User's Manual
Table Of Contents
- Install the RF Module(s)
- Safety Precautions
- Guard against Damage from Electro-Static Discharge
- Unpack and Inspect the RF Module
- Remove Release Liners from the RF Module
- Check the DC Power Switch for the Module Bay
- Dual-Bay Modules Only—Remove the Module Bay Shelf
- Install the RF Module into the Prism Remote Chassis
- Secure RF Module Latches
- Connect the RF Module Cables to the PRU Chassis
- Power on the RF Module(s) and the Prism Remote Unit
- Close the Remote Unit Door and Solar Shield
- Provision the Prism Remote Unit
- FlexWave Notch Filter (FWP-SPRINTFILTER)
- Fan Module Maintenance
- Specifications
- Standards Certification
- DCCS Global Technical Support
- DCCS Technical Training
- Accessing FlexWave User Documentation
FlexWave
®
Prism Remote Unit and RF Module Installation Guide FWPP-504-02
Page 104 © May 2017 CommScope, Inc.
Install the RF Module(s)
Table24listshowtocorrectlyconnectHDMRFModulestotheAntennaportsonthebottomoftheRemoteUnit.
Table 24. HDM Antenna Port Mapping
RF Module Catalog # Description TX0/RX0 TX1/RX1
FWP-L4MT000MOD 20W 700 LABC Module, MIMO HDM, Single-Bay Path 1 Path 2
FWP-U4MT000MOD 20W 700 uC Module, MIMO HDM, Single-Bay Path 1 Path 2
FWP - L 4 MTU4M M O D 20W 700 LABC/700uC, Dual, Single-Bay 700 LABC 700 uC
FWP-44MT000MOD 20W 800 MIMO, Single Bay, with two External Filters Path 1 Path 2
FWP-441T841MOD* 20W 800 SMR/ 1900 PCS, Dual RF Module 1900 800
FWP-B4MT000MOD 20W 850 DUAL, MIMO, Single Bay Path 1 Path 2
FWP-C4MT000MOD 20W 850 Cell/1900 PCS, Dual, Single-Bay 1900 850
FWP-B410000MOD 20W 850 Wideband Cell, Non-Diversity Path 1 NA
FWP-B810100MOD 40W 850 Wideband Cell, Non-Diversity Path 1 NA
FWP-84MT000MOD 20W 1900 PCS Dual MIMO, Single-Bay Path 1 Path 2
FWP - 8 4 MTA4MM O D 20W 1900/2100 Dual, Single Bay 2100 1900
FWP-8416000MOD 20W 1900 PCS SISO, Non-Diversity Path 1 NA
FWP-881T000MOD 40W 1900 PCS SISO, Non-Diversity Path 1 NA
FWP-A416000MOD 20W 2100 AWS, Non-Diversity Path 1 NA
FWP-A81T000MOD 40W 2100 AWS SISO, Non-Diversity Path 1 NA
FWP-Z4MT000MOD 20W 2100 AWS-3 MIMO Path 1 Path 2
FWP - W 4 M T000 M O D 20W 2300 WCS, MIMO Path 1 Path 2
FWP-T4MT000MOD-L 20W 2500 TDD Low, MIMO, 2496.5-2571.5 MHz Path 1 Path 2
FWP-T4ST000MOD-H 20W 2500 TDD High, SISO, 2615-2690 MHz Path 1 NA
FWP-A4MT000MOD 20W HDM AWS Band 4 MIMO, Single-Bay Path 1 Path 2
* A 20W 800 SMR/ 1900 PCS, Dual RF Module RF Module (FWP-441T841MOD) requires a FlexWave Notch Filter (FWP-SPRINTFILTER)
between the Remote Unit and the antenna to provide protection from spurious emissions in the Public Safety band below 861.35
MHz and the Cellular band above 869.5 MHz. Information on how to install the Notch Filter is provided in "FlexWave Notch Filter
(FWP-SPRINTFILTER)” on page 114.