User's Manual
Table Of Contents
- Document Overview
- Overview of RF Modules for Prism Remote Units
- RF Module Components
- RF Group Assignments for PRU RF Module Bays
- Understanding RF Cable Rules
- Install the RF Module(s)
- Safety Precautions
- Guard against Damage from Electro-Static Discharge
- Unpack and Inspect the RF Module
- Remove Release Liners from the RF Module
- Check the DC Power Switch for the Module Bay
- Dual-Bay Modules Only—Remove the Module Bay Shelf
- Install the RF Module into the Prism Remote Chassis
- Secure RF Module Latches
- Connect the RF Module Cables to the PRU Chassis
- Power on the RF Module(s) and the Prism Remote Unit
- Close the Remote Unit Door and Solar Shield
- Provision the Prism Remote Unit
- FlexWave Notch Filter (FWP-SPRINTFILTER)
- Standards Certification
- Accessing User Documentation on the TE Customer Portal
- Contacting TE Connectivity
Page 20 FlexWave Prism Remote Unit RF Module Installation Guide
©2015 TE Connectivity TECP-77-141 Issue 8 • 300001744178 Rev H • August 2015
RF Module Cables and Supported Bay Installations for Legacy Dual-Bay 40W RF Modules
The cables and connectors have corresponding labels as shown in Table 12 for Legacy Dual-Bay 40W RF Modules.
Table 12 also shows which RF Module type can be installed in which PRU ba
y(s) when a 40W Dual-Bay RF Module
is part of the RF Module mix in a PR
U chassis. The Single-Bay chassis is not included in Table 12.
For Dual-Bay installations, the RF
cables and connectors are labeled as MOD N TX0/RX0 and MOD N TX1/RX1,
where N refers to the top bay of the double-bay installation. For example:
• For
a Dual-Bay installation in a Quad-Bay chassis in which the RF Module is installed in the Bay D and Bay C
combination, the RF cables and connectors are labeled as MOD D TX0/RX0 and MOD D TX1/RX1.
• Fo
r a Dual-Bay installation in a Tri-Bay chassis in which the RF Module is installed in the Bay C and Bay B
combination, the RF cables and connectors are labeled as MOD C TX0/RX0 and MOD C TX1/RX1.
Table 12.
Supported Bay Assignments and RF Antenna Labels for Legacy Dual-Bay 40W RF Modules
(From Top of Remote Unit Chassis Down)
Supported Bay Combinations for Legacy 40W Dual-Bay RF Modules RF Module
Cable,
RF Module
Connector, and
Remote Antenna
Connector Label
Function
Dual-Bay Tri-Bay Tri-Bay Quad-Bay
Bay D
N/A N/A N/A
MOD D
MOD D
MOD C
Mod D TX0/RX0 Transmit RF power and
primary/Path 1 receive to/from
the antenna for RF Module D
Mod D TX1/RX1 Transmit RF power and
se
condary/Path 2 receive
to/from the antenna for RF
Module D
Bay C
N/A MOD C
MOD C
MOD C
Mod C TX0/RX0 Transmit RF power and
p
rimary/Path 1 receive to/from
the antenna for RF Module C
Mod C TX1/RX1 Transmit RF power and
se
condary/Path 2 receive
to/from the antenna for RF
Module C
Bay B
MOD B MOD B MOD B MOD B
MOD B
Mod B TX0/RX0 Transmit RF power and
pr
imary/Path 1receive to/from
the antenna for RF Module B
Mod B TX1/RX1 Transmit RF power and
se
condary/Path 2 receive
to/from the antenna for RF
Module B
Bay A
MOD A MOD A
Mod A TX0/RX0 Transmit RF power and
p
rimary/Path 1 receive to/from
the antenna for RF Module A
Mod A TX1/RX1 Transmit RF power and
se
condary/Path 2 receive
to/from the antenna for RF
Module A
Note: For Dual Module installations the center module shelf needs to be removed; see “Dual-Bay Modules Only—Remove the Module Bay
Shelf” on page 25.
Note: Install the Legacy Dual-Bay 40W RF Module in the lower-most bay in the chassis. If, however, if two Legacy Dual-Bay 40W RF Modules
a
re present, install the 2100 Module in the lower-most Bay and the 1900 Module in the upper-most Bay.