Specifications
SATA-IO Confidential 7
2.15.2. RX-02 : Single-Ended Impedance (Obsolete) ....................................................................................... 60
2.15.3. RX-03 : Gen2 (3Gb/s) Differential Mode Return Loss .......................................................................... 60
2.15.4. RX-04 : Gen2 (3Gb/s) Common Mode Return Loss ............................................................................. 61
2.15.5. RX-05 : Gen2 (3Gb/s) Impedance Balance .......................................................................................... 61
2.15.6. RX-06 : Gen1 (1.5Gb/s) Differential Mode Return Loss ....................................................................... 62
2.16. Phy Receive Signal Requirements ............................................................................................................... 62
2.16.1. RSG-01 : Gen1 (1.5Gb/s) Receiver Jitter Tolerance Test .................................................................... 63
2.16.2. RSG-02 : Gen2 (3Gb/s) Receiver Jitter Tolerance Test ....................................................................... 64
2.17. Phy OOB Requirements ............................................................................................................................... 64
2.17.1. OOB-01 : OOB Signal Detection Threshold .......................................................................................... 64
2.17.2. OOB-02 : UI During OOB Signaling ...................................................................................................... 65
2.17.3. OOB-03 : COMINIT/RESET and COMWAKE Transmit Burst Length .................................................. 66
2.17.4. OOB-04 : COMINIT/RESET Transmit Gap Length ............................................................................... 66
2.17.5. OOB-05 : COMWAKE Transmit Gap Length ........................................................................................ 67
2.17.6. OOB-06 : COMWAKE Gap Detection Windows ................................................................................... 67
2.17.7. OOB-07 : COMINIT/COMRESET Gap Detection Windows .................................................................. 69
2.18. Port Multiplier Requirements (informative) ................................................................................................... 71
2.18.1. PM-01 : Device Port 0 Enabled by Default............................................................................................ 71
2.18.2. PM-02 : General Status and Control Register (GSCR) Access ............................................................ 72
2.18.3. PM-03 : Port Status and Control Register (PSCR) Access ................................................................... 73
2.18.4. PM-04 : 3Gb/s Backwards Compatibility ............................................................................................... 74
2.18.5. PM-05 : Interface Power Management, H – PM, Host Initiated ............................................................ 74
2.18.6. PM-06 : Interface Power Management, H - PM, PM Initiated ............................................................... 76
2.18.7. PM-07 : Interface Power Management, PM - Dev, PM Initiated ........................................................... 77
2.18.8. PM-08 : Interface Power Management, PM - Dev, Dev Initiated .......................................................... 78
2.18.9. PM-09 : Speed matching upon resume (H-PM interface) ..................................................................... 80
2.18.10. PM-10 : Speed matching upon resume (PM-Dev interface) ................................................................. 81
2.18.11. PM-11 : Port Multiplier Reset Response ............................................................................................... 83
2.18.12. PM-12 : Device Port 0 Hot Plug with non-PM aware host software. ..................................................... 84
2.18.13. PM-13 : Hot Plug with PM aware host software. ................................................................................... 84
2.18.14. PM-14 : FIS Sent To a Disabled Device Port. ....................................................................................... 85
2.18.15. PM-15 : FIS Sent To a Invalid Device Port Address. ............................................................................ 85
2.18.16. PM-16 : Test For PM-aware Host ......................................................................................................... 86
3. System Interoperability Tests .................................................................................................................................. 87
3.1. System Description .......................................................................................................................................... 87
3.1.1. System Product Selection ......................................................................................................................... 87
3.1.2. System Interoperability non-PUT Cable requirements ............................................................................. 87
3.1.3. System Interoperability Host Requirements for Device testing ................................................................ 87
3.1.4. System Interoperability Device Requirements for Host testing ................................................................ 88
3.2. System Interoperability Test Description ......................................................................................................... 88
3.2.1. Resource requirements ............................................................................................................................. 88
3.2.2. SYS-01: System Interoperability Test Requirements ............................................................................... 89
3.2.3. System Interop Pass / Fail Criteria ........................................................................................................... 90
3.3. System Interoperability Test Tool Validation requirements ............................................................................. 90
3.3.1. SYT-01 – Data pattern validation .............................................................................................................. 90
3.3.2. SYT-02 – Data pattern alignment ............................................................................................................. 91
3.3.3. SYT-03 – 8 KB Data FIS usage ................................................................................................................ 91
3.3.4. SYT-04 – Data error detection .................................................................................................................. 91
3.3.5. SYT-05 – Complete Data set, including Host caching and retries............................................................ 91
3.3.6. SYT-06 - Data file signatures .................................................................................................................... 92
3.3.7. SYT-07 - Data Pattern set......................................................................................................................... 92
3.3.8. SYT-08 - Test duration .............................................................................................................................. 92
3.3.9. SYT-09 – System Configuration ............................................................................................................... 92
3.3.10. SYT-10 – OS Install ............................................................................................................................... 92
4. Framed COMP Pattern ............................................................................................................................................ 93
4.1. SATA 2.6 ECN 009 Long FRAMED COMP Pattern ........................................................................................ 93