Install the RF Module into the Prism Remote Chassis 1 ȋȌ Ǥ NOTE: 2 Always install RF Modules from the bottom up. Do not skip a bay, as this provides more efficient heat dissipation.
Bay D Bay C HDM RF Module Bay B Bay A SeRF Module Figure 12.
Installing a Dual-Band Dual-Slot RF Module Figure 13.
Figure 14.
3 ǡ Ǥ RF Module Moun!ng hook Moun!ng Bracket at back of the PRU Chassis Receiving flange (View is looking down into the PRU chassis from the top.
Single-Slot RF Module Push the RF Module back into the chassis un(l it can go no further. Figure 15.
Push the HDM RF Module back into the chassis un)l it can go no further. HDM RF Module Figure 16.
Push the RF Module back into the chassis un(l it can go no further. Figure 17.
Secure RF Module Latches 1 ǡ ǡ ǣ • • Dz Ǧ dz ͵Ͷ Dz Ǧ dz ͵ͷǤ Connect Latches on Single-Bay and HDM RF Modules Ǧ ǡ ǡ ͳͺǤ Two latches on Single-Slot RF Modules Two latches on HDM RF Modules Figure 18.
Connect Latches on Dual-Bay RF Modules Ǧ ǡ ǡ ͳͻǤ Four latches in a Dual-Band Dual-Slot RF Module Figure 19.
Latches on Legacy Dual-Bay 40W RF Modules Ǧ ͶͲ ǡ ǡ ʹͲǤ Four latches in a Legacy Dual-Slot 40W RF Module Figure 20.
Connecting Cables in a Single-Bay RF Module Installation 1 2 3 ǡ Ǥ Dz dz ͳͺǤ ǡ Ǥ ǡ ǣ Ǧ ǡ ʹͳ ͵ͺǡ ǡ ʹʹ ͵ͻ
d 4 Ǥ i ȋȌ ȋ Dz dz ʹͶȌǤ i ǡ Ǥ Ǥ ii
CAUTION! Ensure that all cable bends are below the top edge of the Connector Interface Panel as indicated by the dashed line in the preceding figure. Failure to correctly position the cables could inhibit closing the Remote Unit door, which can result in damage to the cables. Cable Connec#ons for an HDM RF Module DATA 0 (PRIM) Cable Connec#on Notes • Always connect the Power cable. • Always connect the two LVDS cables: PRIM and DIV. • SISO requires one RF cable (TX0/RX0).
Connecting Cables in a Dual-Bay RF Module Installation 1 2 3 ǡ Ǥ Dz dz ͳͺǤ ǡ ǡ Ǥ ǡ Ǧ ǣ Ǧ ǡ ʹ͵ Ͷʹǡ Ǧ ͶͲ ǡ
ǡ Ǥ ǡ Ǥ iv Ǥ
Cable Connec#ons for a Dual-Slot RF Module Tie wrap Two N-Type RF connectors Factory-installed RX1 cable N-Type RF connector Figure 23.
Keep cable bends behind the edge of the Connector Interface Panel Tie wrap around factory-installed RX1 cable Figure 24. Cable Connections for Legacy Dual-Bay 40W RF Modules CAUTION! Ensure that all cable bends are below the top edge of the Connector Interface Panel as indicated by the dashed line in the preceding figure. Failure to correctly position the cables could inhibit closing the Remote Unit door, which can result in damage to the cables.
Power on the RF Module(s) and the Prism Remote Unit 1 2 ǡ Ǥ Ǥ ȋ ǡ Ǣ ͳ ǤȌ Status LED POWER 48VDC/XXA NETWORK MOD D TX1/RX1 MOD D TX0/RX0 MOD D TX1
3 Ǥ • • Ǧ Ǧ ǡ Ǥ ǡ Ǧ Ϊ Ǧ ǡ Ǣ Ǥ Ǧ ͶͲ Ǥ Ǧ ͶͲ Ϊ ǡ
Close the Remote Unit Door and Solar Shield 1 2 3 Ȅ Ǥ Ȅ Ǥ ǡ ǡ Ǧ Ǥ Ȅ Ǥ Door latch Solar Shield Do
FLEXWAVE NOTCH FILTER (FWP-SPRINTFILTER) ȋ Ǧ Ȍ ǣ • • ʹͲ ͺͲͲ Ȁ ͳͻͲͲ ǡ ȋ ǦͶͶͳ ͺͶͳ Ȍ ʹͲ ͺͲͲ ǡ ǡ ȋ ǦͶͶ ͲͲͲ ȌǤ Notch Filter Installation Tips ͺͳǤ͵ͷ
ʹ Ǥ 1.13 3.81 Bo om View of Notch Filter Output N-Type Female Connector Input N-Type Female Connector NOTE: The 800 Notch Filter is designed to accept input from the PRU in either its Output or Input port, as well as the feed from the antenna. Moun,ng Bracket Band must be long enough to wrap around the pole Hose clamp sized for installa,on requirement Figure 26.
Notch Filter Specifications Frequency Range (MHz) Maximum Emissions (Sprint requirement) per 30 kHz 817-824 — < 854 < -76 dBm 854-859 < -76 dBm 859-861.35 < -76 dBm 861.35-861.5 < -56 dBm 861.5-861.6 < -42 dBm 862-869 — Enclosure Rating IP67 RF Connectors N-Type Connector, Female (2) Ground Studs (w/star washer) All ground Studs must accept AWG 6 wire Mounting Strap mount (Vertical and Horizontal) on up to 12" pole, or Wall mount Size 15.93" x 8.51" x 4.
STANDARDS CERTIFICATION FCC Ͷ ͳͷ ȋ Ȍǡ ʹʹ ȋͺͲͲ Ȍǡ ʹͶ ȋͳͻͲͲ Ǧ Ȍǡ ͻͲ ȋͺͲͲȀͻͲͲ Ǧ Ȍǡ ʹ ȋʹͳͲͲ Ǧ ǡ ͲͲ Ǧ ǡ ʹ͵ͲͲ Ǧ ǡ ʹͷͲͲ ȌǤ WARNING.
ACCESSING USER DOCUMENTATION ON THE TE CUSTOMER PORTAL ǡ Ǥ 1 ǣ ǣȀȀǤǤ ȀȀȀ 2 ȋ ǡ ǡ ENTER ǤȌ Ǥ Sign In ǡ ǣ • • 3 4 ǡ Already Registered? Sign In Now
CONTACTING TE CONNECTIVITY Telephone Numbers Sales Asia Pacific +65-6294-9948 France 0800 914032 Germany 0180 2232923 Italy 0800 782374 Spain 900 983291 United Kingdom 0800 960236 USA or Canada 1-800-366-3891 Extension Connectivity Extension Wireless Extension 73000 73475 73476 Technical Support USA or Canada 1-800-530-9960 Elsewhere +1-952-917-0761 Online Access Customer Portal https://www.te.com/portal/wireless/ Technical Support for Wireless Products http://www.te.
