool Box-Save (reference to Tool Box Menu).
AP-IP120 IP Phone Installation Guide Version 1.0 Phonebook – Button List Button List Menu Section specifies Speed Button List. The list takes the speed dial list which is configured to the server by using Button Profile Menu Section from the presence server.
AP-IP120 IP Phone Installation Guide Version 1.0 [Table 4-6] Description of Button List Menu Section Category Description Name Set a name for the Speed Button.
AP-IP120 IP Phone Installation Guide Version 1.0 Phonebook – Button Profile The Button Profile can interoperate with the Presence Server only. The user can choose the Button Profile form the Speed Button List which has been provided from the server.
AP-IP120 IP Phone Installation Guide Version 1.
AP-IP120 IP Phone Installation Guide Version 1.0 Phonebook – Recent Call The recent call displays a call log of the user for incoming and outgoing calls. This feature enables the user to check any incoming call which has been arrived during one’s absence, calls back by using the number of the incoming call and save the number of the incoming calls. 2 different ways of (Figure 4-10) and (Figure 4-11) are used to retrieving Recent Call.
AP-IP120 IP Phone Installation Guide Version 1.0 (Figure 4-11) Recent Call Menu Section 2 [Table 4-8] Description of Call Menu Option 2 Option Description 01.
Tool Box Menu Category Tool Box menu consists of date/time setting, configuration saving, initialization to factory default mode and language selection.
AP-IP120 IP Phone Installation Guide Version 1.0 Tool Box – Date & Time The user can set the date and time.
AP-IP120 IP Phone Installation Guide Version 1.
AP-IP120 IP Phone Installation Guide Version 1.0 Tool Box – Language You can select a language of your choice. You can choose English or Korean.
AP-IP120 IP Phone Installation Guide Version 1.0 Tool Box – Factory Default The Factory Default deletes all the configured settings of AP-IP120 and all the content on phone book and recent call menu. This command reboots the system automatically. This command is not recommended to use except for some inevitable circumstances.
AP-IP120 IP Phone Installation Guide Version 1.0 Tool Box – Save All This UI menu saves the settings which the user has entered in UI. Once the settings are saved, values are preserved even after rebooting.
AP-IP120 IP Phone Installation Guide Version 1.0 Tool Box – Ring Setup You can set the ringer up to 8 different kinds of sound including mute on the integrated speaker, in the ringer settings. The user can choose the sound that one likes after hearing the 7 different kinds of sound, except the mute, by using F1(Play). Also the volume can be adjusted.
AP-IP120 IP Phone Installation Guide Version 1.
AP-IP120 IP Phone Installation Guide Version 1.
AP-IP120 IP Phone Installation Guide Version 1.
AP-IP120 IP Phone Installation Guide Version 1.0 Tool Box – Auto Upgrade Whenever a new feature is added, the software (firmware) of the IP phone needs to be upgraded. One of the ways of doing this upgrade is download the new software by using a network transmission protocol such as ftp which is capable of transmitting a large files. This Auto Upgrade enables the phone to access a particular server and to compare the version of OS and Configuration. Then it determines to download the firmware. .
AP-IP120 IP Phone Installation Guide Version 1.0 (Figure 4-19) Auto Upgrade Menu Section [Table 4-12] Description of Auto Upgrade Menu Option Menu Sections Description Enter URL of the Auto Upgrade server Ex)down.addpac.com/apos/IP120/packing.
AP-IP120 IP Phone Installation Guide Version 1.0 Enter the password for an authorized access to the Auto Upgrade server Ex) addpac The succeeded Auto Upgrade can be kept in a record for a certain time. The basic default value is set to 30 days. The failed Auto Upgrade can be kept in a record for a certain time. The basic default value is set to 10 minutes. Enter a Port of the Auto Upgrade Server. The default value is set to 80 for HTTP.
AP-IP120 IP Phone Installation Guide Version 1.0 Tool Box - User Lock User Lock menu component configures the settings to block the entry to a particular menu section and changes the password. ‘0000’ is set at the default. Keeping the same password is recommended.
AP-IP120 IP Phone Installation Guide Version 1.0 [Table 4-13] Description of User Lock Menu Option Option Description Enable/Disable(Default : Enable) Replaces the old password with the new one (Default : 0000) Selects the menu section to be locked by password. The available menu sections are Incoming Lock, Outgoing Lock, and Menu Lock.
