Datasheet

Specifications
Ordering information
Counter components
Counting depth: 32-bit, Counting frequency: up to 5 MHz
Free programming of the functions
32-bit or 16-bit acquisition of incremental encoders
Acquisition of absolute encoders/SSI
Counter/timer
Chronos/TOR for frequency measurement
Pulse acquisition
Chronos for pulse width modulation
Chronos for period duration measurement
TOR for velocity measurement
Digital I/O, 24 V, TTL, RS422
PWM
ETM
Customised functions
Signals
Digital I/O signals, TTL or RS422
Inputs
Number of inputs: 20
Differential inputs or outputs
5 V inputs: 8/16 (8 can be used as inputs or outputs)
Nominal voltage: 5 VDC
Common mode range: +12 / –7 V
Max. differential voltage ±12 V
Input sensitivity: 200 mV
Input hysteresis: 50 mV
Input impedance: 12 kΩ
Terminal resistor: 150 Ω serial with 10 nF (typ.)
Signal delay: 120 nS (at nominal voltage)
Max. input frequency: 2.5 MHz (at nominal voltage)
Mass-related inputs, 24 V (channels E, F, G):
Number of inputs: 12
Nominal voltage: 24 VDC
Input current: 11 mA (typical) at nominal voltage
Logic input levels: Unominal: 24 V
UH max.: 30 V
UH min.: 19 V
UL max.: 15 V
UL min.: 0 V
Signal delay: 120 ns (at nominal voltage)
Maximal input frequency: 1 MHz
Outputs
Nominal voltage: 5 VDC
Maximum output frequency: 2.5 MHz (diff. outputs)
Max. number of outputs: 8 (if they are not used as diff. inputs)
Digital outputs, 24 V:
Output type: High-side (load to ground)
Number of outputs: 4
Nominal voltage: 24 VDC
Range of the supply voltage: 10 V to 36 VDC (via 24 V ext. pin)
Maximum current
for 4 outputs: 2 A typ. (limited to the voltage supply)
Maximum output current: 500 mA short-circuit current/
output at 24 V, R
load
< 0.1 Ω: 1.5 A max. (output switches off)
ON-resistance of the output
(RDS ON resistance): 0.4 Ω max.
Overtemperature: 170 °C (all outputs switch off)
Overtemperature protection (24 V outputs)
Activated: From approx. 150-170 °C (chip temperature)
Deactivated (automatically): From approx. 125-140 °C (chip temperature)
Outputs (at overtemperature): Outputs switch off
Protection against undervoltage (effective at V ext.<5 V):
Outputs (at undervoltage): All outputs switch off
Switching characteristics of the 24 V outputs
(V ext. = 24 V, T=25 °C, ohmic load: 500 mA):
Switch ON time: 200 µs
Switch OFF time: 15 µs
Digital outputs, 5 V (option):
Output type: TTL
Number of outputs: 4
Nominal voltage: 5 VDC
Switching characteristics of the 5 V outputs (T=25 °C, TTL load):
Switch ON time: 0.06 µs
Switch OFF time: 0.02 µs
Technical data for the APCI-1710-24 V board version
24 V inputs (channels A to G). This board version is exclusively used for connecting 24 V
encoders. Only 24 V signals can be connected to the input channels.
Nominal voltage: 24 VDC / 10 mA
Max. input frequency: 1 MHz (at nominal voltage)
Logic input levels : U nominal: 24 V
(Standard) UH max.: 30 V
UH min.: 19 V
UL max.: 15 V
UL min.: 0 V
Safety
Optical isolation: 1000 V
EMC – Electromagnetic compatibility
The product complies with the European EMC directive. The tests were carried out by a
certied EMC laboratory in accordance with the norm from the EN 61326 series (IEC 61326).
The limit values as set out by the European EMC directive for an industrial environment are
complied with. The respective EMC test report is available on request.
Physical and environmental conditions
Dimensions: 179 x 99 mm
System bus: PCI 32-bit 5 V acc. to specication 2.1 (PCISIG)
Space required: 1 slot
Operating voltage: +5 V, ± 5 % from the PC
+24 V ext. /10 mA
Current consumption: APCI-1710-x: 1.15 A typ. ± 10 %
Front connector: 50-pin D-Sub male connector
Additional connector: Male connector for the TTL I/O function
Temperature range: 0 to 60 °C (with forced cooling)
Option
Opt. 5V: 5 V outputs instead of 24 V (H0, H1, H2, H3)
Accessories
ST370-16: Shielded round cable, 2 m
PX8001: 3-row terminal panel for DIN rail
FB8001: Ribbon cable for connecting the TTL I/O function
APCI-1710
Multifunction counter board, optically isolated, encoder, incremental counter, timer/counter, SSI, PWM,...
Incl. technical description and software drivers.
APCI-1710: Multifunction counter board, optically isolated
APCI-1710-24V: 24 V for differential input signals (A and B for counter, I (Index) and UAS (error) signals)
APCI-1710-5V-I: 5 V inputs instead of 24 V (E, F, G)
APCI-1710-5V-I-0: 5 V inputs instead of 24 V (E, F, G), 5 V outputs instead of 24 V (H0, H1, H2, H3)
APCI-1710
ST370-16
FB8001
TTL I/O
PX8001
50-pin
D-Sub
female
connector
50-pin
D-Sub
male
connector
Pin 1
ADDI-DATA connection
Phone: [phone] info
@
addi-data.com
Fax: [phone] www.addi-data.com
186
PCI, counter – APCI-1710