AdderLink X-DVIPRO Digital video and USB extenders
Further information Troubleshooting.........................................................................11 Getting assistance.......................................................................11 Warranty.....................................................................................12 Safety information.....................................................................12 Radio Frequency Energy............................................................13 Connections................
CAT7a - 50m max CAT6 - 45m max CAT5e - 35m max Additional CATx link on MS2 variants X-DVIPRO link with direct cable connection Additional video channel and dual stereo audio channels on MS2 variants X-DVIPRO Local Patch lead <2m max Patch lead <2m max X-DVIPRO Remote Patch panel Patch panel Additional CATx link on MS2 variants X-DVIPRO Remote X-DVIPRO Local X-DVIPRO link with cable and patch panel connections Additional video channel and dual stereo audio channels on MS2 variants
What’s in the box Additional 12.5W power adapter and country- specific power lead Local module Remote module AdderLink X-DVIPRO standard modules Video cable DVI/D to DVI/D USB cable 2m (type A to B) Eight self-adhesive rubber feet CD-ROM The MS2 variant package includes all of the above ancillary items plus: Local module Remote module Additional USB cable 2m (type A to B) Additional video cable DVI/D to DVI/D 3.
What you may additionally need Power adapter and countryspecific power lead for X-DVIPRO local module, if powering via the USB port is not possible. In such cases, two power adapters are required for X-DVIPRO-MS2 local modules. Part number: PSU-IEC-5VDC-2.5A Rack mount kit for X-DVIPRO Part number: X-RMK-FASCIA Rack mount chassis Part number: X-RMK-CHASSIS Extra 3.
Installation Desk mount Apply the supplied self-adhesive rubber feet to the underside of the module. The X-DVIPRO and X-DVIPRO-MS2 modules can be situated on a desk or alternatively, for larger installations, mounted within an optional rack mount chassis. Mounting the modules – desk or rack Rack mount 1 Place the rack securing plate (available as a separate kit) onto the front of the module and secure it with the two countersunk screws.
Connections at the local module 3 Use the supplied USB cable to link the USB socket of the local module to a vacant USB socket on the computer. Note: Do not use USB cables longer than 3 metres to connect the local module to the computer. 1 Where possible, ensure that power is disconnected from the computer system to be connected. 2 Use the supplied DVI/D link cable to connect the DVI input socket of the local module to the digital video output socket of the computer.
4 Connect the link cable (see page 2 for cable advice) to the local module socket labelled TO REMOTE. Power connection The X-DVIPRO local module is designed to derive its power from the host computer via the USB connection (two USB connections in the case of the MS version). If this is not possible, then you will need to use one or two optional Adder power adapter(s).
Connections at the remote module To keyboard, mouse and other USB peripherals IMPORTANT: The total current that may be drawn from the USB ports is 1.2A, which should be sufficient for a keyboard, mouse (no more than 100mA each) and any two other devices (500mA maximum each). If more power for USB devices is required, please use a powered USB hub.
Power connection 1 Connect the output lead of the supplied power adapter to the socket labelled ‘POWER‘ on the remote module. 4 Connect the link cable (see page 2 for cable advice) to the remote module socket labelled TO LOCAL. X-DVIPRO: Output lead from the power adapter Primary CATx link cable X-DVIPRO-MS2: Output lead from the power adapter 2 Insert the IEC connector of the separate power lead into the corresponding socket of the power adapter.
Operation HDMI 1.3a operation Using optional HDMI to DVI converter cables (Adder part number: VSCD11), the AdderLink X-DVIPRO-MS can support HDMI video and audio up to the 165MHz clock rate (1920 x 1080 at 60Hz, 24-bit colour). Eight channels of HDMI audio are supported with sample sizes of 16, 20 or 24-bits at 32KHz, 44.1kHz, 48kHz, 88.2kHz, 96kHz, 176.4kHz, or 192kHz (simultaneously with the jack audio).
Further information • Email – support@adder.com • Fax in the UK: in the US: 01954 780081 +1 888 275 1117 • Phone in the UK: in the US: 01954 780044 +1 888 275 3337 • Adder Technology website – www.adder.com Check the Support section of our website for the latest solutions and driver files.
• For use in dry, oil free indoor environments only. • Do not use to link between buildings. • Ensure that the twisted pair interconnect cable is installed in compliance with all applicable wiring regulations. • Do not connect the CATx link interface (RJ45 style connector) to any other equipment, particularly network or telecommunications equipment. • Warning – the power adapter contains live parts.
Canadian Department of Communications RFI statement This equipment does not exceed the class A limits for radio noise emissions from digital apparatus set out in the radio interference regulations of the Canadian Department of Communications. Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la classe A prescrites dans le règlement sur le brouillage radioélectriques publié par le ministère des Communications du Canada.
Tel: +65 6288 5767 Fax: +65 6284 1150 Adder Asia Pacific 6 New Industrial Road, Hoe Huat Industrial Building #07-01, Singapore 536199 Adder Corporation, 350R Merrimac Street, Newburyport, MA 01950, United States of America Tel: +1-888-932-3337 Fax: +1-888-275-1117 Adder Technology Limited, Unit 5, Saxon Way, Bar Hill, Cambridge, CB23 8SL, United Kingdom Tel: +44 (0)1954 780044 Fax: +44 (0)1954 780081 © 2011 Adder Technology Limited All trad
