Installation Manual
Table Of Contents
- WAVEXpress/BTS Installation and Commissioning Guide
- One - Unpacking the WAVEXpress/BTS
- Two - Internal BTS Cabling and Jumpering
- Three - Installation
- 3-1 Wall Installation
- 3-2 Table Mount
- 3-3 Rack Installation
- 3-4 Common Final Installation Procedures
- 3-4.1 Connection of the Cable Gland
- 3-4.2 Connection of the Grounding Cable
- 3-4.3 Connection of the Antennas to the Bulkhead Plate
- 3-4.4 Connection of the Optional Combiner Assembly
- 3-4.5 Connection of the Power Supply
- 3-4.6 Connection of the T1 Lines
- 3-4.7 Connection to External Alarms
- 3-4.8 Optional Voltage Standing Wave Ratio (VSWR) Check
- 3-4.9 Post Installation Checks
- 3-5 Outdoor Installation
- Four - Off-Line Commissioning
- Five - Off-Line Commissioning of a Daisy Chain
- Six - Post Off-Line Commissioning
- Seven - On-Line Commissioning
- Appendix 1 - Connection of the Combiner Assembly
- Appendix 2 - BTS Field Maintenance
- A2-1 WAVEXpress/BTS Field Replacement Maintenance
- A2-1.1 Replacing the WAVEXpress/BTS IWP card
- A2-1.2 Replacing the WAVEXpress/BTS T1 card
- A2-1.3 Replacing the WAVEXpress/BTS TRX card
- A2-1.4 Replacing the WAVEXpress/BTS RF distribution card
- A2-1.5 Replacing the clock module
- A2-1.6 Replacing power supply units
- A2-1.7 Replacing fan assemblies
- A2-1.8 Replacing filters (p/n 520081-01)
- A2-1.9 Replacing the antenna bracket with a combiner assembly
- A2-1 WAVEXpress/BTS Field Replacement Maintenance
- Checklist 1 - Installation Checklist
- Checklist 2 - Commissioning Checklist
Release 3.3, Revision A 1/99
Unpacking the WAVEXpress/BTS 9
1-3.5 Dual Port T1 Card
The dual port T1 card accommodates two T1 lines connected to its shielded RJ-48 jacks. The front panel of the card
accomodates both a local and remote alarm LED for each T1 port. The T1 card also features a dip switch selector
located on the side of the card to match the impedence of the T1 cable connected to each port.
T1 100-Ohm card
The following table describes the function of the connectors and indicators on a WAVEX-
press/BTS T1 card (RJ-48). Refer to the illustration on the left for the position of connectors
and indicators.
Table 1-6:
100 Ohm T1 Cards
Table 1-5:
WAVEXpress/BTS T1 card’s connectors and indicators
Connector/
Indicator
Function
PWR Green LED, lit when card has power supplied.
ONLINE Green LED, lit when card is on-line, downloaded, and
card boot process has been performed successfully.
FLT Red LED, lit when the card detects a fault or the card has
not downloaded successfully.
PORT A Port A, RJ-48 shielded jack for T1 data interface, 100 Ohm
PORT B Port B, RJ-48 shielded jack for T1 data interface, 100 Ohm
ALARM 1 Local alarm, Port A and Port B for LOS and LOF
ALARM 2 Remote Alarm, Port A and Port B
Part Number Description
M340122 Card, T1, 100 Ohm
IW352805
PORT B
12
PORT A
12
ALARMS
FLT
ON/LINE
PWR
ALARMS