AP-IP120 IP Phone Installation Guide Version 1.0 Tool Box - Admin Lock Admin Lock menu component configures the settings to block the entry to a particular menu and changes the password. ‘2337’ is set at the default. Keeping the same password is recommended.
AP-IP120 IP Phone Installation Guide Version 1.
AP-IP120 IP Phone Installation Guide Version 1.
AP-IP120 IP Phone Installation Guide Version 1.0 Tool Box-Version Info This option allows you to verify the version of the software running at this present time.
AP-IP120 IP Phone Installation Guide Version 1.0 [Table 4-15] Description of Version Info Menu Option Menu Detail Description This is the version running at this present time This is the name of the firmware running at this present time.
AP-IP120 IP Phone Installation Guide Version 1.0 Network Setup Menu Category The network setup of AP-IP120 is organized in details of WAN, LAN interface setting, SIP/H.323 signaling, FTP service, QoS for guaranteeing VoIP quality, call options and others. This menu option is very important and the user must be familiar with them for using AP-IP120.
AP-IP120 IP Phone Installation Guide Version 1.0 Network Setup – Internet This internet menu has the optional features for the WAN interface. Since there are many different network settings, the user has to choose the features which are most suitable to the given. These WAN protocols supported by AP-IP120 are DHCP, static IPv4, PPPoE, and IPv6 etc.
AP-IP120 IP Phone Installation Guide Version 1.0 [Table 4-16] Description of IPv4 Setting Menu Option Menu Detail Description Enable/ Disable IPv4 Enable DHCP server to take a dynamic IP address fromWAN protocol such as cable , VDSL, ADSL modems Set IP address manually and build WAN interface such as static IP ADSL, E1/T1 leased line. Getting a dynamic IP address from PPP server such as ADSL.
IPv4 Setting– DHCP If user enables DHCP protocol in network setup internet menu, user gets a dynamic IP address from DHCP server such as cable modem, VDSL, IP-ADSL.
IPv4 Setting – Static IP If you want to use static IP address, you may find this menu helpful to set a static IPv4 address manually and to configure WAN interface such as static IP ADSL, E1/T1 leased line, etc..
AP-IP120 IP Phone Installation Guide Version 1.0 [Table 4-17] Description of Static IP Menu Option Menu Options Description IP Address Setting Ex> 172.20.1.100 Network Mask Setting Ex> 255.255.0.0 Default Router Setting Ex> 172.20.1.1 First DNS setting (this menu can be applied at IPv6 mode) Ex> 168.126.63.1 Second DNS Setting (Option) (this menu can be applied at IPv6 mode) Ex> 168.126.63.
AP-IP120 IP Phone Installation Guide Version 1.0 IPv4 Setting – PPPoE This is the WAN protocol which takes a dynamic IP address from the PPP Server. ADSL is one of the typical applications in which PPPoE is used.
AP-IP120 IP Phone Installation Guide Version 1.0 [Table 4-18] Description of PPPoE Setting Menu Detail Menu Detail Description Enter a user name Ex> Addpac Enter a user password Ex> 1234 Enter an authentication mode, “PAP/CHAP” using alphanumeric key * Press F4 key to change the input mode from the number to English or English to number.
AP-IP120 IP Phone Installation Guide Version 1.0 Network Setup– LAN This LAN menu option is used for protocol setting of AP-IP120 second LAN interface which is used to connect PC or Ethernet Hub. None, DHCP for single (1) PC, DHCP for multiple PC are available as protocols for second fast ethernet LAN port.
AP-IP120 IP Phone Installation Guide Version 1.0 [Table 4-19] Description of LAN Setup Menu Option Menu Option Description Set LAN to the factory default mode. The default is set to NAT.
AP-IP120 IP Phone Installation Guide Version 1.0 Configure Lan Setup to Bridge mode.
AP-IP120 IP Phone Installation Guide Version 1.0 Network Setup– VoIP Setup This VoIP setup menu is used for SIP/H.323 VoIP signaling inter-working parameter setting between SIP server, Gatekeeper and AP-IP120 IP Phone..
AP-IP120 IP Phone Installation Guide Version 1.0 VoIP Setup – Signaling Setup This menu is used for VoIP signaling setup such as H.323, SIP protocol. There are 2 different ways: connecting directly to VoIP network and connecting indirectly through SIP proxy server. Each way needs the different optional settings.
