Installation Manual
Table Of Contents
- WAVEXpress/BTS Installation and Commissioning Guide
- One - Unpacking the WAVEXpress/BTS
- Two - Internal BTS Cabling and Jumpering
- Three - Installation
- 3-1 Wall Installation
- 3-2 Table Mount
- 3-3 Rack Installation
- 3-4 Common Final Installation Procedures
- 3-4.1 Connection of the Cable Gland
- 3-4.2 Connection of the Grounding Cable
- 3-4.3 Connection of the Antennas to the Bulkhead Plate
- 3-4.4 Connection of the Optional Combiner Assembly
- 3-4.5 Connection of the Power Supply
- 3-4.6 Connection of the T1 Lines
- 3-4.7 Connection to External Alarms
- 3-4.8 Optional Voltage Standing Wave Ratio (VSWR) Check
- 3-4.9 Post Installation Checks
- 3-5 Outdoor Installation
- Four - Off-Line Commissioning
- Five - Off-Line Commissioning of a Daisy Chain
- Six - Post Off-Line Commissioning
- Seven - On-Line Commissioning
- Appendix 1 - Connection of the Combiner Assembly
- Appendix 2 - BTS Field Maintenance
- A2-1 WAVEXpress/BTS Field Replacement Maintenance
- A2-1.1 Replacing the WAVEXpress/BTS IWP card
- A2-1.2 Replacing the WAVEXpress/BTS T1 card
- A2-1.3 Replacing the WAVEXpress/BTS TRX card
- A2-1.4 Replacing the WAVEXpress/BTS RF distribution card
- A2-1.5 Replacing the clock module
- A2-1.6 Replacing power supply units
- A2-1.7 Replacing fan assemblies
- A2-1.8 Replacing filters (p/n 520081-01)
- A2-1.9 Replacing the antenna bracket with a combiner assembly
- A2-1 WAVEXpress/BTS Field Replacement Maintenance
- Checklist 1 - Installation Checklist
- Checklist 2 - Commissioning Checklist
Release 3.3, Revision A 1/99
Off-Line Commissioning 73
Locate the line labeled
Image Current
in the primary and secondary config block which are highlighted above. These
lines have the format:
iwxx_yy.zzz
where iwxx_yy.zzz indicates the IWP flash version.
The flash version number should be 01_00.101 or higher for WAVEXpress/BTS TRX POST diagnostics to be able to
run. If it is not, the flash version number will have to be changed and the BTS rebooted. To do this, refer to Chapter 8,
BTS Management, located in the Craft PC Guide.
PR I M A R Y C O N F I G B L O C K:
1 (t3)idString :PrimarYFlasHConfiGSectoR
2 (t3) version :3
3 (t3) sequenceNumber :2
4 (t3) imageCRC :0xa18h (valid)
5 (t3) imageLength :440
6 (t3) creationTime :THU JAN 01 00:00:16 1970
7 (t3) imageCurrent :image A (0x80000) iw03_00.101
8 (t3) imagePrevious :image B (0x140000) iw03_00.101
9 (t3) imageA startup file: none
10 (t3) imageB startup file:none
11 (t3) Abis signalling chno:0
12 (t3) bootLine :qu(0,0)craftpc:/home/target/vxWorks
e=172.16.80.42
13 (t3) :fffff000 h=172.16.80.43 u=target f=0xa tn=bts s=/
14 (t3) home/target/bsxstart
15 (t3)
16 (t3) S E C O N D A R Y C O N F I G B L O C K:
17 (t3)idString :SecondarYFlasHConfiGSectoR
18 (t3)version :3
19 (t3)sequenceNumber :2
20 (t3)imageCRC :0xa18h (valid)
21 (t3) imageLength :440
22 (t3) creationTime :THU JAN 01 00:00:16 1970
23 (t3)imageCurrent :image A (0x80000) iw03_00.101
24 (t3)imagePrevious :image B (0x140000) iw03_00.101
25 (t3) Abis signalling chno:0
26 (t3) imageA startup file:none
27 (t3) imageB startup file:none
28 (t3)bootLine :qu(0,0)craftpc:/home/target/vxWorks
e=172.16.80.42
29 (t3) :fffff000 h=172.16.80.43 u=target f=0xa tn=bts s=1
30 (t3) home/target/bsxstart
Figure 4-5:
Determining the IWP flash version