Installation Manual
Table Of Contents
- WAVEXpress/BTS Installation and Commissioning Guide
- One - Unpacking the WAVEXpress/BTS
- Two - Internal BTS Cabling and Jumpering
- Three - Installation
- 3-1 Wall Installation
- 3-2 Table Mount
- 3-3 Rack Installation
- 3-4 Common Final Installation Procedures
- 3-4.1 Connection of the Cable Gland
- 3-4.2 Connection of the Grounding Cable
- 3-4.3 Connection of the Antennas to the Bulkhead Plate
- 3-4.4 Connection of the Optional Combiner Assembly
- 3-4.5 Connection of the Power Supply
- 3-4.6 Connection of the T1 Lines
- 3-4.7 Connection to External Alarms
- 3-4.8 Optional Voltage Standing Wave Ratio (VSWR) Check
- 3-4.9 Post Installation Checks
- 3-5 Outdoor Installation
- Four - Off-Line Commissioning
- Five - Off-Line Commissioning of a Daisy Chain
- Six - Post Off-Line Commissioning
- Seven - On-Line Commissioning
- Appendix 1 - Connection of the Combiner Assembly
- Appendix 2 - BTS Field Maintenance
- A2-1 WAVEXpress/BTS Field Replacement Maintenance
- A2-1.1 Replacing the WAVEXpress/BTS IWP card
- A2-1.2 Replacing the WAVEXpress/BTS T1 card
- A2-1.3 Replacing the WAVEXpress/BTS TRX card
- A2-1.4 Replacing the WAVEXpress/BTS RF distribution card
- A2-1.5 Replacing the clock module
- A2-1.6 Replacing power supply units
- A2-1.7 Replacing fan assemblies
- A2-1.8 Replacing filters (p/n 520081-01)
- A2-1.9 Replacing the antenna bracket with a combiner assembly
- A2-1 WAVEXpress/BTS Field Replacement Maintenance
- Checklist 1 - Installation Checklist
- Checklist 2 - Commissioning Checklist
Release 3.3, Revision A 1/99
32 WAVEXpress/BTS Installation and Commissioning Guide
3-2 Table Mount
Required Materials
• 1 lightweight table stand
• 4 No. 10-32 x 3/4” machine screws
Required Tools
• Phillips screwdriver
Note on The Table Stand
The table stand is a lightweight steel stand upon which the BTS sits. This stand raises the BTS 4.5" (11.4cm) off the
table, allowing the BTS's door to be opened without hindrance. The BTS is held in position on this stand using 4 10-
32 screws. The table stand must be bolted to the table to increase the assembly's stability.
3-2.1 Installation Instructions
Step 1
Place the table stand on the table with the opening under the stand facing forwards.
Step 2
Bolt this stand to the table with customer-provided screws. There are 6 holes; three on each side of the
stand, that can accommodate screws up to 9/16” (1.2cm) in diameter.
Step 3
Place the BTS on the stand, with the door of the BTS facing forwards, as shown in Figure 3-4 : "Placing
the BTS in the table stand" on page 33.
Step 4
There are two tapped holes on each of the BTS's sides. Line these tapped holes up with the clearance
holes of the stand.
Step 5
Thread a 10-32 screw with a washer through each of the stand's clearance holes and into the tapped
holes of the BTS. Tighten the screws down as shown in Figure 3-5 : "Attaching the BTS to the table
stand" on page 34.
NOTE
☛
These materials are provided in the table mounting kit, part number M640065