AP-IP120 IP Phone Installation Guide Version 1.
AP-IP120 IP Phone Installation Guide Version 1.0 [Table 4-20] Description of SIP Protocol Menu Detail Menu Detail Description Enter a username for SIP server registration Enter a user password for SIP server registration. Enter a primary server IP address or domain of SIP server. Enter a secondary server IP address or domain of SIP server. Select ON/OFF mode whether E.
AP-IP120 IP Phone Installation Guide Version 1.0 VoIP Setup– QoS QoS sets a limit to transmitting voice packet within the bandwidth which is guaranteed by the network capacity.
AP-IP120 IP Phone Installation Guide Version 1.
VoIP Setup–SIP Options These menu options are to set up other supplementary functions and options of SIP protocol in addition. These options need to be setup basing on the network settings.
AP-IP120 IP Phone Installation Guide Version 1.0 [Table 4-22] Description of SIP Option Menu Option Menu Option Description Select the call-transfer mode. basic/attend. Enter VoIP Tag for conference service Enter conference service name Enter firewall address to check the public IP address when AP-IP120 is used under NAT/Firewall network environment. Transfer RTP Session information to listen Inband Ringbacktone of Public network under NAT/Firewall environment.
AP-IP120 IP Phone Installation Guide Version 1.0 Set Session Timer SIP UA Retry Counter sets SIP INVITE re- transmission count when AP-IP120 is dial-out. When there is fault on network or network quality is not good, Trying message of INVITE message will be delayed. In this case AP-IP120 transfer next INVITE message. Default is 10 and usually set as ‘3.’ When user-name is not number but characters, apply to register message. When called party is not number but characters, this option is used.
AP-IP120 IP Phone Installation Guide Version 1.0 Set the DNS SRV. When user-name is not number but characters, this option is used to register SIP server.
AP-IP120 IP Phone Installation Guide Version 1.0 VoIP Setup– PSTN Prefix When user wants to access the FXO interface for PSTN backup, this prefix number is used as PSTN access code. Additionally, AP-IP120 IP phone supports the PSTN back-up service when VoIP service is impossible due to network failure or VoIP call service is interrupted by an accident.
AP-IP120 IP Phone Installation Guide Version 1.0 VoIP Setup– Phone Number This menu is used for E.164 AP-IP120 Number Assignment. (Figure 4-35) Phone Number Menu Option [Table 4-24] Description of VoIP Menu Option Menu Detail Description Enter the E.164 Phone Number.
AP-IP120 IP Phone Installation Guide Version 1.0 VoIP Setup – Area Code In this menu option, the user can specify an area code.
AP-IP120 IP Phone Installation Guide Version 1.0 Network Setup – SSCP (Smart Service Control Protocol) SSCP Smart Service Control Portocol) is the AddPac proprietary protocol operates between the AddPac IP-PBX systems and IP terminals. The IP-PBX systems support many different call features, through SSCP, in addition to the basic call features of the IP Phone itself. The IP terminals take these call features supported by the IP-PBX, then it display these features on its softkeys.
AP-IP120 IP Phone Installation Guide Version 1.0 [Table 4-26] Description of SSCP Setup Menu Option Menu Option Description Either enable or disable the setting mode of SSCP Make a selection of Call-Manager Setup Configure the Call Manager server: 5 servers can be configured redundancy, 2 at Call maximum.
AP-IP120 IP Phone Installation Guide Version 1.0 Network Setup– Presence Presence menu section provides the user presence service from Smart Multimedia Manager which operates in MS Window-based PC Platform environment as to interwork with the AddPac IP-Next PBX. Interworking with Presence Server (integrated in IP-PBX), the user presence can be used by Smart Messenger which is PC-based and Speed Button List in the terminal.
AP-IP120 IP Phone Installation Guide Version 1.0 (Figure 4-38) Presence Menu Section [Table 4-27] Description of Presence Menu Option Menu Option Description Enable or disable the presence server Setup (Enable/Disable) Presence User정보를 입력하는 메뉴입니다.
AP-IP120 IP Phone Installation Guide Version 1.0 Presence Server에 등록 된 ID를 입력합니다. Presence Server에 등록 된 ID에 해당하는 Password를 입력합니다. Presence Server를 설정하는 메뉴입니다. 등록 할 Presence Server를 설정합니다. 선택한 Presence Server의 IP, Port정보를 입력합니 다.
