Owner's Manual

ManualsBrandsADD ManualsFront BumperADD 2021-2023 Ford Bronco Rock Fighter Winch Front Bumper

2021-Current Ford Bronco ADD Stealth Fighter ™

Rear Bumper Installation Instructions

Addictive Desert Designs® | Page 1

ADDICTIVE DESERT DESIGNSADDICTIVE DESERT DESIGNS®®

Preparation:

• Disconnect the negative battery terminal. Park the vehicle on level ground and set the emergency brake.

• We recommend reading through the installation instructions in whole before performing the work.

• When button head bolts are being used, install the supplied washer on the nut side. en, hold the bolt station-

ary and only turn the nut to tighten. Do not turn the bolt to tighten hardware assembly, unless otherwise noted.

• Estimated Installation Time: 2 Hours for OEM Removal/Bumper Installation

1 Additional Hour to Wire Lights

**This installation requires 2 people for best results**

**Labor Rates are based on a vehicle with no pre-existing damage. Wiring labor is based on a standard wiring procedure

with light switches installed in an easily accessible location. Custom light triggering or switch mounting location will

result in a greater labor charge.**

You will need the following tools:

- Ratchet - 9/16" Socket & Wrench - 13mm Socket

- 15mm Socket & Wrench - 18mm Socket - Long Ratchet Extension

-19mm wrench - Allen head 5/16 - 1 1/8 Socket & Wrench

Included in Kit:

4 - Hex Head Bolts

(3/8”-16 x 1 1/2")

9 - Black Oxide Flat Washers

(1/4")

4 - Extra Long Extended U nuts

(3/8”-16)

2 - Self Tapping Screws

(12"-1)

4 - Type A Washers

(3/8”)

2 - Nylon Lock Nut

(3/4"-10)

2 - Black Oxide Button Head Bolts

(1/2”-13 x 1 1/2")

2 - Flat Washer (

3/4")

2 - Black Oxide Nylon Lock Nut

(1/2”-13)

2 - Hex Head Bolts

(3/4”-10 x 1 1/2")

2 - Black Oxide Flat Washers

(1/2"-24 x 1 1/2")

2 - Black Oxide SAE Flat Washer

(5/16")

5 - Black Oxide Nylon Lock Nut

(1/4”-20)

2 - Black Oxide Nylon Lock Nut

(5/16"-18)

5 - Black Oxide Button Head Bolts

(1/4"-20 x 1")

2 - Black Rubber readed Bumper (1")

Summary of content (13 pages)

