Installation Manual

Table Of Contents

Page40 FlexWavePrismRemoteUnitRFModuleInstallationGuide

b ConnecttheMODNTX0/RX0cabletotheRFModule.

i InserttheN‐StylePlugoftheMODNTX0/RX0cableintotheTX0/RX0N‐StyleJackofthelowerRF

Module bay. If RF Module connection is not available, constraintheMODNTX0/RX0cableto

accompanyingcablesusingatiewrapsoitcannotbepinchedorpreventthePRUdoorfromclosing.

ii Turnthecouplingnutoftheplugclockwisetothreadontothejackandfinger‐tighten.

iii Torquecouplingnutto8±1in‐lbstoensurefullconnection.

NOTE: InsufficienttorqueappliedtoRFModuleconnectionscanresultinelevatedinsertion/returnlossand

higherthannormalVSWRreportedbythesystem.

c ConnecttheLVDSCablestotheRFModule.

i Ifavailable,connect theMODNDIVLVDSCabletothe DIVreceptacleofthelowerRFModuleby

insertingandslidinginuntilfullyseated.IfDIVreceptacleisnotavailable,constraintheMODNDIV

LVDSCabletoaccompanyingcablesusingatiewrapsoitcannotbepinchedorpreventthePRUdoor

fromclosing.

ii ConnecttheMODNDIVLVDSCabletotheDIVreceptacleoftheupperRFModulebyinsertingand

slidinginuntilfullyseated.IfDIVreceptacleisnotavailable,constraintheMODNDIVLVDSCableto

accompanyingcablesusingatiewrapsoitcannotbepinchedorpreventthePRUdoorfromclosing.

iii Ifavailable,connecttheMODNPRIMLVDSCabletothePRIMreceptacleoftheupperRFModuleby

insertingandslidinginuntilfullyseated.IfDIVreceptacleisnotavailable,constraintheNPRIMLVDS

CabletoaccompanyingcablesusingatiewrapsoitcannotbepinchedorpreventthePRUdoorfrom

closing.

NOTE: FullinsertioncanberecognizedbyanaudibleclickastheLVDSCableConnectorlocksintotheRF

ModuleReceptacle.ThiscanbeverifiedbylightlypullingbackontheLVDSconnectorwhilemakingsure

notto

depressthereleasetrigger.Whenfullyinserted,thecableshouldnotbeabletoberemovedfrom

thereceptacle.

d ConnectthePowercabletotheRFModule.

i ConnectthePowerCableConnectortothePWRreceptacleofthelowerRFModulebyinsertingand

slidinginuntilfullyseated.

ii ConnectthePowerCableConnectortothePWRreceptacleoftheupperRFModulebyinsertingand

slidinginuntilfullyseated.IfPWRreceptacleisnotavailable, constrain the Power Cable to

accompanyingcablesusingatiewrapsoitcannotbepinchedorpreventthePRUdoorfromclosing.

NOTE: FullinsertioncanberecognizedbyanaudibleclickasthePowerCableConnectorlocksintotheRF

ModuleReceptacle.ThiscanbeverifiedbylightlypullingbackonthePowerCableConnectorwhile

makingsurenottodepressthereleasetriggerson

theendsoftheconnector.Whenfullyinserted,the

cableshouldnotbeabletoberemovedfromthereceptacle.

RefertothegraphicthatcorrespondstotheRFModulebeinginstalledinaDual‐Bay:

• Dual‐BayRFModule:Figure23onPage41

• LegacyDual‐Bay40WRFModule:Figure24onPage42.