AP-IP120 IP Phone Installation Guide Version 1.0 Network Setup – Service This menu enables or disables FTP, TELNET, TFTP, SNMP protocol service of AP-IP120. You can use FTP to access to AP-IP300 from a remote location and Telnet is used for changing all kinds of information and monitoring and SNMP is also used to access to AP-IP120 from a remote location.
AP-IP120 IP Phone Installation Guide Version 1.0 [Table 4-28] Description of Service Setup Menu Option Menu Option Description Actives/Deactivates the FTP service protocol. Default is enable mode (activating FTP service). Default port number is 21. Actives/Deactivates the TELNET service protocol. Default is enable mode (activating TELNET service). Default port number is 23. Actives/Deactivates the SNMP service protocol. Default is enable mode (activating SNMP service).
AP-IP120 IP Phone Installation Guide Version 1.0 Network Setup – Status This setup allows you to see the current status of the network on the screen such as Link Status , IPv4 Protocol, IPv4 address, Lan address, DNS, SIP Proxy Server, status of registration to GK[H.323], at a glance.
AP-IP120 IP Phone Installation Guide Version 1.
AP-IP120 IP Phone Installation Guide Version 1.
AP-IP120 IP Phone Installation Guide Version 1.0 Applications Menu Category Applications composed of a group of the call features including Message Box, Voice Mail Box, Conference. You can use Message Box and Voice Box only when they are connected to and supported by SSCP. You can make Conference calls on when they are connected to and supported by Multipoint Control Unit (MCU).
AP-IP120 IP Phone Installation Guide Version 1.0 Applications – Message Box The Message Box allows you to transmit and verify SMS text messages between one terminal and the other, when it is connected to SSCP.
AP-IP120 IP Phone Installation Guide Version 1.
AP-IP120 IP Phone Installation Guide Version 1.0 Write SMS (Figure 4-44) Write SMS Menu Option [Table 4-31] Description of Write Message Menu Detail Menu Detail Description Enter the messages in this field. (F4 : Changing from the alphabetic characters to the numeric and the numeric to the alphabetic) Enter the sender’s telephone number to be displayed on the receiver’s phone.
AP-IP120 IP Phone Installation Guide Version 1.
AP-IP120 IP Phone Installation Guide Version 1.
Saved (Figure 4-46) SMS Saved Menu Option [Table 4-33] Description of Saved Menu Detail Menu Option Description [1/2] : the first message of the 2 messages received and stored Seoul: the name of the sender 1003: the sender’s telephone number Hello~~ : the content of the message Read: to read the selected message Dele: to delete the selected message
Sent (Figure 4-47) Sent Menu Option [Table 4-34] Description of Sent Menu Option Menu Detail Description [1/2] : the first message of the 2 messages sent and stored Seoul: the sender’s name 1003: the sender’s telephone number Hello~~ : the content of the message Read: to read the selected message Dele: to delete the selected message
AP-IP120 IP Phone Installation Guide Version 1.0 Application – Voice Mail Box Voice Mail Box enables you to check the voice message as it interworks with SSCP.
AP-IP120 IP Phone Installation Guide Version 1.0 [Table 4-35] Description of Voice Mail Box Menu Option Menu Option Description This is the box to where the sent voice messages are kept This is where to keep the voice message which is saved.
AP-IP120 IP Phone Installation Guide Version 1.0 Applications – Conference This feature enables you to see the list of connections can be made for a conference call at the present time and you can join the conference by just pressing call button.
AP-IP120 IP Phone Installation Guide Version 1.
AP-IP120 IP Phone Installation Guide Version 1.0 System Setup Menu Category The system setup includes the Display Name, Ring volume control, input/output volume control.
AP-IP120 IP Phone Installation Guide Version 1.0 System Setup – Display Name This is Name displayed on LCD panel. Default name is AP-IP120. If user wants to change default name, change or modify the default name at Display Name in System Setup Menu. (Figure 4-52) Display Name Menu Section [Table 4-37] Description of Display Name Menu Option Menu Option Description Enter the Name you want (ex: Phone number, room number, office name).
AP-IP120 IP Phone Installation Guide Version 1.0 System Setup – Volume Control This volume menu controls the Ring volume, Input/Output volume (Speaker volume, Handset volume) of AP-IP120 IP Phone.
