User's Manual
Table Of Contents
- Document Overview
- Overview of Prism Remote Units
- Overview of RF Modules for Prism Remote Units
- Configuring the System with RF
- Install the Prism Remote Unit
- Planning for a Prism Remote Unit Installation
- Unpack and Inspect the Prism Remote Unit and Components
- Mount the Prism Remote Unit
- Ground the PRU Chassis
- Connect a Network Cable to the PRU Chassis
- Connect Fiber Cable to the PRU Chassis
- Connect the Antenna Cable
- Connect the Power Wiring
- Determine the Circuit Breaker or Fuse for the PRU
- (Optional) Connect the Prism Remote Unit to a UPS
- Install the RF Module(s)
- Safety Precautions
- Guard against Damage from Electro-Static Discharge
- Unpack and Inspect the RF Module
- Remove Release Liners from the RF Module
- Check the DC Power Switch for the Module Bay
- Dual-Bay Modules Only—Remove the Module Bay Shelf
- Install the RF Module into the Prism Remote Chassis
- Secure RF Module Latches
- Connect the RF Module Cables to the PRU Chassis
- Power on the RF Module(s) and the Prism Remote Unit
- Close the Remote Unit Door and Solar Shield
- Provision the Prism Remote Unit
- FlexWave Notch Filter (FWP-SPRINTFILTER)
- Fan Module Maintenance
- Specifications
- Standards Certification
- DCCS Global Technical Support
FWPP-501-01 Issue 1 • 320000117795 Rev A FlexWave Prism Remote Unit and HDM RF Module Installation Guide
© March 2016 CommScope, Inc. Page 99
Install the RF Module(s)
Figure 32. Cable Connections for HDM RF Modules
Table24listshowtocorrectlyconnectHDMRFModulestotheAntennaportsonthebottomofthe
RemoteUnit.
Table 24. HDM Antenna Port Mapping
RF Module Catalog # Description TX0/RX0 TX1/RX1
FWP-L4MT000MOD 20W 700 LABC Module, MIMO HDM, Single-Bay Path 1 Path 2
FWP-U4MT000MOD 20W 700 uC Module, MIMO HDM, Single-Bay Path 1 Path 2
FWP-L4MTU4MMOD 20W 700 LABC/700uC, Dual, Single-Bay 700 LABC 700 uC
FWP-44MT000MOD 20W 800 MIMO, Single Bay, with
two External Filters Path 1 Path 2
FWP-441T841MOD
(1)
20W 800 SMR/ 1900 PCS, Dual RF Module 1900 800
FWP-B4MT000MOD 20W 850 DUAL, MIMO, Single Bay Path 1 Path 2
FWP-C4MT000MOD 20W 850 Cell/1900 PCS, Dual, Single-Bay 1900 850
FWP-84MT000MOD 20W 1900 PCS Dual MIMO, Single-Bay Path 1 Path 2
FWP-84MTA4MMOD 20W 1900/2100 Dual, Single Bay 2100 1900
FWP-W4MT000MOD 20W 2300 WCS FDD, MIMO Path 1 Path 2
FWP-T4MT000MOD-L 20W 2500 TDD Low, MIMO Path 1 Path 2
FWP-T4ST000MOD-H 20W 2500 TDD High, SISO, 2615-2690 Path 1 NA
FWP-A4MT000MOD 20W HDM AWS Band 4 MIMO, Single-Bay Path 1 Path 2
(1) A 20W 800 SMR/ 1900 PCS, Dual RF Module RF Module (F
WP-441T841MOD) requires a FlexWave Notch Filter
(FWP-SPRINTFILTER) between the Remote Unit and the antenna to provide protection from spurious emissions in the Public
Safety band below 861.35 MHz and the Cellular band above 869.5 MHz. Information on how to install the Notch Filter is provided
in "FlexWave Notch Filter (FWP-SPRINTFILTER)” on page 108.
Cable Connecons for an HDM RF Module
TX0/RX0
TX1/RX1
POWER
DATA 1 (DIV)
DATA 0 (PRIM)
Cable Connecon Notes
• Always connect the Power cable.
• Always connect the two LVDS cables: PRIM and DIV.
• SISO requires one RF cable (TX0/RX0).
• MIMO and Dual-Band require two RF cables
(TX1/RX1 and TX0/RX0).