Datasheet

Ordering information
Specifications
APCI-2032 /APCI-2032-5
APCI-2032: Digital output board, optically isolated, 32 digital outputs, 24 V. Incl. technical description and software drivers
APCI-2032-5: Digital output board, optically isolated, 32 digital outputs, 5 V. Incl. technical description and software drivers
Accessories
PX901-D: Screw terminal panel, LED status display
PX901-DG: Same as PX901-D, for DIN rail
PX 901-ZG: Screw terminal panel (only APCI-2032-5)
PX9000: 3-row screw terminal panel
for DIN rail, LED status display
PX8500-G: Relay output board for DIN rail, cascadable
ST010: Standard round cable, shielded, twisted pairs, 2 m
ST011: Standard round cable, shielded, twisted pairs, 5 m
ST010-S: Same as ST010, for high currents (24 V supply separate)
ST022: Round cable between two PX8500-G, shielded, 2 m
ST8500: Ribbon cable for cascading two PX8500-G
Digital outputs
Outputs: 32
Output type: High-side (load to ground) acc. to IEC 1131-2
Optical isolation: through opto-couplers, 1000 V
from PC to peripheral
Nominal voltage: 24 V (APCI-2032); or 5 V (APCI-2032-5)
Supply voltage: for 24 V version: 10 V to 36 V
for 5 V version: 5 V to 12 V via front connector
Max. current for 32 outputs: 6 A typ. (2x3 A)
Output current: 500 mA max./channel
Short-circuit current/output
shutdown at 24 V, R
load
< 0.1 Ω: 1.5 A
RDS ON resistance: 0.4 Ω max.
Switch-on time: l out=0.5 A, load = resistance: 94 µs typ. (APCI-2032)
l out=50 mA, load = resistance: 250 µs typ. (APCI-2032-5V)
Switch-off time: l out=0.5 A, load = resistance: 8 µs typ. (APCI-2032)
l out=50 mA, load = resistance: 3 µs typ. (APCI-2032-5V)
Overtemperature (shutdown): 170 °C (output driver)
Temperature hysteresis: 20 °C (output driver)
Safety
Shut-down logic (V
cc
diagnostic): If the ext. 24 V voltage drops below 5 V,
then the outputs are switched off.
CC-Diagnostics: Pin 19: status bit or interrupt to the PC
Watchdog: 8-bit, programmable, 20 ms up to 5 s
in steps of 20 ms
EMC – Electromagnetic compatibility
The product complies with the European EMC directive. The tests were carried out by
a certied EMC laboratory in accordance with the norm from the EN 61326 series (IEC
61326). The limit values as set out by the European EMC directive for an industrial
environment are complied with. The respective EMC test report is available on request.
Physical and environmental conditions
Dimensions: 131 x 99 mm
System bus: PCI 32-bit 5 V acc. to specication 2.1 (PCISIG)
Space required: 1 PCI slot
Operating voltage: +5 V, ± 5 % from the PC
Current consumption: 230 mA ± 10 % typ.
Front connector: 37-pin D-Sub male connector
Temperature range: 0 to 60 °C (with forced cooling)
PCI bus
37-pin
D-Sub male
connector
PCI
interface
Output 0-7
Output 8-15
Output 16-23
Output 24-31
8 digital
outputs
8 digital
outputs
8 digital
outputs
8 digital
outputs
FPGA
Control
logic
Watchdog
Protective circuits and filters
Opto-coupers
Pin assignment – 37-pin D-Sub male connector
Example 2
Connection of the outputs
through relay output board PX8500-G
cascaded in 32 relays
Example 1
Connection of the outputs through screw terminal panels
D-Sub
female
connector
D-Sub
male
connector
D-Sub
female
connector
D-Sub
male
connector
D-Sub
male
connector
D-Sub
male
connector
PX8500-G
PX8500-G
PX8500-G
PX8500-G
PX901-DG
or
PX9000
ADDI-DATA connection
Simplified block diagram
Screw terminal panel PX901-DG
with cable ST010
Relay output board PX8500-G
171
Phone: [phone] info
@
addi-data.com
Fax: [phone] www.addi-data.com
PCI boards, digital I/O – APCI-2032 /APCI-2032-5