AP-IP120 IP Phone Installation Guide Version 1.0 [Table 4-38] Description of Volume Setup Menu Option Menu Option Description Select the ring volume of internal speaker. Default ring volume level is 4. Select the input volume of Speaker Phone or Handset MIC. The default is set to the level 4. Select the output volume of Speaker Phone or Handset Speaker. The default is set to the volume level 4.
AP-IP120 IP Phone Installation Guide Version 1.0 System Setup – Forward Setup (SIP) During the user’s to take a call, he/she uses this menu option to configure the incoming call arriving on FXO to be transferred to VoIP call (during the one’s absence, this forwarding feature is not supported for the incoming VoIP call).
AP-IP120 IP Phone Installation Guide Version 1.
AP-IP120 IP Phone Installation Guide Version 1.0 System Setup – Forward Setup (SSCP) This is the menu option to configure the call forward to redirect no matter what, either the user in the conversation on call or no response to the call.
AP-IP120 IP Phone Installation Guide Version 1.
AP-IP120 IP Phone Installation Guide Version 1.
AP-IP120 IP Phone Installation Guide Version 1.0 System Setup – Call Wait Setup (SSCP) Call Wait feature enables you to receive a second incoming call with on the same line without disconnecting the first call. This call feature allows you to receive an auditory call alert while you are on the first call. You can place the first on Hold and wait and connect to the second call. You can even return to the first call after you finish conversation with the second call.
AP-IP120 IP Phone Installation Guide Version 1.
AP-IP120 IP Phone Installation Guide Version 1.0 System Configuration – DND(Do Not Disturb) Setup Do Not Disturb (DND) features allows you to turn off the ringer (Ring Silence) for an incoming call or to reject the call (Call Reject. You may hold pressing the leave of absence button of the IP-Phone for more than 2 seconds to enable or disable this function. The Call Reject can work only in the SSCP mode.
AP-IP120 IP Phone Installation Guide Version 1.
AP-IP120 IP Phone Installation Guide Version 1.
AP-IP120 IP Phone Installation Guide Version 1.0 System Setup – My Number My Number allows you to set the native number for the Outbound Call, as to select the one number among many numbers that have been assigned. You can take many numbers of incoming calls, but you can send only the predetermined number of the outgoing call at the default setting.
AP-IP120 IP Phone Installation Guide Version 1.0 [Table 4-44] Description of My Number Menu Option Menu Option Description This is an example for assignment of the 2 telephone numbers. The default setting is set to 1000.
AP-IP120 IP Phone Installation Guide Version 1.0 System Setup – Voice Class Codec The audio codec of AP-IP120 determines the voice codec. You can choose the options of G.711[PCM] and G726, G.729, and G.723.1 on OSD, basing on the priority level which can be suitable to your network settings.
AP-IP120 IP Phone Installation Guide Version 1.0 [Table 4-45] Description of Voice Codec Menu Option Menu Option Description Select Preference 1 of voice codec Specify the voice codec to Preference 1. (Default : G711ullaw) Select Preference 2 of voice codec. Specify the voice codec to Preference 2.
AP-IP120 IP Phone Installation Guide Version 1.0 Specify the voice codec to Preference 3. (Default : G729) Select Preference 3 of voice codec. Specify the voice codec to Preference 3.
AP-IP120 IP Phone Installation Guide Version 1.0 System Setup – Auto Answer This feature allows your telephone to answer a call automatically and you do not have to pick up the phone. You can set the interval of answering a call selectively: 3, 5, 10 or 15 seconds.
AP-IP120 IP Phone Installation Guide Version 1.0 [Table 4-46] Description of Auto Answer Menu Option Menu Option Description Disable Auto Answer Receive the call at the first ring Set the mode to Auto Answer to reply on 3 seconds after the bell rings. Set the mode to Auto Answer to reply on 5 seconds after the bell rings. Set the mode to Auto Answer to reply on 10 seconds after the bell rings.
AP-IP120 IP Phone Installation Guide Version 1.0 Set the mode to Auto Answer to reply on 15 seconds after the bell rings.
AP-IP120 IP Phone Installation Guide Version 1.0 System Setup – Hook Setup Hook is the feature that allows you to disconnect the phone even when the other part did not hang up the line. This feature is supported by SSCP.
AP-IP120 IP Phone Installation Guide Version 1.