PAGE 1
® ADDICTIVE DESERT DESIGNS DESIGNS® ® 2021-Current Ford Bronco ADD Stealth Fighter ™ Rear Bumper Installation Instructions Preparation: • Disconnect the negative battery terminal. Park the vehicle on level ground and set the emergency brake. • We recommend reading through the installation instructions in whole before performing the work. • When button head bolts are being used, install the supplied washer on the nut side. Then, hold the bolt stationary and only turn the nut to tighten.
PAGE 2
® ADDICTIVE DESERT DESIGNS DESIGNS® ® 2021-Current Ford Bronco ADD Stealth Fighter ™ Rear Bumper Installation Instructions Removal: 1. Unplug the main bumper harness connectors located on both the driver and passenger side of the vehicle along the frame rail. There are 2 connectors in total located under the rear fenders. (Fig A) Fig A 2. Remove the 3 bolts with a 15mm wrench which will be found on each end of the bumper for a total of 6 bolts.
PAGE 3
® ADDICTIVE DESERT DESIGNS DESIGNS® ® 2021-Current Ford Bronco ADD Stealth Fighter ™ Rear Bumper Installation Instructions 3. There are 2 bolts which are 15mm that are located behind the bumper towards the inside of the frame. After those 2 bolts have been removed the bumper can be pulled off. (Fig C) Fig C 4. After the bumper is removed, take off the wiring harness by removing the sensor plugs and License plate light.
PAGE 4
® ADDICTIVE DESERT DESIGNS DESIGNS® ® 2021-Current Ford Bronco ADD Stealth Fighter ™ Rear Bumper Installation Instructions 5. Take off the sensor bezels from the stock OEM bumper by squeezing the black part and push out to pop them out then remove the white plastic cover to get them ready to put on the ADD bumper. (Fig E) Fig E 6.
PAGE 5
® ADDICTIVE DESERT DESIGNS DESIGNS® ® 2021-Current Ford Bronco ADD Stealth Fighter ™ Rear Bumper Installation Instructions 7. After the Sensor bezels have been installed you can transfer the wiring harness from the OEM bumper to the ADD bumper. You will notice that one inner sensor will not reach the bezel destination, you will need to open up the wiring harness by cutting it to get enough length to plug in the sensor in place.
PAGE 6
® ADDICTIVE DESERT DESIGNS DESIGNS® ® 2021-Current Ford Bronco ADD Stealth Fighter ™ Rear Bumper Installation Instructions 8. After the wiring harness has been transfered over, zip tie the harness to secure it in place, than insert the 4 provide nut tabs on the ADD Rock Fighter bumper in these locations. (Fig H) 2 on each side Fig H 9. Insert license plate light into license plate light cut out from the inside of the bumper. Then push the light into place from the outside of the bumper.
PAGE 7
® ADDICTIVE DESERT DESIGNS DESIGNS® ® 2021-Current Ford Bronco ADD Stealth Fighter ™ Rear Bumper Installation Instructions 10. Remove the 2 bolts in the frame of the bronco to install the bracket that will be used as a mounting point for the bumper, then after the bracket has been placed in the frame use the same bolts to attach the bracket to the frame.
PAGE 8
® ADDICTIVE DESERT DESIGNS DESIGNS® ® 2021-Current Ford Bronco ADD Stealth Fighter ™ Rear Bumper Installation Instructions 11. There is a bracket by the frame horn held in place by one bolt that needs to be removed shown below in. (Fig K) Remove bolt Fig K 12. There is a provided bolt that will go through the bracket into the frame as another securing point for the bracket.
PAGE 9
® ADDICTIVE DESERT DESIGNS DESIGNS® ® 2021-Current Ford Bronco ADD Stealth Fighter ™ Rear Bumper Installation Instructions 13. Before installing the bumper, be sure to disconnect the wiring harness from the bronco off the mount. This will free up room for the wiring harness in the ADD bumper to reach the factory connector. (Fig M) Disconnect Fig M 14.
PAGE 10
® ADDICTIVE DESERT DESIGNS DESIGNS® ® 2021-Current Ford Bronco ADD Stealth Fighter ™ Rear Bumper Installation Instructions 15. Remove the 4 bolts that connect the mount to the tire rack. (Fig O) Remove OEM x4 Screws Fig O 16. Install the Extended bracket by use the 4 provided button head bolts to bolt on the extended bracket to the mount, then use to 4 OEM screws to the bracket to the brake light bracket.
PAGE 11
® ADDICTIVE DESERT DESIGNS DESIGNS® ® 2021-Current Ford Bronco ADD Stealth Fighter ™ Rear Bumper Installation Instructions 17. On the license plate bracket you will install 2 rubber bump stops in the areas shown below in figure (Fig Q). The rubber bump stop on the far right will go through the license plate bolt. Then use the black button head bolt for the license plate along with the washer and nut facing the same orientation as the rubber bump stops.
PAGE 12
® ADDICTIVE DESERT DESIGNS DESIGNS® ® 2021-Current Ford Bronco ADD Stealth Fighter ™ Rear Bumper Installation Instructions 18. Remove the 3 factory 13mm bolts from the tire carrier shown below in. (Fig R) After the bolts have been removed you can bolt on the license plate bracket with the same OEM factory hardware.
PAGE 13
® ADDICTIVE DESERT DESIGNS DESIGNS® ® 2021-Current Ford Bronco ADD Stealth Fighter ™ Rear Bumper Installation Instructions 19. Stand back and enjoy your new ADD Stealth Fighter ™ Rear Bumper. 20. Check and re-tighten, if needed, all mounting bolts after 100 miles and periodically thereafter. This product is protected by one or more U.S. patents www.addictivedesertdesigns.