Installation Manual
Table Of Contents
- WAVEXpress/BTS Installation and Commissioning Guide
- One - Unpacking the WAVEXpress/BTS
- Two - Internal BTS Cabling and Jumpering
- Three - Installation
- 3-1 Wall Installation
- 3-2 Table Mount
- 3-3 Rack Installation
- 3-4 Common Final Installation Procedures
- 3-4.1 Connection of the Cable Gland
- 3-4.2 Connection of the Grounding Cable
- 3-4.3 Connection of the Antennas to the Bulkhead Plate
- 3-4.4 Connection of the Optional Combiner Assembly
- 3-4.5 Connection of the Power Supply
- 3-4.6 Connection of the T1 Lines
- 3-4.7 Connection to External Alarms
- 3-4.8 Optional Voltage Standing Wave Ratio (VSWR) Check
- 3-4.9 Post Installation Checks
- 3-5 Outdoor Installation
- Four - Off-Line Commissioning
- Five - Off-Line Commissioning of a Daisy Chain
- Six - Post Off-Line Commissioning
- Seven - On-Line Commissioning
- Appendix 1 - Connection of the Combiner Assembly
- Appendix 2 - BTS Field Maintenance
- A2-1 WAVEXpress/BTS Field Replacement Maintenance
- A2-1.1 Replacing the WAVEXpress/BTS IWP card
- A2-1.2 Replacing the WAVEXpress/BTS T1 card
- A2-1.3 Replacing the WAVEXpress/BTS TRX card
- A2-1.4 Replacing the WAVEXpress/BTS RF distribution card
- A2-1.5 Replacing the clock module
- A2-1.6 Replacing power supply units
- A2-1.7 Replacing fan assemblies
- A2-1.8 Replacing filters (p/n 520081-01)
- A2-1.9 Replacing the antenna bracket with a combiner assembly
- A2-1 WAVEXpress/BTS Field Replacement Maintenance
- Checklist 1 - Installation Checklist
- Checklist 2 - Commissioning Checklist
Release 3.3, Revision A 1/99
66 WAVEXpress/BTS Installation and Commissioning Guide
Figure 4-1:
LEDs which should be lit after the BTS’ power is turned on
Turn BTS on. Initial LED display is:
IWP E1 TRX
SCN
ON
PWR
ON ON OFF
ON-LINE
OFF OFF OFF
FLT
OFF OFF OFF
IWP downloads code to E1 module. LED display during
download is (this takes ~ 10s):
IWP E1 TRX
SCN
ON
PWR
ON ON ON
ON-LINE
ON ON OFF
FLT
OFF ON ON
IWP completes E1 code download (this takes ~1min).
LED display is:
IWP E1 TRX
SCN
ON
PWR
ON ON ON
ON-LINE
ON ON OFF
FLT
OFF OFF ON
Note that the TRX FLT LED will stay illuminated until the TRX software has
been downloaded either using the Craft PC or the RACAL.
LED display after 5s is:
IWP E1 TRX
SCN
ON
PWR
ON ON ON
ON-LINE
FLASH ON OFF
FLT
ON ON ON
IWP downloads code to TRX module. Final LED display is:
IWP E1 TRX
SCN
ON
PWR
ON ON ON
ON-LINE
ON ON OFF
FLT
OFF ON ON
IW007901
PORT B
12
PORT A
12
ALARMS
FLT
ON/LINE
PWR
ALARMS
ENET
CDN
EXT
XREF
IWP
T1
PWR
ON
LINE
FLT
RST
SCN
PWR
ON
LINE
FLT
TX
RX
TRX