AP-IP120 IP Phone Installation Guide Version 1.0 System Setup – Emergency If a terminal limits an outgoing call due to Administrator/ User Lock, the terminal can be configured to take an emergency call. For the phone number specified in Emergency menu section, the outgoing call can be sent out regardless of lock status.
AP-IP120 IP Phone Installation Guide Version 1.
AP-IP120 IP Phone Installation Guide Version 1.0 Chapter 5. Additional Features for FXO Forward Setup (SIP) This feature allows you to set to change a incoming call on FXO to VoIP, when you are available to take the call.
AP-IP120 IP Phone Installation Guide Version 1.0 [Table 5-1] Description of Forward Setup Menu Option Menu Option Description Set the telephone number to where the call is to be forwarded Determine whether to assign the number of Speech port (the predetermined number of AP-IP120) or the number of the incoming call on FXO (The default setting is set to On), when the call is forwarded.
AP-IP120 IP Phone Installation Guide Version 1.0 Call Waiting (SIP) For any incoming call arriving to FXO can be placed on hold while the phone user is on another VoIP call. While the phone user is on PSTN call, any incoming VoIP call can be placed on hold as well. Call-waiting needs to be configured on speech port and call-hold h also needs to be configured at the configuration mode.
AP-IP120 IP Phone Installation Guide Version 1.0 ! FXS voice-port 0/1 ! ! Pots peer configuration. ! dial-peer voice 0 pots destination-pattern 1004 port 0/0 call-waiting ! ! Voip peer configuration.
AP-IP120 IP Phone Installation Guide Version 1.0 Chapter 6. Testing Operation Booting Procedure and Operating Bases The things that you have to know, prior to turning on the power of AP-IP120, are the booting procedure. • AP-IP120 checks its basic operation of its interface, memory and CPU through a self-testing procedure • After the Boot Loader is started, the IP120 looks for the appropriate software image file.
AP-IP120 IP Phone Installation Guide Version 1.0 Using HyperTerminal for the Console Terminal Terminal Emulator Application must be installed for using the PC for the console terminal. HiperTerminal Application is used for MS-Windows. (Figure 6-1) Terminal Emulator HyperTerminal on MS-Windows After HyperTerminal is performed, determine the name of the new connection. The user can decide the name of the connection.
AP-IP120 IP Phone Installation Guide Version 1.
AP-IP120 IP Phone Installation Guide Version 1.0 Select the interface of which the console cable is connected Since AP-IP120 does not support Console Interface, the IP Address of LAN1 interface is used to connect PC as it is shown in the following figure: (LAN1 default ip address : 192.168.10.1) Access after the IP address of 192.168.10.100 for the PC is set.
AP-IP120 IP Phone Installation Guide Version 1.0 After completing the setup, you can see the login screen of AP-IP120 in the following Figure (Figure 6-4) Login Screen You may see the 2 types of prompt: ‘AP-IP120>’ and ‘AP-IP120#’. The prompt with starting with ‘>’ means that the user, who logged in, has the least privilege of ‘admin’ only. He/she is not allowed to change the settings of the IP Phone. The prompt with ‘#’ means that the user, who logged in, had the privilege of ‘admin’.
AP-IP120 IP Phone Installation Guide Version 1.0 Using APOS Commands NOTE All the product lines of AddPac Technology are imbedded with APOS AddPac Operating System).
AP-IP120 IP Phone Installation Guide Version 1.0 General User Mode Commands These are the functions that all the types of the users who logged in the system The prompt for the general user can be indicated as ‘ip-120>’.
AP-IP120 IP Phone Installation Guide Version 1.0 Management Mode Commands These are the types of commands that the administrator, whoever logged in the system, can use. To get into configuration of this system mode, the user must be logged in as an administrator. In this mode, the commands can be same as General User mode such as ‘show’, but more information can be shown depending on the option. The prompt of Management Mode can be indicates as ‘IP120#’.
AP-IP120 IP Phone Installation Guide Version 1.
AP-IP120 IP Phone Installation Guide Version 1.0 Basic Configuration Configuring Password After a connection is established to the console, the user can only have the basic show command. To gain more privilege to access, the user has to enter enable mode. When the general use enter enable mode, he/she gains the all the privilege to change the system configuration. Therefore it is important to set the password, so only the administrator can enter to configure the settings.
AP-IP120 IP Phone Installation Guide Version 1.
