User's Manual

Table Of Contents

Page36 FlexWavePrismRemoteUnitRFModuleInstallationGuide

4 Workingfromthebottomconnectorup,connecttheRFModulecables,asfollows:

a ConnecttheMODNTX1/RX1cabletotheRFModule.

i ConstraintheMODNTX1/RX1cableofthelowerRFModulebaytoaccompanyingcablesusingatie

wrapsoitcannotbepinchedorpreventthePRUdoorfromclosing.

ii ConnecttheMODNTX1/RX1cabletotheTX1/RX1orN/C,N‐StyleJackoftheupperRFModulebay.

iii Turnthecouplingnutoftheplugclockwisetothreadontothejackandfinger‐tighten.

iv Torquecouplingnutto8±1in‐lbstoensurefullconnection.

NOTE: InsufficienttorqueappliedtoRFModuleconnectionscanresultinelevatedinsertion/returnlossandhigher

thannormalVSWRreportedbythesystem.

b ConnecttheMODNTX0/RX0cabletotheRFModule.

i InserttheN‐StylePlugoftheMODNTX0/RX0cableintotheTX0/RX0N‐StyleJackofthelowerRF

Module bay. If RF Module connection is not available, constraintheMODNTX0/RX0cableto

accompanyingcablesusingatiewrapsoitcannotbepinchedorpreventthePRUdoorfromclosing.

ii Turnthecouplingnutoftheplugclockwisetothreadontothejackandfinger‐tighten.

iii Torquecouplingnutto8±1in‐lbstoensurefullconnection.

NOTE: InsufficienttorqueappliedtoRFModuleconnectionscanresultinelevatedinsertion/returnlossandhigher

thannormalVSWRreportedbythesystem.

c ConnecttheLVDSCablestotheRFModule.

i Ifavailable,connecttheMODNDIVLVDSCabletotheDIVreceptacle ofthelower RFModuleby

insertingandslidinginuntilfullyseated.IfDIVreceptacleisnotavailable,constraintheMODNDIV

LVDSCabletoaccompanyingcablesusingatiewrapsoitcannotbepinchedorpreventthePRUdoor

fromclosing.

ii ConnecttheMODNDIVLVDSCabletotheDIVreceptacleoftheupperRFModulebyinsertingand

slidinginuntilfullyseated.IfDIVreceptacleisnotavailable,constraintheMODNDIVLVDSCableto

accompanyingcablesusingatiewrapsoitcannotbepinchedorpreventthePRUdoorfromclosing.

iii Ifavailable,connecttheMODNPRIMLVDSCabletothePRIMreceptacleoftheupperRFModuleby

insertingandslidinginuntilfullyseated.IfDIVreceptacleisnotavailable,constraintheNPRIMLVDS

CabletoaccompanyingcablesusingatiewrapsoitcannotbepinchedorpreventthePRUdoorfrom

closing.

NOTE: FullinsertioncanberecognizedbyanaudibleclickastheLVDSCableConnectorlocksintotheRFModule

Receptacle. This can be verified by lightly pulling back on the LVDS connector while making sure not to

depress the release trigger. When fully inserted, the cable should not be able to be removed from the

receptacle.

d ConnectthePowercabletotheRFModule.

i ConnectthePowerCableConnectortothePWRreceptacleofthelowerRFModulebyinsertingand

slidinginuntilfullyseated.

ii ConnectthePowerCableConnectortothePWRreceptacleoftheupperRFModulebyinsertingand

slidinginuntilfullyseated.IfPWRreceptacleisnotavailable, constrain the Power Cable to

accompanyingcablesusingatiewrapsoitcannotbepinchedorpreventthePRUdoorfromclosing.

NOTE: FullinsertioncanberecognizedbyanaudibleclickasthePowerCableConnectorlocksintotheRFModule

Receptacle.ThiscanbeverifiedbylightlypullingbackonthePowerCableConnectorwhilemakingsurenot

todepressthereleasetriggerson

theendsoftheconnector.Whenfullyinserted,thecableshouldnotbe

abletoberemovedfromthereceptacle.