Installation Manual
Table Of Contents
- WAVEXpress/BTS Installation and Commissioning Guide
- One - Unpacking the WAVEXpress/BTS
- Two - Internal BTS Cabling and Jumpering
- Three - Installation
- 3-1 Wall Installation
- 3-2 Table Mount
- 3-3 Rack Installation
- 3-4 Common Final Installation Procedures
- 3-4.1 Connection of the Cable Gland
- 3-4.2 Connection of the Grounding Cable
- 3-4.3 Connection of the Antennas to the Bulkhead Plate
- 3-4.4 Connection of the Optional Combiner Assembly
- 3-4.5 Connection of the Power Supply
- 3-4.6 Connection of the T1 Lines
- 3-4.7 Connection to External Alarms
- 3-4.8 Optional Voltage Standing Wave Ratio (VSWR) Check
- 3-4.9 Post Installation Checks
- 3-5 Outdoor Installation
- Four - Off-Line Commissioning
- Five - Off-Line Commissioning of a Daisy Chain
- Six - Post Off-Line Commissioning
- Seven - On-Line Commissioning
- Appendix 1 - Connection of the Combiner Assembly
- Appendix 2 - BTS Field Maintenance
- A2-1 WAVEXpress/BTS Field Replacement Maintenance
- A2-1.1 Replacing the WAVEXpress/BTS IWP card
- A2-1.2 Replacing the WAVEXpress/BTS T1 card
- A2-1.3 Replacing the WAVEXpress/BTS TRX card
- A2-1.4 Replacing the WAVEXpress/BTS RF distribution card
- A2-1.5 Replacing the clock module
- A2-1.6 Replacing power supply units
- A2-1.7 Replacing fan assemblies
- A2-1.8 Replacing filters (p/n 520081-01)
- A2-1.9 Replacing the antenna bracket with a combiner assembly
- A2-1 WAVEXpress/BTS Field Replacement Maintenance
- Checklist 1 - Installation Checklist
- Checklist 2 - Commissioning Checklist
Release 3.3, Revision A 1/99
70 WAVEXpress/BTS Installation and Commissioning Guide
Starting XWindows Using the Craft PC
Starting the Craft PC
Step 1
Power up the Craft PC.
Step 2
At the
LILO
prompt, press [ALT]
Step 3
Start the UNIX operating system by pressing the [ENTER] key.
Starting XWindows
Step 1
Login as “build” by typing:
craftpc login:
build
[ENTER]
Step 2
Start XWindows by typing:
build@craftpc:~>
startx
[ENTER]
Establishing a Serial Connection with the BTS
In an XTerm window, type:
build@craftpc:~>
cu -l ttyS0 -s 9600
[ENTER]
Connected.
Step 3
After the returned message Connected appears, press the [ENTER] key. The prompt now changes
to the following:
bts:A->
Verifying/Changing Boot Parameters
Step 1
Ensure that a serial connection is established between the BTS and the Craft PC. After the WAVEX-
press/BTS boots normally, type:
bts:A->
bootChange
[ENTER]
Step 2
A list of boot parameters appears. Edit the parameter values with the following commands:
NOTE
☛
The following sections describe procedures performed using the Craft PC. For more
information pertaining to the use of the Craft PC, please refer to the Craft PC Guide
.
Note that all commands in bold are those entered by the user.
NOTE
☛
At the
LILO
prompt, waiting for 30 seconds (with no user input) will automatically
start the Linux operating system bootup.