AP-IP120 IP Phone Installation Guide Version 1.0 Configuring FXS/FXO Port * Configuring after the Display of show run [Table 6-6] Configuring FXS/FXO Port IP120# show run Building configuration... Current configuration: version 8.41.015 hostname IP120 ! username root password router administrator ! interface Loopback0 ip address 127.0.0.1 255.0.0.0 ! interface FastEthernet0/0 ip address 172.17.201.88 255.255.0.0 ip nat outside speed auto no qos-control ! interface FastEthernet0/1 ip address 192.168.10.
AP-IP120 IP Phone Installation Guide Version 1.0 ! Pots peer configuration. ! dial-peer voice 0 pots destination-pattern 1004 port 0/0 ! IP120# IP120# con t IP120(config)# dial-peer voice 1 pots => FXS/FXO port dial peer configuration IP120(config-dialpeer-pots-1)# destination-pattern 1014 => Assigning the port numbers of FXS/FXO IP120(config-dialpeer-pots-1)# port 0/1 => Assigning the port that has been checked IP120# show run (checking the configuration) Building configuration...
AP-IP120 IP Phone Installation Guide Version 1.0 --- 중략 ----! ! Voice port configuration. ! ! SPEECH voice-port 0/0 ! ! FXS voice-port 0/1 ! ! Pots peer configuration.
AP-IP120 IP Phone Installation Guide Version 1.0 Chapter 7. Emergency Recovery The entire AddPac VoiIP product line has 2 different zones. One is to store APOS and Boot Loader is the other. The functions of Boot Loader can be used in the followings: 1. Loss of the password for the root account 2. Damage or erase of the software in APOS image You can recover the Default IP by resetting APOS settings in case you lost or change the Default IP(192.168.10.1) AP-IP120 which can be accessed by TELNET, FTP.
AP-IP120 IP Phone Installation Guide Version 1.0 Entering the mode of Boot Loader Since AP-IP120 does not have console interface, it is not possible to enter the mode of Boot Loader by using ‘ctrl+x’, ctrl+c’ , which is possible for APOS with presence of console such as ‘send break’., during the booting process. During the booting process, AP-IP120 checks the basic operation of CPU, memory and interface. Then it waits for about 3 seconds for the user to make an access.
AP-IP120 IP Phone Installation Guide Version 1.0 Initialize APOS Settings When the user lost the default IP address of the IP Phone (192.168.10.1) that enables TELNET and FTP access, after making a change, the default IP can be recovered by initializing APOS settings (Please be cautious when you initializes APOS configuration, all the existing settings of configuration are to be erased.) You can initialize APOS settings by TELNET access. D:\> D:\> telnet 192.168.10.1 Welcome, APOS™ Boot Kernal Version 5.
AP-IP120 IP Phone Installation Guide Version 1.0 Downloading APOS Image File in Boot Loader Mode The AddPac AP-IP120 IP Phone allows FTP access, which is supported by the binary code, to transmit APOS image file. APOS image of AP-IP120 can be downloaded from PC by using FTP. D:\ >dir 2006-05-15 05:21p
. 2006-05-15 05:21p .. 2006-05-15 05:21p 1,775,360 AP-IP120_g2_v8_41_015.bin D:\> D:\> ftp 172.17.201.88 Connected to 172.17.201.88. 220 IP120 FTP server (Version 8.41.015) ready.AP-IP120 IP Phone Installation Guide Version 1.0 Chapter 8. Appendix This Appendix provides information about the Pinout specifications of the following cables used with AP-IP120 IP Phone. z Console Port Signal and Pinout (RJ-45 to DB9) z Ethernet UTP Cable Assemble (RJ-45 to RJ-45) Pinout [RS-232C Console Port Signal & Pinout ] In order to connect RS-232C console port with the Terminal Emulating PC, the RJ-45 to DB9 (Female DTE Connector) cable is used.
AP-IP120 IP Phone Installation Guide Version 1.0 [UTP Cable (RJ-45 to RJ-45) Pinout Specification] In order to connect the LAN port of this equipment with other equipments (i.e. HUB), the RJ-45 to RJ-45 Ethernet Cable is used. The RJ-45 Connector Pin sequence is provided below and the signal and Pinout specifications are enlisted at the below table.
