User's Manual
Table Of Contents
- Document Overview
- Overview of Prism Remote Units
- Overview of RF Modules for Prism Remote Units
- Configuring the System with RF
- Install the Prism Remote Unit
- Planning for a Prism Remote Unit Installation
- Unpack and Inspect the Prism Remote Unit and Components
- Mount the Prism Remote Unit
- Ground the PRU Chassis
- Connect a Network Cable to the PRU Chassis
- Connect Fiber Cable to the PRU Chassis
- Connect the Antenna Cable
- Connect the Power Wiring
- Determine the Circuit Breaker or Fuse for the PRU
- (Optional) Connect the Prism Remote Unit to a UPS
- Install the RF Module(s)
- Safety Precautions
- Guard against Damage from Electro-Static Discharge
- Unpack and Inspect the RF Module
- Remove Release Liners from the RF Module
- Check the DC Power Switch for the Module Bay
- Dual-Bay Modules Only—Remove the Module Bay Shelf
- Install the RF Module into the Prism Remote Chassis
- Secure RF Module Latches
- Connect the RF Module Cables to the PRU Chassis
- Power on the RF Module(s) and the Prism Remote Unit
- Close the Remote Unit Door and Solar Shield
- Provision the Prism Remote Unit
- FlexWave Notch Filter (FWP-SPRINTFILTER)
- Fan Module Maintenance
- Specifications
- Standards Certification
- DCCS Global Technical Support

FWPP-501-01 Issue 1 • 320000117795 Rev A FlexWave Prism Remote Unit and HDM RF Module Installation Guide
© March 2016 CommScope, Inc. Page 117
Standards Certification
STANDARDS CERTIFICATION
FCC
ThisequipmentcomplieswiththeapplicablesectionsofTitle47CFRPart15(HostUnit),Part22(800
MHzCellular),Part24(1900MHz-PCS),Part90(800/900-SMR),andPart27(2100MHz-AWS)&
(700MHz-LTE).
WARNING.ThisisNOTaCONSUMERdevice.ItisdesignatedforinstallationbyFCCLICENSEESand
QUALIFIEDINSTALLERS.YouMUSThaveanFCCLICENSEorexpressConsentofanFCCLicenseeto
operatethisdevice.UnauthorizedusemayresultinSignificantforfeiturepenalties,includingpenalties
inexcessof$100,000foreachcontinuingviolation.
NOTE:ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassAdigitaldevice,
pursuanttopart15oftheFCCRules.Theselimitsaredesignedtoprovidereasonableprotectionagainst
harmfulinterferencewhentheequipmentisoperatedinacommercialenvironment.Thisequipment
generates,uses,andcanradiateradiofrequencyenergyand,ifnotinstalledandusedinaccordancewith
theinstructionmanual,maycauseharmfulinterferencetoradiocommunications.Operationofthis
equipmentinaresidentialareaislikelytocauseharmfulinterferenceinwhichcasetheuserwillbe
requiredtocorrecttheinterferenceathisownexpense.
IC
ThisequipmentcomplieswiththeapplicablesectionsofRSS-131.Theterm“IC:”beforetheradio
certificationnumberonlysignifiesthatIndustryCanadaTechnicalSpecificationsweremet.
TheManufacturer'sratedoutputpowerofthisequipmentisforsinglecarrieroperation.Forsituations
whenmultiplecarriersignalsarepresent,theratingwouldhavetobereducedby3.5dB,especially
wheretheoutputsignalisre-radiatedandcancauseinterferencetoadjacentbandusers.Thispower
reductionistobebymeansofinputpowerorgainreductionandnotbyanattenuatorattheoutputof
thedevice.
NOTE:TocomplywithMaximumPermissibleExposure(MPE)requirements,themaximumcomposite
outputfromtheantennacannotexceed1000WattsERP(LTE,Cellular,andPCS),theantennacannot
exceed1640WattsEIRP(PCSandAWS),andtheantennamustbepermanentlyinstalledinafixed
locationthatprovidesatleast6meters(20feet)ofseparationfromallpersons.
UL/CUL
Thiswillbeinstalledinarestrictedaccesslocation.ThisequipmentcomplieswithType4,perULand
CUL50,StandardforEnclosuresforElectricalEquipment.Thisequipmentprovidesthedegreeof
protectionspecifiedbyIPX6asdefinedinIECPublication529.
FDA/CDRH
ThisequipmentusesaClass1LASERaccordingtoFDA/CDRHRules.Thisproductconformstoall
applicablestandardsof21CFRPart1040.
CAUTION:Modificationsnotexpresslyapprovedbythepartyresponsibleforcompliancecouldvoid
theuser'sauthoritytooperatetheequipment.