User guide

17
HP ProCurve 2810 and 2910
Using Command Line Interface (CLI) will
provide access to the switch’s full set of
commands.
The settings below affect multicast
operation on the switch.
IGMP
IGMPcongurationisdisabledbydefault
onProCurve2810and2910switches.
• TodeterminethecurrentstatusofIGMP
use the command:
 showipigmpcong
• ToenableordisableIGMPusethe
command:
[no] ip igmp
• ToenableordisableIGMPQuerier
function use:
[no] ip igmp querier
Jumbo frames
Jumbo packet support is disabled by default
oonProCurve2810and2910switches.
• Todeterminethecurrentjumbo
congurationsettingusethecommand:
show vlans
• Toenableordisablejumbopacket
support issue the following command in
Manager level operation :
[no] vlan 1 jumbo
ThislistsstaticVLANsconguredon
the switch. The Jumbo column indicates
whetherthegivenVLANisconguredfor
Jumbo packets or not.
Spanning-Tree Protocol (STP)
STPisdisabledbydefaultonProCurve
2810and2910switches.
• TodeterminethecurrentSTP
congurationontheswitchusethe
command:
show spanning-tree
Switch setups
HuaWei Quidway s5328c-EI (Layer 3)
Youneedtocongurethefollowing:
• AssignswitchIPaddress
• EnableIGMPsnooping
• EnableIGMPsnoopingsend-query
• EnableIGMPquerier
• Enablemulticastdrop-unknown
Assign switch IP address
1 <Quidway> system-view
2 [Quidway]
3 [Quidway] interface vlanif 1
4[Quidway-Vlanif1]ipaddress{mask|
mask-length}
5 [Quidway -Vlanif1] quit
Enable IGMP snooping
1 [Quidway] igmp-snooping enable
2 [Quidway] vlan 1
3 [Quidway -Vlanif1] igmp-snooping enable
4 [Quidway -Vlanif1] quit
Enable IGMP snooping send-query
1 [Quidway] igmp-snooping send-query
enable
2 [Quidway] igmp-snooping send-query
source-address{vlanif1address}
Enable IGMP querier
1 [Quidway] vlan 1
2 [Quidway -Vlanif1] igmp-snooping
querier enable
3 [Quidway -Vlanif1] quit
Enable mulcast drop-unknown
1 [Quidway] vlan 1
2 [Quidway -Vlanif1] multicast drop-
unknown
3 [Quidway -Vlanif1] quit
4 [Quidway] quit
5 <Quidway> save
H3C 5120
<alif>dis cur
#
version5.20,Release2202P06
#
sysname alif
#
domain default enable system
#
telnet server enable
#
undo ip ttl-expires
#
igmp-snooping
#
vlan 1
igmp-snooping enable
igmp-snooping drop-unknown
igmp-snooping querier
igmp-snooping general-query source-ip
172.29.0.1
#
radius scheme system
server-type extended
primaryauthentication127.0.0.11645
primaryaccounting127.0.0.11646
user-name-format without-domain
#
domain system
access-limit disable
state active
idle-cut disable
self-service-url disable
#
user-group system
#
interface NULL0
#
interface Vlan-interface1
ipaddress172.29.0.1255.255.255.0
#
interfaceGigabitEthernet1/0/1
#
interfaceGigabitEthernet1/0/2
#
interfaceGigabitEthernet1/0/3
#
interfaceGigabitEthernet1/0/4
#