AP-IP120 IP Phone Installation Guide Version 1.0 Acronyms and Glossary Terms Definition & Description ADSL An acronym for Asymmetric Digital Subscriber Line, ADSL is a method of transmitting data over traditional copper telephone lines. Data can be downloaded at speeds of up to 1.544 Megabits per second and uploaded at speeds of 128 Kilobits per second (asymmetric). An acronym for VoIP Plug & Play Management Software.
AP-IP120 IP Phone Installation Guide Version 1.0 used by cable TV provides much greater bandwidth than telephone lines, a cable modem can be used to achieve more bandwidth. Cable network also requires modularization and demutualization process while sending the data. Call Center A call center is a central place where customer and other telephone calls are handled by an organization, usually with some amount of computer automation.
AP-IP120 IP Phone Installation Guide Version 1.0 CODEC An acronym for COder-DECoder 1. Built-in circuit device for coding/decoding of analog signal to bit stream with Pulse Code Modulation method. 2. DSP software algorithm for compressing/ decompressing voice or audio signal Console DTE interface whether the command is delivered to the host.
AP-IP120 IP Phone Installation Guide Version 1.0 machine via telephone line. The transmission and the reproduction at a distance of still pictures printed matter and similar documented material Frame data that is transmitted between network points as a unit complete with addressing and necessary protocol control information. A frame is usually transmitted serial bit by bit and contains a header field and a trailer field that "frame" the data. (Some control frames contain no data.
AP-IP120 IP Phone Installation Guide Version 1.0 devices in the multimedia network. The devices register with the gatekeeper at startup and request admission to a call from the gatekeeper. H.225 An International Telecommunication Union (ITU-T) standard session control and packetization. for H.225.0 It defines various protocols of RAS, Q.931, RTP and etc. H.245 An International Telecommunication Union (ITU-T) standard for H.245 endpoint control. H.
AP-IP120 IP Phone Installation Guide Version 1.0 the Internet Protocol. Users and service providers can update to IPv6 independently without having to coordinate with each other. ISP An ISP (Internet service provider) is a company that provides individuals and other companies access to the Internet and other related services such as Web site building and virtual hosting.
AP-IP120 IP Phone Installation Guide Version 1.0 MAN A data network designed for a town or city. MANs are considered larger than LANs but smaller than WANs. Compare with: LAN, WAN. MGCP MGCP, also known as H.248 and Megaco, is a standard protocol for handling the signaling and session management needed during a multimedia conference.
AP-IP120 IP Phone Installation Guide Version 1.0 superseding the SLIP protocol, PPP establishes the session between the user's computer and the ISP using its own Link Control Protocol (LCP). PPP supports PAP, CHAP and other authentication protocols as well as compression and encryption. Protocol Stack Any set of communication protocols, such as TCP/IP, that consists of two or more layers of software and hardware.
AP-IP120 IP Phone Installation Guide Version 1.0 servers, and routers. Uses delay as a routing metric. Refer to: SRTP. 2. Rapid Transport Protocol. Provides pacing and error recovery for APPN data as it crosses the APPN network. With RTP, error recovery and flow control are done end-to-end rather than at every node. RTP prevents congestion rather than reacts to it. 3. Real-Time Transport Protocol. Commonly used with IP networks.
AP-IP120 IP Phone Installation Guide Version 1.0 T1 A TDM physical transmission standard consisting of two twisted wire pairs and related equipment capable of carrying a 1.544 Mbps DS-1 signal. Term often used interchangeably with DS-1. Refer to: AMI, B8ZS, DS-1. TCP/IP Transmission Control Protocol/Internet Protocol, The protocol suit developed by DoD (USA) in 1970s for the worldwide inter-network development. TCP & IP is the most well known protocols of the suite. Telco Refer to: IP, TCAP.
AP-IP120 IP Phone Installation Guide Version 1.0 VoIP VoIP (Voice delivered using the Internet Protocol) is a term used in IP telephony for a set of facilities for managing the delivery of voice information using the Internet Protocol (IP). In general, this means sending voice information in digital form in discrete packets rather than in the traditional circuit-committed protocols of the public switched telephone network (PSTN).
AP-IP120 IP Phone Installation Guide Version 1.0 AddPac Technology Co., Ltd. 2F & 3F, Jeong-Am Bldg., 769-12 Yeoksamdong, Gangnam-gu, Seoul, 135-080, Korea Tel: +82 2 568 3848 Fax: +82 2 568 3847 Email: sales@addpac.com http:// www.addpac.
